Question about 2001 Mercury Villager

1 Answer

Brake lights dont come on - 2001 Mercury Villager

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 52 Answers

Check the switch on the brake pedal arm under the dash

Posted on Jan 06, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 ford mustang mach 1 brake lights dont work dont have manual to change the fuse


I don't believe there is a separate fuse for the high-mount brake light. Never was on older cars, that brake light is just spliced into the rear brake lights. Have you checked the bulb?

Jul 11, 2012 | Cars & Trucks

1 Answer

Guages on 87 rx7 gxl dont work


I'll help with the brake lights. 1st check fuse, 2nd there is a brake light switch located at the brake pedal you will need to get under the dash & find it. Remove plug from switch & bridge plug with wire If the lights come on the switch is faulty (have the ignition on while doing this) 3rd check brake globes it is possible all are blown.

Jul 05, 2012 | Mazda Cars & Trucks

3 Answers

Brake light dont work, change bulbs, fuse, bake switch, and has power still dont work


You have a failed brake lamp relay,this is located at the back right hand in the trunk at the quater panel.

Mar 12, 2012 | 2003 Honda Civic

1 Answer

On 2002 jeep laredo brake lights dont turn on if lights arent on


That does not make any sense. Do the tail lights work? There are supposed to be separate filaments for brake lights, tail lights, and turn signals. In particular the center brake light should not be possible to be confused with tail lights or signals. Does it come on? If not, then you probably have no brake lights at all, and that is probably because of the bad fuse or the switch on the brake pedal for the brake lights.
If there is some sort of cross over between tail light and brake lights, that is usually from a bad light socket ground; which results in current backing up from one system to another. But then each is usually only half brightness.

Jul 20, 2010 | 2002 Jeep Grand Cherokee

1 Answer

2003 Impala Brake lights dont work


The brake lights are routed through the signal light switch.
Looks like that will be the next switch to replace and the problem.

Sep 06, 2009 | 2003 Chevrolet Impala

2 Answers

Turn signals work but the brake lights do not how do i get them to work? i already changed the flasher.


I have a 2001 Ford F150, my brake lights dont work. Ive replaced the bulbs, checked the fuses,and the brake switch on side of the brake pedal was replaced. I still dont have any brake lights. My third brake light works fine, along with my running lights,flashers, blinkers.

Jun 18, 2009 | 1985 Ford F150

1 Answer

Brake lights dont work


Check if you have electrical current at brake light switch.If not go back to checking the fuses and plugs.

May 28, 2009 | 2001 Honda Civic

2 Answers

Brake light dont work


check the fuse for the brake lights. The brake lights and siganl lights use the same bulb filament. The parking and running lights use a dimmer filament in the bulb. There are 2 filaments.
Your brake lights work through the multifunction switch which operates the signal lights. If the signal lights work, you may have a bad brake lamp switch which is on your brake pedal arm.
Let us know what you find.

Mar 20, 2009 | 1998 Lincoln Town Car

2 Answers

Brake lights dont work


check brake light switch..under dash up at top of brake pedal.with wiring harness on one side and spring loaded pintle on other that reads when brake pedal is applied

Nov 07, 2008 | 1999 Ford Explorer

Not finding what you are looking for?
2001 Mercury Villager Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

fordexpert

Level 3 Expert

5546 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...