Question about 1998 Chevrolet S-10 Pickup

1 Answer

How to remove hyd line from slave cylinder - 1998 Chevrolet S-10 Pickup

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 14,384 Answers

First open bleeder screw and drain clutch fluid.While slave cylinder is in place,loosen hydraulic line,then remove bolts holding cylinder to transmission,then remove hydraulic line.

Posted on Jan 06, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is th bleed plug for hyd clutch on 1999 Ford F350?


normally on the top end of the slave cylinder
If the slave cylinder is inside the bell housing ,there will be a bleed nipple attached to the side of the housing.

Mar 13, 2015 | Ford Cars & Trucks

2 Answers

I can't get the hydraulic line out of the old slave cylinder on a 1987 Ford Ranger pickup. Should'nt it just pull out of the old slave cylinder? Is there a special tool needed to get it out or should it...


Most I have seen are threaded.......If it has never been changed It is surely frozen...You can try saturating it with PB blast penetrate every other hour and let it soak overnight...I have had to do the same type thing on a mazda truck.....If you are changing it and it dont come out you can make your own new line....they have unions that work very well and dont leak if installed properly....also you will need a small hyd. line bender.

Feb 25, 2011 | Ford Ranger Cars & Trucks

1 Answer

Replaced slave cylinder and cant build hyd. pressure


You will have to bleed out the cylinder. You can do this by removing the cap on the slave cylinder resivor under the hood. Remove the slave cylinder from the transmission leave the line hooked up. Hold the slave cylinder at a 45 degree angle with the line end pointed up. Push the metal rod in and out while holding it at a 45 degree angle until the rod gets super hard to push. Holding it at a 45 degree angle allows the air to flow out though the line and out the resivor tank up above. Just be sure the tank is full when doing this. Also after doing this you should have good pedal however in a day or so you will probably have to do it again to get all of the air out. (Most of the time the pedal will fade again in a day) but dont worry just bleed it again. after the second time it is usually good. Good luck hope this helps feel free to contact me with any more questions about this

Jan 28, 2011 | 2001 Dodge Ram 2500 Truck

1 Answer

I am removing transmission from 1994 ford explorer 5 speed manual trans 4.0L engin how do i release hyd. lone from trans slave cyl.


you have too push in the line and then there should be a white clip you have too push in and then pull line out

Mar 17, 2010 | 1994 Ford Explorer Limited

2 Answers

Same problem 1988 trooper clutch issues


Have seen em put on with the bleed screw at the bottom by mistake ?

Jul 31, 2009 | 1988 Isuzu Trooper 2 Door

1 Answer

Hyd. Slave cylinder WITHOUT bleeder


you have to replace the master and slave. if there is no bleeder, you might get lucky bench bleeding it, but the whole assy, comes from dealer pre-bled. The system is sealed and even to do a clutch or trans, you shouldnt have to take it apart. DO NOT PUSH CLUTCH WITHOUT ALL PARTS HOOKED UP! youll break it.

Mar 21, 2009 | 1999 Dodge Dakota

2 Answers

Bleeding clutch slave cylinder


i think youre doing the right thing. they are very stubborn to bleed because the hyd. line goes up high across back of engine before droppiing back down to slave cyl., trapping air. could try to gravity bleed by opening bleeder at slave, cap off of master cyl, full with fluid then it may start to come out after a bit. then try your process again. or can try to bleed at connections further up the line, working your way back to bleeder. hope this helps. be patient.

Nov 15, 2008 | 1996 Honda Accord

2 Answers

97 chevy cavalier 2.2l 5sp clutch problem


get the hyd clutch system assembly complete and pre-bleed from the dealer

Sep 03, 2008 | 1997 Chevrolet Cavalier

Not finding what you are looking for?
1998 Chevrolet S-10 Pickup Logo

153 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6918 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...