Question about Cars & Trucks

Open Question

2003 saturn vue ignition cylinder housing - Cars & Trucks

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1857 Answers

SOURCE: how do i test a ignition module on 2003 saturn vue

First thing is to check for codes which would indicate if you have an ignition module issue, a crank sensor issue or possible a PCM issue. If you do not check for codes first you will create new ones and then determining the problem will be alot more difficult.

Posted on Apr 03, 2010

Ad
techbuster
  • 5081 Answers

SOURCE: How do I remove the ignition lock cylinder from a

REMOVAL

  1. Disable SIR system. (Refer to "SIR Disable/Enable Procedure (For Frontal and Curtain Inflators)".
  2. Disconnect negative battery cable.
  3. Remove lock cylinder bezel from steering column shroud by carefully prying with thin blade screwdriver.
  4. Remove shroud fasteners and remove steering column upper and lower shroud panels.
  5. Insert key into ignition lock cylinder and rotate to RUN position. Then rotate ignition cylinder back to ACC position.
  6. Depress locking button on side of ignition module assembly with a thin pick-type tool. Slide lock cylinder assembly from ignition module.
INSTALLATION

IMPORTANT: Actuator blade within ignition module housing must be in ACC position to install lock cylinder assembly. If rotated, replace it to ACC position, using needle nose pliers.

  1. Insert key into ignition lock cylinder and install into ignition module.
  2. Install steering column upper and lower shrouds and shroud fasteners.
  3. Install lock cylinder bezel.
  4. Connect negative battery cable.
  5. Enable the SIR system. (Refer to "SIR Disable/Enable Procedure (For Frontal and Curtain Inflators)".

Posted on Apr 07, 2010

Testimonial: "Great information! Thanks for the help. Now I can get the ignition rekeyed to match the doors after the dealer changed the switch."

  • 10865 Answers

SOURCE: 2003 Saturn vue serpentine belt route

hi. the belt route map is usually on a sticker under the hood. It is also in the owner manual. Finally, NAPA stores have a data base of them and will gladly print one off for you. J.

Posted on May 28, 2010

  • 1949 Answers

SOURCE: I but a new ignition cylinder and housing in my

has to be programed by dealer

Posted on Jan 23, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is ignition coil located on my 2003 Saturn vue, (6 cyl., 3.0). Misfire in cyl. #2


The coils are on the valve covers. Here is a picture. #2 cylinder is in the front head and is on the far left. f0f26624-87ab-42ea-8895-8c6ac1d3fa36.jpg

Oct 20, 2014 | 2003 Saturn VUE

2 Answers

We recently purchased a 2003 saturn vue we are having trouble with the ignition every time we go to try and start it its so hard to turn the kek you have to keep fighting with it until it starts


Try powdered graphite in the lock cylinder. NOT liquid but powdered. You can get it at auto parts stores or better grade at any good locksmith. Comes in a squeeze tube, couple of puffs into lick and work it in. It takes a short amount of time but it works great.

Mar 04, 2011 | 2003 Saturn VUE

1 Answer

Key will not turn in the ignition------replaced key still no luck saturn vue 2003


You have a bad lock cylinder. the tumblers inside dropped. you will have to replace the cylinder

Oct 22, 2010 | 2003 Saturn VUE

1 Answer

Where do i locate the spark plugs


the spark plugs are under what is called coil cassettes-the vue does not have spark plug wires or an ignition module-instead there are cassettes that sit on top of the cylinder heads which have individual "coil on plugs" for each cylinder

Sep 11, 2010 | 2003 Saturn VUE

2 Answers

How do I remove the ignition lock cylinder from a 2003 Saturn Vue for rekeying?


REMOVAL
  1. Disable SIR system. (Refer to "SIR Disable/Enable Procedure (For Frontal and Curtain Inflators)".
  2. Disconnect negative battery cable.
  3. Remove lock cylinder bezel from steering column shroud by carefully prying with thin blade screwdriver.
  4. Remove shroud fasteners and remove steering column upper and lower shroud panels.
  5. Insert key into ignition lock cylinder and rotate to RUN position. Then rotate ignition cylinder back to ACC position.
  6. Depress locking button on side of ignition module assembly with a thin pick-type tool. Slide lock cylinder assembly from ignition module.
INSTALLATION

IMPORTANT: Actuator blade within ignition module housing must be in ACC position to install lock cylinder assembly. If rotated, replace it to ACC position, using needle nose pliers.

  1. Insert key into ignition lock cylinder and install into ignition module.
  2. Install steering column upper and lower shrouds and shroud fasteners.
  3. Install lock cylinder bezel.
  4. Connect negative battery cable.
  5. Enable the SIR system. (Refer to "SIR Disable/Enable Procedure (For Frontal and Curtain Inflators)".

Apr 07, 2010 | 2003 Saturn VUE

2 Answers

How do I test a ignition module on 2003 saturn vue 3.0L?


with the use of a module tester. Some auto parts stores sell these

Apr 03, 2010 | 2003 Saturn VUE

1 Answer

Location of the evaporative cannister solenoid? 2003 saturn vue


Depends if the engine is 3.0 or a 2.2?
3.0 purge is on the top, back side of the intake. Black, cylinder. Looks the same on a 2.2, but is located next to the air filter.

Dec 19, 2008 | 2003 Saturn VUE

1 Answer

Clutch fluid leaking from bottom of crankcase/bell housing


The slave cylinder will have to be replaced and air bled from the system to make this repair.
Good luck

Nov 24, 2008 | 2003 Saturn VUE

1 Answer

I have 2007 Saturn Vue. When I put the key in the ignition it wont turn the car on. I put grafite in the lock . It got better but not much. Most annoying thing in the worlf


You should still be under warranty, unless you have more than 36,000 miles. Take it in and tell them the ignition cylinder is binding. There is a technical service bulletin for this issue that says they need to remove the cylinder, clean it, and lubricate it with a special lubricant. If this still doesn't fix it they will need to replace the ignition cylinder and probably the ignition cylinder housing too. The bulletin number is 06-02-35-016c, this should help who ever gets to fix this.

Jul 17, 2008 | 2003 Saturn VUE

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...