Question about 2006 Citroen C2 1.4

Open Question

Valve clearances on citroen c2 1.4 petrol

Replaced head gasket. need to re-adjust tappets

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hey there I need the exhaust and Intake(valve) clearance for a komatsu 300-6 please


note Perform the valve clearance check and adjustment at the engine cold state. 1.Remove all of the ignition coils. 2.Remove the cylinder head cover.
caution Turn the crankshaft always clockwise. 3.Turn the crankshaft clockwise, and align the timing mark on the exhaust camshaft sprocket against the upper face of the cylinder head as shown in Figure. Therefore, No.1 cylinder goes to the compression top dead center. 4.Using a thickness gauge, measure the valve clearance with the arrow shown in Figure. If deviated from the standard value, make note for the valve clearance.
Standard value:

    Intake valve 0.20 ± 0.03 mm (0.008 ± 0.0012 inch)
    Exhaust valve 0.30 ± 0.03 mm (0.012 ± 0.0012 inch)
5.Turn the crankshaft clockwise 360 degrees, and put the timing mark on the exhaust camshaft sprocket in position shown in Figure. Therefore, No. 4 cylinder goes to the compression top dead center. 6.Check the valve clearance with the arrow shown in Figure. In the same procedure as 4.
7.If the valve clearance is deviated from the standard value, remove the camshaft and the valve tappet. For the camshaft removal, refer to Camshaft Removal and Installation . 8.Using a micrometer, measure the thickness of the removed valve tappet. 9.Calculate the thickness of the newly installed valve tappet through the following equation.
A: thickness of newly installed valve tappet
B: thickness of removed valve tappet
C: measured valve clearance
Equation

    Intake valve: A = B + [C - 0.20 mm (0.008 inch)]
    Exhaust valve: A = B + [C - 0.30 mm (0.012 inch)] note The valve tappet ranges 3,000 - 3,690 mm (0.1181 - 0.1453 inch) and has 47 types per 0.015 mm (0.0006 inch). The thickness below a decimal point is stamped on the reverse side of the valve tappet. 10.Install the valve tappet selected through the procedure 9, and put the camshaft in position. For the camshaft installation, refer to Camshaft Removal and Installation .
    11.After installing the timing chain, measure the valve clearance using the procedure 3 to 6. Confirm the clearance is within the standard value.
    caution Completely remove all the old FIPG, which might be remaining among the components. 12.After completely removing the liquid gasket adhering on the timing chain case, cylinder block and cylinder head, degrease them with white gasoline.
    caution The cylinder head cover should be installed within 3 minutes of applying liquid gasket.
13.Apply a 4 mm bead of liquid gasket as illustrated.
Specified sealant:
    THREE BOND 1217G or equivalent
14. Install the cylinder head cover and tighten the tightening bolts using the following procedures.
(1) Temporarily tighten to the following torque in order shown in the illustration.
Tightening torque: 3.0 ± 1.0 N·m (27 ± 8 in-lb)(2) Tighten to the specified torque in order shown in the illustration.
Specified torque: 5.5 ± 0.5 N·m (49 ± 4 in-lb)15.Install the ignition coils.

Jan 23, 2017 | Cars & Trucks

1 Answer

Valve clearance and voltage regulator pin out +,-, Stator, Service Manual PDF download


petrol tappet clearance on petrol engines run around .010" hot inlet and .012" hot exhaust ( .009" and .011" would be minimum )
setting to no clearance will hold both valves off the seats and make starting and running difficult
as to splicing wires , you will need a chematics to get it correct
generally the practice is red is active and black is neutral with green as ground /earth
go google and type in wiring schematics for ( make and model of unit ) and see if there is a pdf version to down load

Aug 17, 2016 | Cars & Trucks

1 Answer

How to adjust tappet clearance


Solid lifters and/or manually adjustable tappets? Now you are making me feel old. Well, if you have something that old, the way it is done is to use feeler gauges to check the spacing between the tappet and the push rod when the valve is fully closed and the cam lobe for that particular valve is not pushing on the rod at all. Many of those old tappets had a slot for a screwdriver so you could turn them to make the adjustment, and then lock them in place with a wrench by tightening the binding nut onto the rocker arm (tappets are mounted on the rocker arms). Obviously, all of this has to be done with the rocker arm cover(s) removed. That means that before you start, make sure you have a fresh gasket for the cover on hand. You will never get a used gasket to seal a second time.

Feb 19, 2015 | Cars & Trucks

3 Answers

I need to set my intake and exhaust valves, can u please give me the settings.(tappet clearance)


The Chilton and Haynes manuals are your best bet. Order it at your local Autozone or goto the Library and research them online fro free.

Jan 24, 2015 | 2006 Tata Indica LSi

1 Answer

Petter engine tappet clearance


.010" hot inlet and .012" exhaust hot. if it is an air cooled engine go up.002" in settings.

Nov 30, 2014 | Cars & Trucks

1 Answer

Incorrect valve clearances


Raw petrol means no combustion in the cylinders or fuel is flooded. Check the spark plugs and ignition spark first. Noise in the cylinder head could mean engine knocking due to oversupply of fuel or unburnt fuel causing higher pressure in cylinder.

Dec 29, 2013 | 2005 Hyundai Atos

1 Answer

Valve settings


- Pull the hand brake and put transmission in neutral.
- Remove spark plug cords.
- Remove the spark plugs.
- Remove the Tappet cover
- Lift up the left front wheel.
Cylinder number 1 is toward the pulleys and belts side.
- Rotate the crankshaft anticlockwise with socket and extension rod and bring the valve tappets (intake and exhaust) No. 4 cylinder on dancing position.
NOTE: THERE ARE OTHER WAYS ALSO TO ADJUST THE FOUR VALVES AT A TIME. BUT AS DIY FOLLOW THE FOLLOWING METHOD TO AVOID ANY CONFUSION.
- Adjust the valve clearance of number 1 cylinder.
Valve clearance:
Intake 0.18 - 0.22 (cold) Exhaust 0.25 - 0.28 (cold)
- Rotate the crankshaft anticlockwise to bring the valves of cylinder 2 on dancing position and adjust the valves of No. 3 cylinder.
- Similarly rotate the crankshaft to bring the valves of No. 1 cylinder on dancing position and adjust the valves of No. 4.
- Rotate the crankshaft anticlockwise to bring the valves of cylinder No. 3 on dancing position and adjust the valve clearance of No. 2 cylinder.

May 04, 2013 | 1999 Honda Civic

1 Answer

Need to adjust tappets in 1991 ea ford 3.9 litre


These are hydraulic and require no adjustment. If they are noisy then there is a mechanical problem due to worn parts.

Feb 09, 2012 | Cars & Trucks

1 Answer

How to measure tappet clearance with dial gauge


When setting tappets, it has to be born inind that the valve stem wears an indentation into the face of the rocker. This prevents a really accurate tappet adjustment, so the customer is right again. If you do not posess a tappet setting dial gauge, a normal engineers dial gauge will do just as well. The procedure is the same as using your feeler gauge except that you set the dial gauge up on the cylinder head with the pointer resting on the head of the rocker. Press down fairly firmly on the rocker valve end and zero the gauge. Next lift up on the rocker and read off the clearance, from the gauge, Use a magnetic base to support your gauge and repeat the pocedure for each valve pair.

Mar 25, 2010 | 1988 Mitsubishi Cargo

Not finding what you are looking for?
2006 Citroen C2 1.4 Logo

Related Topics:

221 people viewed this question

Ask a Question

Usually answered in minutes!

Top Citroen Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14380 Answers

Are you a Citroen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...