Question about Cars & Trucks

1 Answer

Where is the TPS sensor located,2004 Nissan Titan 5.6 v-8

Diagnostic test said TPS sensor,.where is it located

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 5,763 Answers

The 2004 nissan titan is drive by wire, meaning there is no cable to control the gas pedal to throttle.
This system is computer controlled with a motor at throttle body and pedal sensors.

the TPS throttle position sensor is located inside the throttlebody . on most of these the complete throttle body must be replaced as there is no sperate tps sensor it is complete,
i would check and make sure this is the problem . GM started making TPS replacement sensors for there throttle bodies.

Posted on Jan 06, 2013

  • Larry Radeker
    Larry Radeker Jan 08, 2013

    so is there a tps at the gas pedal? This is getting expensive,Nissan doesn`t make inexpensive throttle bodys. Do I need the spacer gasket,new one or can I use the old one?

×

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

c17hydro
  • 2984 Answers

SOURCE: high idle stalls at lights code for crank sensor

Crankshaft and Camshaft Position Sensors Camshaft Position Sensor Engine timing is determined from the relationship between the crankshaft and camshaft. This relationship is maintained by a timing chain or timing belt. The Engine Management System does not control engine timing but it does monitor the relative position and speed of these shafts by monitoring signals generated by sensors. The Engine Management System (EMS) uses signals generated by the camshaft position sensor to synchronize fuel injection to the valve sequence and for the on-board diagnostic procedure for misfire detection. The EMS energizes the injector at or near the time the intake valve opens. For misfire diagnosis, the EMS compares the number of camshaft sensor reference pulses and the number of crankshaft position sensor reference pulses received. If the EMS receives an incorrect number of pulses Diagnostic Trouble Codes (DTC’s) should be stored in the EMS.
If the camshaft position sensor or circuit is faulty most engines will start. Some engine management systems will then default to a pre-programmed injector firing sequence. All injectors may be energized simultaneously or all of the injectors on one bank may be energized at the same time. If the CMP data is required for misfire detection and reliable CMP data is not present misfire detection would probably be suspended.
Related Symptoms The following symptoms can be caused by an intermittent wiring connection or faulty signal to the EMS:

  • Extended crank time with a cold engine
  • Intermittent rough running
  • Unstable idle
  • Bucking
  • Hesitation
  • Stumble
  • Chuggle
  • Poor fuel economy
  • Stalling on acceleration
Crankshaft Position Sensor Engine speed is a very important input to the Engine Management System (EMS). Crankshaft speed and position are the basis for many calculations made by the computer. Crankshaft position values are transmitted to the computer by pickup coils also known as Permanent Magnet (P/M) generators, hall-effect sensors or optical sensors. The Crankshaft Position Sensor (CKP) also known as engine speed sensor is located in close proximity to the crankshaft.
In addition the EMS uses minute variations in the CKP sensor data to determine engine misfire. The EMS uses this information in conjunction with the camshaft position sensor to perform misfire diagnostics.
Related Symptoms: No Start/Intermittent Start Condition – Can be caused by a faulty crankshaft position sensor due to loose connections, bad grounds, high resistance in the circuit, or opens in the circuit

Posted on Jun 23, 2009

  • 17 Answers

SOURCE: 2001 Ford Explorer Sport Throttle Position Sensor

Hi, Take a little time to check all earth mounts,There are some fine earthwires under the looms running from air intake if one of these is broken or dirty it can cause all the symptoms you describe. All the best. Phil

Posted on Sep 11, 2008

Brian032472
  • 150 Answers

SOURCE: blower for nissan titan

The picture I will try to attach will show you the blower motor housing. The white electrical harness rt hand upper corner is attached to the blower motor resistor. If you have checked the relay and its working ( you can check with a tester) the resistor is probably the problem. It's the most common a/c blower issue I see weekly hope I can send it and hope it helps.

Posted on Nov 08, 2008

SOURCE: WHERE IS THE CAM POSITION SENSOR LOCATED ON A 2004 NISSAN MAXIMA

WHEN YOU STAND ON THE FRONT OF THE CAR YOU ONE IS RIGHT BELOW OF THE INTAKE WHICH IS BANK 2 OR THE ONE CLOSE TO FIREWALL , BANK 1 ONE IS ON SAME SIDE NEXT TO THE RADIATOR BUT THEY BOTH ON THE CAM RIGHT SIDE OF THE ENGINE, THE EASIEST WAY TO IDENTIFY THEM IS THAT THEIR CONNECTOR IS GREEN, ONCE YOU LOCATE THEM THE CLIP NEEDS TO BE PUSHED DOWN TOWARD THE SENSOR FOR THE CONNECTOR TO BE RELEASED, ONCE YOU REMOVE THE CONNECTOR THERE WILL BE ONLY A 10MM SCREW HOLDING THE SENSOR PULL IT OUT , THE SAME SETTING THE NEW ONE PUSH IT ALL THE WAY IN , THIGHT THE 10MM SCREW, CONNECT IT BACK AND YOU'RE DONE,BUT FOR THE ONE ON THE BACK SOMETIMES MIGHT BE NECESARY FOR YOU TO TAKE THE INTAKE OFF....HOPEFULLY IS NOT YOUR CASE....



Good luck!!! and if you need the crank for hard starting on hot/warm, it is located on the botton middle section on the transmission is the only cable that goes down to a small piece of metal and it is held by a 10mm screw only to protect the sensor, you will se the sensor once you remove that small about 6-8 inches piece of metal. Then you'll be able to unescrew the 10mm screw that holds the crank position sensor. when you pull it off you'll be able to see the fly wheel inside the transmission...



you all enjoy your rides out htere!!!

Posted on Jul 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Water temp sensor on 2005 nissan titan


Here's a link to your coolant temp. sensor,you may have a coolant temp. sender too,they are by each other, Duralast Coolant Temperature Sensor SU4072 2005 Nissan Datsun Titan 2WD... Here's a part list. Part Detail There's no way to test it,just have to replace and see if it solves the problem.I have a 85 nissan 720,mine has both sensor and sender,the sender operates the gauge on dash,the sensor sends signal to the brain.

Jul 19, 2014 | 2005 Nissan Titan Crew

1 Answer

No fire for 2004 nissan titan,replaced crank position sensor,throttle body(TPS sensor),spark plugs,fuel pump.


How about the high voltage coil, the high voltage wires to the distributor cap, the cap itself and the rotor inside. Any one of these could be the problem.

Jan 20, 2013 | 2004 Nissan Titan

1 Answer

Why does my nissan Titan **** in overdrive especially when I'm going up hill


Be more specific with details- with load, with no load, does not matter what load, etc, does it die? does it stumble? does it slowly lose power?

Without that information it could range of just about everything from a restricted/plugged exhaust to inadequate fuel pressure, and then some.

You could try backflushing the Mass Aie Flow sensor with contact cleaner as well as the TPS. And start it up at night in the dark and look for arcing of ignition components.

If no codes have tripped yet, this might address the issues prior to an error code being logged.

May 03, 2012 | 2004 Nissan Titan

1 Answer

Where is the throttle position sensor located on a nissan sentra 2004 1.8s


THE TPS SENSOR LOCATED ON THE END OF THE THROTTLE SHAFT ON THE THROTTLE BODY.

Aug 30, 2011 | 2004 Nissan Sentra

1 Answer

IAT SENSOR FOR 2004 Nissan Tiran


how to replace a o2 sensor ona 2004 nissan titan

Mar 20, 2011 | 2004 Nissan Titan

1 Answer

The power do not come when i push it


No throttle response?

TEST the TPS Sensor

The gas filter isn't 6 years old, is it?

No dash lights on,no codes present?

Feb 12, 2011 | 2004 Nissan Titan

1 Answer

I have 2004 nissan titan with 110,000 miles and my service engine soon light came on. I had it checked and someone said it had something to do with the fuel area


actually could be many reasons, dont want to scare you but there are several sensors that control this grey area, Oxygen,temp,crank,mas,knock sensors. dirty air cleaner, dirty oil (oil sensor) the light will only stay lit if the computer has stored a code, so i suggest getting a scan done to narrow the possibility of causes. What sucks about this is it cost $80-100.00 for a complete engine diagnostic, (fuel pres,timing,air fuel,cat,misfires,etc..) But first,if you take the car to a auto-zone or O'reillys,maybe a napa they will perform a basic code test and hopefully give you a basic or solution to the problem. does the car still run okay? if so have them clear the code,maybe you got some bad gas or something that triggered this. Unless the car is running unusual, or you can hear, feel a problem don't be to alarmed of that light starring at you. Check all fluids,clear code which will shut light off and try again. Hows the fuel mpg holding up.

Jan 12, 2011 | 2004 Nissan Titan

1 Answer

2004 nissan titan bettery drains ans will not turn over after being charged .nas new battery


Try having your alternator tested. Also make sure the belt is tight. It's also possible to have a defective battery, take it back to where you bought it and have them test it.

Dec 20, 2009 | 2004 Nissan Titan

1 Answer

Code p0455 evap emission (large)


have the gas cap tested or just replace it, then disconnect the battery for 5 minutes to reset the code, then drive it for a few miles and see if problem comes back, if it does a trip to the dealer is in order, as this may be covered by your emission warranty which is good for 70,000 miles.

May 26, 2009 | 2004 Nissan Titan

1 Answer

Breather


Air filter box is located in the front of the engine compartment, driver's side.

Jan 10, 2009 | 2004 Nissan Titan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

571 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...