Question about 2007 GMC Sierra 1500

Open Question

Brake problems on 2007 gmc sierra

I just completed a complete front brake job on my 2007 GMC TRUCK , new discs , new calipers and pads .....I now have little or no brake pressure what so ever . I have checked everywhere for leaks and the fluid resivoir remains at full ....so what am I missing . I not used to these new type of trucks all my previous gmc trucks have been from the '80

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 2002 GMC Sierra 1500 rear brakes

The first problem that I see is.....

You got screwed, the rear brake shoes and the parking brake shoes and the same thing. The parking brake uses your back brake pads to set the brake.


Sorry man

Posted on Oct 24, 2008

Ad
mick-40
  • 94 Answers

SOURCE: 2002 GMC Sierra 1500 rear brakes

Hi joelalthomas, if they replaced your brakes and you never even made it home they had better warranty the work and as for the "it was a common problem on 2002-2004 trucks" well check for Chevy recalls as this is a safety issue that would have been corrected at no expense to the vehicle owner, do a little more research my friend and let me know what happens, I will check around a little as well in the meantime I would find a new garage.Do not pay any more as you said your brakes worked fine until they worked on it good luck to you As for your 4x4 did you look at the left side when you did the right side? and were they bled off properly? you can visually check to see if the calipers are functioning

Posted on Nov 11, 2008

  • 6 Answers

SOURCE: 1997 GMC Sierra Truck Ignition Switch

its a long process,you need a steering wheel puller, once its off take the hazard button assembly out, take the turn signal loose, pull old ignition out, carefully install new one, and reverse procedure and always if u get confused i would highly recomend
a chiltons manual they explain things great

Posted on Feb 16, 2009

dennymulford
  • 1055 Answers

SOURCE: 1998 GMC Sierra- runs rough then stalls when

had this problem on my neighbors 98 chevy truck with the same engine !!
it turnd out too be the fuel pressure regulator,you have too pull the upper intake too replace it!!

Posted on Jun 06, 2009

  • 400 Answers

SOURCE: 97 gmc sierra won't go into 4x4. Electronic

Take the front axle actuator out of the axle. Plug it back in and have some one push the 4x4 button. The actuator should move, it's a liniar motor. If it doesn't then the actuator is bad or there is a wiring problem. If it does there is a problem in your front diff or some where else in the system.
I'd take a guess and say it's the front actuator.

Posted on Oct 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need to replace brakes on 2000 GMC Safari. does it have disc brakes all around or drum rakse in rear?


Disc brakes in the front and drum brakes in the rear. Make sure that you repack the front bearing's with wheel grease before finishing the job.If the front rotors and or the rear drums have a rough brake pad surface,get them resurfaced before installing new brake pads or brake shoes in the rear. you can go online or your public library for complete instructions on how to replace the brakes on that vehicle.

Apr 01, 2011 | 2000 GMC Safari

1 Answer

Instructions for replacing front disc brakes.


Jack up the car, support with a jack stand. Remove the wheel, unbolt the 2 bolts on the back of the caliper, and remove the caliper and pads off the rotor. Then with a large C-clamp or caliper piston tool and the old brake pad, push the brake piston back into the caliper until it is completely seated, install the pads, lubricate where the calipers slide and reinstall. Make sure to pump the brake pedal after you are done to get the new pads against the rotors before driving.

May 22, 2010 | 1998 GMC Jimmy

4 Answers

2005 gmc seirra vibration around 50 mph


It sounds like a bad U-joint to me. The only way to properly check u-joints is by removing the driveshaft. The joint should move freely, any binding will cause the vibration.

Mar 28, 2010 | 1995 GMC Sierra C1500

1 Answer

Front brake pads rattle on a 2001 GMC Sierra 1500HD


Is it new hardware?....older pre used hardware should be replaced....also, check the dust shields behind the rotors....could be rusted loose....happened to mine

Feb 15, 2010 | 2001 GMC Sierra 1500HD

1 Answer

How to replace rear brakes in 2005GMC Sierra?


jack up truck support it remove tire you should see the caliper,on the back side you will see two small bolts lossen the bolts remove it might require some prying support the caliper,check the rotor if has grooves in it it should be turned. use a c clamp to force the piston back in the caliper be careful of the rubber seal put the new pads on reinstall the caliper tighten the bolts start the truck pump the brakes a few times go back check for leaks if none put tire back on remove support lower to ground test drive

Nov 02, 2009 | 2005 GMC Sierra

2 Answers

Grinding and rattleing sound on the brakes of a 99 Gmc Sierra


air in the brake lines can cause that, bleed the brakes out, not very difficult if u know anything bout brakes, i can give u steps if u dont know how

Jul 13, 2009 | 2000 GMC New Sierra 1500

1 Answer

Steering wheel vibrates when i apply brakes


you have warped frt disc rotors replace them and the brake pads!

Jun 30, 2009 | 1995 GMC Sierra C1500

1 Answer

1999 gmc sierra rear brake trouble


Most likely a the caliper needs to be replaced. Could be more than that though, maybe brake hose. open brake bleeder and make sure you are getting brake fluid from the hose.

May 31, 2009 | 1999 GMC Sierra

1 Answer

2002 GMC Sierra 1500 rear brakes


Hi joelalthomas, if they replaced your brakes and you never even made it home they had better warranty the work and as for the "it was a common problem on 2002-2004 trucks" well check for Chevy recalls as this is a safety issue that would have been corrected at no expense to the vehicle owner, do a little more research my friend and let me know what happens, I will check around a little as well in the meantime I would find a new garage.Do not pay any more as you said your brakes worked fine until they worked on it good luck to you As for your 4x4 did you look at the left side when you did the right side? and were they bled off properly? you can visually check to see if the calipers are functioning

Oct 16, 2008 | 2000 GMC New Sierra 1500

Not finding what you are looking for?
2007 GMC Sierra 1500 Logo

Related Topics:

165 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...