Question about Cars & Trucks

2 Answers

How to remove gokart golf trolley front wheel

Posted by on


2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Paul, your solution does not apply to the GoKart electric golf trolley. Please use the following procedure to replace the bearings in the GoKart front wheel;1. Unscrew one of the round black plastic nuts on the end of the front wheels spindle.2. Hold the remaining nut, and by twisting and pulling on it, the front wheel spindle can be pulled out.3. You can then remove the front wheel.4. Remove the old bearings and fit the new ones. They just push into the front wheel.5. Clean and grease the spindle before re-assemby.

Posted on Jan 07, 2013

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert that has over 500 points.

  • Cars & Trucks Expert
  • 325 Answers

In the centre of the wheel is a metal cap remove this to expose centre nut,remove split pin,undo nut and the whole assembly comes off..easy!!

Posted on Jan 06, 2013


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Pneumatic trolley wheels for bag trolley. prices at bunnings?

Is this a golf bag buggy, or like a hand truck?

I needed new pneumatic wheels for a hand truck trolley, and it was cheaper to buy a new trolley from Supercheap Auto !!

Big B wasn't cheaper.

Aug 27, 2017 | Cars & Trucks


Replace brake pads on rear of car

  • First, you have to get a ratchet set. You may also need some everyday tools that you should have lying around the house. You also need a trolley jack and a car stand to go under your car to stop it from falling off of the jack.
  • After you have gathered the supplies, loosen the bolts to the rear left wheel with a 17mm ratchet. Do not fully remove the bolts, but loosen them enough. After loosening, find the jack point under the car near where the wheel is. Place the stand under the jack point and jack up the car then place the car stand under the jack point at the side of the trolley jack then remove the trolley jack slowly letting the car rest on the stand. Do the same thing on the other read wheel so that the entire back is lifted slightly making it easier to work with both wheels.
  • Now remove the wheel bolts completely and remove the wheels. Locate the two 15mm bolts on the back of the brake caliper, just under the caliper holder. Remove them and liberally apply force on the caliper to get it out of the way. It’s a good idea to rest the caliper on the trolley jack to prevent you from bending any of the break pipes.
  • Once the caliper is removed, take out the brake pads and replace them with the new ones. Place the caliper back and place the bolts back in the correct position from the start and tighten fully. Place the wheel back on the car hub and tighten the bolts. The bolts won’t be able to be tightened fully since the car is still suspended. Repeat this ending process on the other wheel. Only after, using the jack under the car stands, lower the car back to the ground. Once the car is back on the ground, use the 17mm socket to make sure each wheel is completely tightened.
  • When shopping for ratchets, try to find some that have long handles so it is easier to apply the force needed to tighten the wheels’ bolts completely.
  • Congratulations on changing your brake pads and saving money that would otherwise be spent at the garage.

on Jul 08, 2010 | Volkswagen Fox Cars & Trucks

1 Answer

My Powakaddy golf wheels go at different speeds so the trolley veers to the left. I have replaced both clutches but this has not resolved the problem.

one motor has a problem and is not of the same power as the other
could be a voltage drop from resistance in a loose conection or dirty connection

Jun 25, 2017 | Cars & Trucks

1 Answer

Put jack stands uder a 2001 Lincoln LS

place the trolley jack under the front cross member . (The big bit that connects the side frames under the sump). Lift as high as possible and place the jack stands under the chassis ( moulded rails ) where the sub-frame meets . Then place the trolley jack under the rear diff and lift as high as possible Place the jack stands under the chassis at the front of the springs or track rods By using these positions you will have the cabin securely jacked up with all the wheels free to remove or to work on. Before going under try rocking the vehicle hard to ensure that it will not move off the stands.

Mar 15, 2014 | Cars & Trucks

1 Answer

How do I remove a engine and gearbox from the seat cordoba?

drop it all down in one go through the bottom then jack vehicle up and pull the engine assembly out ,i always drop onto a sort of trolley with castor wheels on but the middle bit is only 1cm off the ground it has a belly with the wheels on each corner that have L brackets to give the height to support the castor

Dec 25, 2010 | 1996 Volkswagen Golf

1 Answer

How to replace a front wheel bearing

You'll need to remove the wheel, seperate the tierod end from the wheel spindle, remove the cailper and carrier from the wheel spindle, remove the axlenut, and unbolt the 2 bolts holding the spindle to the strut housing. You need to press out the wheel hub and remove the clips on either side of the bearing and press out the bearing from the spindle.

May 02, 2010 | 1996 Volkswagen Golf

1 Answer

What is the front wheel caster spec for a VW Golf 4 Estate 2002

Hello! Unfortunately caster is not adjustable on this model. Specs are +8 degrees.

Sep 17, 2009 | 2002 Volkswagen Golf

1 Answer

Front wheel bearing 1986 Golf

Mount the tool on the wishbone and extract wheel bearing. Application example: ...... KL-0215-410 Press Tool Kit VW Golf III without Hydraulic Cylinder

Jun 28, 2009 | 1986 Volkswagen Golf

1 Answer

Need help fitting a clutch on a VW GTI Golf

undo centre wheel hub nut 30mm/32mm, socket. undo lower wish-bone outer bolts, disconect battery,/remove starter motor,/remove transmission mounting bolts to body frame ,/ remove all surrounding bolts around bell housing transmission,/ remove clutch cable from transmission,/ remove drive shafts from centre hub and transmission,/ make sure car is standing on axle stands at front of jacking points,/use a trolley jack to suport engine sump with a piece of wood,/ slide transmission away from flywheel,/lower transmision on floor,/undo all clutch plate preasure bolts 10mm,/remove thrust bearing located on centre transmision shaft ,.also make sure if fitted speedo cable needs to be clutch plate should indicate flywheel ,without fitting clutch plate wrong way round/otherwise transmision will not bolt to engine block.,

May 17, 2009 | 1999 Volkswagen GTI

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

645 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

79186 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

13735 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides