Question about 1996 Oldsmobile Ninety Eight

1 Answer

I would like to know the factory ground clearance for my 96 olds model 98. Thanks Art

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 379 Answers

Hi art , i think they are going to call it ride height in the alignment specs . front ride height would be 9.0" - 9.8" and that point of measurement would be taken at the rocker panel 23.5" back from the center of the front axel (center of tire) to the bottom of the rocker panel .and the rear height would be 9.05" - 9.85" , and that point of measurement would be 23.5" from the center of the rear axel forward to the bottom of the rocker panel .see pic
I would like to know - 4b869e6.jpg

Posted on Jan 20, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Rear seat headrests

check 97 and 98 models might have replace old seats with new seats with head rests.

Jul 28, 2013 | Subaru Cars & Trucks

1 Answer

I just replaced the fuel pump on my 98 silverado z71 and the harness that came with the new pumps wiring is different. the old harness has four wires colored gray on b, purple and white on a, two black,...

I may not be of much help.
According to autozone online, 96-98 model trucks should have - -
gray from relay to the pump
black / white ground for pump
pink - black for gauge ground
pink to gas gauge
You should be able to jumper the pump relay and look for a hot for the pump. You should have two grounds, I doubt it makes much difference which you use for the pump. And then you should have a hot for the gauge with the key on and the relay disconnected.

Jul 11, 2012 | Chevrolet Cars & Trucks

1 Answer

Tappet clearance on honda integera 1998 model thanks

Best to refer to the manual - 98 Integra workshop.

It's a bit of a big download but should help you out. Cheers, Dan

Apr 28, 2011 | Honda Insight Cars & Trucks

1 Answer

I have the factory manual for a 96. 97 is

I suggest you pick up the manual for the 97-98 models. They are very different on interior designs and procedures. and i've seen many mechanics change the core without the dash completely removed, but typically it's more then 4-5 inches.

Jan 26, 2010 | 1998 Lincoln Mark VIII

1 Answer

No fire to coil from coil on 96 model Jeep Grand Cherokee.

You need to put the harmonic balance for the 96 jeep on this motor,then put the crankshaft sensor on for the 96 jeep on the vehicle,this should fix you up.The crankshaft sensor and the harmonic balance have to go together.If I can be further help,let me know.>>

Aug 18, 2009 | 1996 Jeep Grand Cherokee

1 Answer

My dash board light out... honda accord 98

Well, You shouldn't have cut the old wires. This means you now have to Buy a new factory harness. both, the male and female ends.

Jun 12, 2009 | 1993 Saturn SC2

1 Answer

96 escort valve clearance

Gary, the 1.9L Ford engine has hydraulic lifters no valve adjustment is needed

May 18, 2009 | 1989 Ford Escort

1 Answer

Need to find routing diagram for a 96 98 olds

Helm Inc. makes the factory repair manuals, or you could go to an auto parts store (like AutoZone), they have lots of repair manuals.

Apr 26, 2009 | 1985 Oldsmobile 98

1 Answer

1998 4runner trailer light wiring not working

I recommend that you tighten the ground wire screw for starters. since the vehicle is ten years old corrosion may be the culprit.

Feb 01, 2009 | 1998 Toyota 4Runner

1 Answer

Trailer wiring

Hi Smokey,

I've got them for Six and Four wire plugs

Six wire plugs:

Horse, stock or utility trailers:
White = Ground - GD
Yellow = Left turn/Brake -LT
Green = Right turn Brake -RT
Brown = Tail and clearance lights - TM
Red or Black (not both) = Battery, aux power - A
Blue = Electric Brakes - S

Recreational Vehicle: (color, use, plug mark)
White = Ground - GD
Yellow = Not used -
Brown = Right turn Brake - RT
Green = Tail and clearance lights -TM
Black = Battery, aux power - A
Red = Left turn/Brake - LT
Blue = Electric Brakes - S

Four wire plugs:
White = Ground
Yellow = Left turn/Brake
Green = Right turn Brake
Brown = Tail and clearance lights

Ground should be 10ga.
Others 14 ga

Best regards

Jun 29, 2008 | 2005 Ford Five Hundred

Not finding what you are looking for?
1996 Oldsmobile Ninety Eight Logo

Related Topics:

196 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts


Level 3 Expert

78267 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides