Question about Cars & Trucks

1 Answer

Where is maf sensor on 1997 Mazda protege - Cars & Trucks

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 14,337 Answers

Here's what it is showing at part store,don't see it on your engine.

Posted on Jan 06, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

thutson66
  • 96 Answers

SOURCE: 2001 mazda protege will not start

well, with all that you have changed the only two possible things that are left PCM and the ECM....

Do you have an alarm system on this vehicle? If you purchased this car second hand it may have something that is inhibiting the engine from firing. From what you have told us here that would be where I would start looking.

I really hope this is helpfull

Posted on Aug 10, 2008

  • 2 Answers

SOURCE: 1997 Mazda protege transmission, Hard shifting from 1st gear

I would try a flush. If its set up like my 96, and it likely is, changing the trasmission gasket and filter will be difficult. Mine has a medal plug on the bottom and takes an allen wrench, and possibly a breaker bar. If you take out this plug, drain, flush then refill via the dipstick tube and a funnel, it may help. You may need to do this a couple of times due to fluid still in the torque converter, pan, etc.
Lucas is good stuff, I would add it again when I was done. The tranny fluid should be pink, mine looked like used oil black before I flushed it.
Also, when adding the new fluid, shift slowly up and down through all of the gears to lube well and check your fluid levels after 100 miles or so, as sometimes a bubble will form and make it look full....then not after it pops.

Posted on Dec 23, 2008

  • 1 Answer

SOURCE: 2001 mazda protege keeps stalling

my 2001 mazda protege starts hard, idles low and high at various times (never normal) and it acts as though its going to stall at all times. sparks and wires are changed no help, changed air filter no help. any idea on what to do?

Posted on Nov 26, 2009

ZJLimited
  • 17970 Answers

SOURCE: fuse box diagram for 1997 mazda protege

Idont have register, but you can find 2002-present models (Login required).

Hope helped (remember rated this post) Good luck.

Posted on Feb 20, 2010

  • 78 Answers

SOURCE: How do you repair 1997 mazda protege idle air

if the idle air control valve is the problem, you most likely have experienced some rough idling of the car while in park and maybe driving, and RPM surges while the car is idling. THIS site provides more info on it.

Posted on Feb 03, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What should the fuel pressure be on a 99 mazda protege dx with a 1.6 I keep getting a p0171 code system too lean. suspecting fuel pressure. according to my scanner all the sensors check out ok


For your caode, try

In the vast majority of cases, simply cleaning the MAF sensor does the trick. Consult your service manual for it's location if you need help. I find it's best to take it off and spray it with electronics cleaner or brake cleaner. Make sure you are careful not to damage the MAF sensor, and make sure it's dry before reinstalling
Inspect all vacuum and PCV hoses, replace if necessary
Check for a dirty fuel filter and proper fuel pressure

Sep 02, 2011 | 1999 Mazda Protege

1 Answer

I got a 2003 mazda protege 2.0 the check engin light came on. it drives great but when left to idle it sounds like its going to stall.


Could be the Mass Air Flow sensor. But I would check the cold air intake tube first, they are subject to cracking and any hole in it will cause the MAF to give false readings which will trigger the light and cause rough idle, stalling and hesitation.

Jan 31, 2011 | 2003 Mazda Protege

1 Answer

My check engine light is flashing i have a 2000 mazda protege lx I checked the obd and three codes popped up it said the engine is too lean so I put in premium gas and that helped the shaking and i put in...


Lean condition in fuel injected engine's are caused but a faulty MAF sensor, or it's dirty. Try cleaning the MAF sensor with MAF sensor cleaner which you can buy at most auto part stores. Just follow the instructions on the spray can and also add a bottle of fuel injector cleaner to your gas. This should help and the misfiring could be cause by the lean condition of your engine which should stop as soon as the lean condition is addressed.
Thank you for using Fixya and good luck

Mar 18, 2010 | 2000 Mazda Protege

1 Answer

1996 mazda protege no go when stomping gas


sounds like bad maf....mass air flow sensor... mounted in the intake air duct...first thing is to have someone scan for codes ..

Oct 28, 2009 | 1996 Mazda Protege

1 Answer

My car idle dips to low RPM at a stop i give it gas it dies


Is the engine light on? Check the air inlet hose between the throttle body & MAF sensor for cracks or leaks. Try unplugging the MAF & see if there is any difference

Apr 17, 2009 | 1997 Mazda Protege

2 Answers

Engine light on 2002 mazda protege is on even after changing o2


Try cleaning the Mass Airflow (MAF) Sensor. My 2002 Protege check engine light came on and it started stalling at stoplights if I didn't keep the engine revved a little. Manager at AutoZone checked the computer code for the light (P0171?), and it said it was running lean. He suggested I try the MAF sensor cleaner they have ($6.99) rather than replacing the 02 sensor, etc.; it made a *significant* difference. (I think I need to do it again to get it totally cleaned out, but the can is for at least 4 cleanings.) The MAF sensor is the large component that air goes through right after the air filter. If you don't have the repair manual for the car (search online for PDF's), you search for the part online to see what it looks like. Mainly, it's a tube about 4" across with some small wire things inside. The cleaner can said it was a 10 minute job; mine took 20 minutes, but only because the tube leading from the MAF sensor to whatever is next (a kind of bent elbow tube, with a couple of accordian-style ripples) tore, and I had to duct-tape that up to seal it. (Still haven't gotten that replaced - found them online for ~$40. Maybe this weekend...)

Apr 01, 2009 | 2002 Mazda Protege

1 Answer

What is code P1195 on 97 mazda protege?


That code is for the EGR boost sensor. It has an open or a short in one of the wires.

Dec 10, 2008 | 1997 Mazda Protege

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...