Question about 2003 GMC Yukon XL

Open Question

Emergency flashers come on when i turn my right turn signal on

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 272 Answers

SOURCE: 1997 sonoma turn signal flasher

The flashers are located behind the instrument panel trim, roughly between the base of the steering wheel and the ashtray, just to the left of the car lighter. To access the flashers, you need to at least loosen the lower instrument panel trim. Just under the steering column there are two screws with star heads. One to the left of the column and one to the right. You need to remove both of these screws. You will need to remove your ashtray. On the upper left corner of the hole left by removing the ashtray is a 9/32 hex head screw. You need to remove it. Once these three screws are removed you should be able to pull down on this portion of trim under your instrument cluster. When you do this it may cause trim around your instrument cluster to loosen that you can just pop back into place with your hand. You won't need to pull down to far on this trim piece as there are still some screws holding the bottom. You should be able to pull it down far enough to see the flasher units behind and just to the left of the cigarette lighter. There are two flasher units and I found that the one on the right is for the turn signals.On the left the other is for the hazard flashers. It may be a hand scraping experience to replace the flasher but it beats paying someone to do it for you. They are easy to recognize because the are silver and round metallic plug ins. The flasher unit on the left is for the emergency flashers and the one on the right is for turn signals. You can place the emergency flasher unit into the slot the turn signal unit belongs until you get a replacement. These flasher units are pretty cheap.

Posted on Jun 02, 2009

emissionwiz
  • 75130 Answers

SOURCE: 1997 sonoma turn signal flasher

it is inside, under dash, on left side is a plastic sound protector, mine had 3 screws holding it up, drop this down and straight in you will see a 1" round thing - this is the flasher, pull it out and replace with new one (there are two flat prongs that plug in). It appears this is a well guarded secret!

Posted on Aug 26, 2008

  • 1 Answer

SOURCE: When turning on left turn signal, the flashers

you have two problems the flashers are shorted. I would check the wire harness at rear off the truck. Possibly a trailer light harness has shorted at the plug most of these can be taken out of the harness and the two ends will plug together without the trailer plug.

Posted on Mar 21, 2009

  • 5 Answers

SOURCE: Same truck same exact problem

the signal switch is going out

Posted on Jul 30, 2009

  • 432 Answers

SOURCE: 2003 gmc 3500 series -

Would say its the flasher but they show seperate flashers for turn and hazard.Check fuses first.Both under the hood and in the cab.

Posted on Jan 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the turn signal flasher unit on my 1989 Oldsmobile Cutlass Supreme


Should be under the dash just to the left of the steering column, sometimes, if you have 2 flashers, you can turn on the emergency flashers and listen and feel for the click, your turn signal flasher is usually right next to the emergency flasher.

May 25, 2015 | 1989 Oldsmobile Cutlass Supreme

1 Answer

RIGHT FRONT TURN SIGNAL STOPED WORKING EMERGENCE FLASHERS WORK REPLACED BULBS AND RELAY


depending on what year model you have the emergency flasher and turn see flashes are you sleep separate however if the right turn signal works and the left when does you may have an electricalproblem

May 14, 2015 | Cars & Trucks

1 Answer

When i turn the signal lights for left or right turn the emergency flasher start flashing all four turn signal lights. the emergency flashers work ok


ck your turn signal switch wiring connector because it is more than likely has been hot and melted some connections.

Oct 18, 2014 | 2000 Kia Sportage

1 Answer

I have no signal lights, left or right, on my 2000 Oldsmobile Intrigue. I was having a problem with a front bulb not contacting properly making the right signal flash rapidly. I left it flashing while


Check if your emergency flashers still work. You possibly need a new flasher. Some cars have separate flashers for turn signals and emergency flashers, but some they are both together. If your emergency flashers still operate leave them on and find the flasher (follow the clicking noise the flasher makes) and see if there is another flasher right next to it. swap with the emergency flasher and see if your turn signals work again. If so, replace the faulty flasher.

Jul 26, 2014 | 2000 Oldsmobile Intrigue

2 Answers

Turn signal will eluminate but not flash. emergancy lights work and flash fine. Have replaced the flasher and turn signal switch.


You know you have 2 flashers right, one for emergency flashers and one for signal lights? Does it refuse to flash on both sides, right and left? Have you checked all bulbs front and back are good?

Jan 27, 2013 | 1993 Plymouth Sundance

1 Answer

Control ?i have a 1997 s10 pick signal flashers ( right and left ) stopped working, fuse replaced no go, all other electrical working ( brakes /emergency flashers etc) what do you suggest mission


The flasher may have gone bad for the turn signal, and there may be a second flasher for the emergency flasher lights. Look and listen for a click of the flasher for the emergency flasher lights. Then, the other flasher is the one to replace.

Good luck on this repair.

Dec 18, 2010 | Chevrolet S 10 Cars & Trucks

1 Answer

1995 F150 the turn signals do not work, but


Look in the fuse panel and the turn signal flasher is the big round most likely yellow or silver in the corner of fuse panel. The emergency flasher is in the back side of fuse panel right directly behind the turn signal flasher.
Remove the emergency flasher and install it in place of the turn signal flasher and see if this corrects the problem and if so get a new flasher. If this does not correct it problem will most likely be the multi-function switch.

Mar 13, 2009 | 1984 Ford F 150

3 Answers

Flasher or turn signal switch


When you select left or right do any of the bulbs come on? If you select left check front and back left side if one of the bulbs did not come on the flasher will not work. Change the bulb that is out. Same with the right. If the fuse for the turn signal is good (check fuse or replace do not use visual, some appear to be good but are not).
The emergency flasher is different from the turn signal flasher. Look at manual for location of turn signal flasher. If you manually lift and lower turn signal control you may hear a clicking under the dash to locate the flasher.

Jan 02, 2009 | 1995 Chevrolet Caprice Classic

1 Answer

1991 Ford E150 turn signals do not work,emergancy flashers flash constantlly unless the flasher relay is unplugged from fuse block


Hi,

If I understand you right based on your post/description, the signal lights would still turn on even if any or both of the flasher relays are removed. Should this be the case, then the signal lights are not getting the power from the flasher relays but from the brake light circuit.

Perhaps your concern is not with any of the flasher, but simply missing or loose ground more particularly with the rear lights. Perhaps you could try determining which of the wires for the brake lights and signal lights (as they come out of the light assembly) would be ground . A test and even possibly a temporary workaround is to hard wire a second ground connection from the determined ground wire of the lights and attach it to any conveniently located bolt or screw to the body. it may be to your advantage to do this on all the rear lights assembly.

Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards. Thank you for using FixYa.

Aug 05, 2008 | 2003 Ford E150

Not finding what you are looking for?
2003 GMC Yukon XL Logo

Related Topics:

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...