Question about Nissan Cars & Trucks
Key fob lost
Posted by Anonymous on
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: key fob will not undo
If you don't have one that works for the vehicle now, you'll have to take it to your local dealer to have it programmed to the vehicle. Some will charge for this, some will do it at no charge.
If you do have a remote that is programmed and working for the vehicle, then the following steps will allow you to program another remote:
1. Enter vehicle and close all doors.
2. Put seatbelt on (or clip it into the buckle) to shut the warning buzzer off.
3. Put key in ignition, turn to run position but don't start it.
4. Press and hold the unlock button on the working key fob and hold for 4 seconds, then also press the panic button.
5. Release both buttons and you should hear a single chime to indicate it is in program mode. You have 30 seconds after the chime to program any additional remotes you want to program.
6. Press and release both the unlock and lock buttons simultaneously on the remote you are programming. You should hear another single chime.
7. Within 4 seconds after hearing the chime, press either lock or unlock button on remote that you are programming.
Posted on Oct 16, 2008
SOURCE: lost key
You cannot disable the immobiliser. If it were that easy, any car theif could defeat it by searching the internet. If you dont have any more master keys, you will have to have your local Toyota dealer reseed (reprogram) the immobiliser code, and program new keys for you. It should be about 2 hours labor and cost of keys, but only a dealer can do it. They need to use the Toyota scan tool, and access a Toyota only website with security codes.
Posted on Feb 18, 2009
You should have a switch under the dash and then just turn it to the off position. If you don't or it doesn't work (like mine) then, there is 2 fuses under the dash, put the key in the ignition and turn it forward, pull one of the fuses out and then start the car that should reset it. Then you should be able to put the fuse back. Sometimes if you put the fuse back before starting it the alarm will just continue to try and reset itself, but not start the car. If that doesn't work I have a mechanic who can pull the whole alarm out and when hes done it would look like nothing has ever been installed. Hes very good. I ended having him take my alarm out when I had the same incident happen after the 2nd time.
Posted on Feb 24, 2009
Hi there, this is a very common fault, you need to replace the drivers door actuator to stop the noise, ive done loads of these. hope this helps.
Posted on Jun 07, 2009
1. Close and lock all doors with the driver’s side power lock/unlock switch.
2. Insert key into ignition and remove it from the ignition key cylinder at least six times within 10 seconds. Your Hazard
Lamps will flash if you have performed this step successfully. NOTE: Withdraw key completely from ignition cylinder
each time. If this procedure is performed too fast, system will not enter programming mode.
3. Insert key into the ignition cylinder and turn to the ACC position.
4. Within 5 seconds, push ANY button on the remote transmitter. Your Hazard Lamps should flash. NOTE: Do not press
the button more than one time in the above step. If the button is pressed more than one time, the programming
procedure will not be successful.
5. If there are any remaining transmitters (including the old ones), unlock then lock all doors using the driver’s side
power lock/unlock switch and within 5 seconds, push ANY button on the next remote. Your Hazard Lamps should
flash. Repeat this step for each transmitter (including any existing transmitters).
6. Turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver’s side power lock/unlock switch and open the driver side door.
Posted on Nov 16, 2009
Tips for a great answer:
Apr 18, 2016 | Nissan Cars & Trucks
Sep 05, 2015 | 1999 Nissan Pathfinder
Jun 09, 2015 | 2004 Mitsubishi Outlander
Mar 14, 2015 | 2006 Nissan Micra 1.4
Mar 12, 2012 | Cars & Trucks
Mar 08, 2010 | 2005 Nissan Xterra
Dec 22, 2009 | 2004 Dodge Sprinter
Jan 11, 2018 | Nissan Cars & Trucks
14 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: