Question about 2004 Ford Explorer XLT

Open Question

Replace rear signal light bulb on 2004 ford explorer

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: Brake light, Turn signal not working rear right 06' Focus

I have a 2000 ford focus no brake lights. with the brake lights the transmission would not go into drive .replaced the brake light switch checked fuse replaced turn signal switch with no results then i moved onto the wiper switch and replaced it as much to my supp rise it fixed the problems

Posted on Aug 06, 2009

  • 1986 Answers

SOURCE: How do you remove the rear light cover in order to

Open the hatch and look to the side of the housing, there should be a tab sticking out of the side of the assembly with a screw securing it in place (It's between the trim seal and the assembly). Then in the inside of the hatch, look up to where the assembly would be, and there should be a long cylindrical nut (it's made of plastic and will have a metal center for the threads). Remove this and then you can pull the entire assembly off. You won't have a lot of room though because the wires are relatively short.

Posted on Oct 19, 2009

  • 120 Answers

SOURCE: 2007 ford 500 rear turn signal bulb replacement

This is straight from the owner's manual.

#1 Make sure the headlamp switch is in the OFF position and open the trunk.
#2 Carefully pull the carpet away to expose the backside of the tail lamp assembly.
#3 Remove the nut and washer assemblies, then pull the lamp assembly away from the vehicle.
#4 Remove the bulb socket by rotating it counterclockwise, then pulling it out of the lamp assembly.
#5 Pull the bulb straight from the socket.

Install new bulb(s) in reverse order.
Good luck

Posted on Jan 23, 2010

  • 1 Answer

SOURCE: how to replace rear turn signal light bulb

I just changed my rear turn signal. Really easy. There is two 1/4 inch bolts visible when you open the tailgate. Take both of those out and gently lift the light housing out towards the outside of the vehicle. There is two small clamps on the other side of the fixture that just slide right out when you pull on it. There you go

Posted on Feb 21, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace the rear turn signal bulb on a 1998 Ford explorer?


There is a Hatch on the plastic part of the interior behind the light. You can reach in through the hatch and twist the bulb connector out of it's socket to replace the bulb.

Feb 08, 2015 | Ford Cars & Trucks

1 Answer

What would cause 2004 thunderbird left rear turn signal to not work and bulb is o.k.


You need to check for power to rear light if none start to check wiring in reverse. Usually at turn signal switch or under drivers side carpet.

May 14, 2014 | 2004 Ford Thunderbird

1 Answer

Reverse light work but brake light and rear turn signal doesnt


If your brake lights and turn signals are out, you most likely have a blown fuse, burnt bulb, or a problem in the steering column.----------------------------------------------------------------------
digimaster iii

Dec 21, 2012 | 2002 Ford Explorer

2 Answers

2001 ford explorer sport rear driver side turn signal and brake light dont work.


Check the bulbs if the bulbs are good suspect the panel that the bulbs go into. Which are also called the sockets you may have to replace the sockets this is not an uncommon problem.

Sep 06, 2010 | 2001 Ford Explorer Sport

2 Answers

1999 ford explorer the 2 lower brake lights won't work but the 3rd upper brake light works fine ...... whats wrong ???


check the rear lower bulbs, if good nore than likely brake lamp switrch on brake pedal, 3rd lamp rns of separate circuit

Aug 13, 2010 | 1999 Ford Explorer

1 Answer

2003 Ford Explorer Sport rear turn signal acting up


if it's only the rear turn signal that does this, check the plug where the bulb snaps in. if loose or bad connection to bulb, it will sometimes work and sometimes not. if its both the front and rear turn signal bulbs, could be the combination switch. these were common failures on fords

Feb 18, 2010 | 2003 Ford Explorer Sport

1 Answer

2006 Ford Ranger. Rear passenger side tail light


Bad earth connection.Clean or replce wire.

Jun 18, 2009 | 2004 Ford Ranger

1 Answer

Rear Turn signal out


Are you getting power at the tail lamp assembly? Better yet, do you still need help?

Jun 12, 2008 | 2004 Ford Explorer

Not finding what you are looking for?
2004 Ford Explorer XLT Logo

Related Topics:

96 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...