Question about 2009 Dodge Caliber 2.0

Open Question

Serpentine belt diagram for 2009 dodge caliber 2.0 -

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: serpentine belt diagram:

The belt routing diagram is located on the top radiator cross member by the hood latch. You should see it when you open the hood. If it is not there, all Chrysler, Dodge, and Plymouth minivans, from 1993 to at least 1999, used the same 3.3L engine setup, so find someone with one and look for the diagram where I described.

Posted on Jul 18, 2008

Ad
localwonder
  • 6784 Answers

SOURCE: diagram for a serpentine belt replacement for 2000 avenger dodge

HI. i have posted the diagram requested below.

7109f62.jpg

Posted on Aug 24, 2009

Testimonial: "This was exactly what we needed, Thank you so very much. "

digritz
  • 530 Answers

SOURCE: I need a serpentine belt diagram for adodge

Here's your belt diagram.
if it's not correct let me know and I'll get you all the routing diagram for that year ram 1500.
Hope it helps.
bfce879.jpg

Posted on Nov 17, 2009

  • 1757 Answers

SOURCE: Need serpentine belt routing diagram for 1994 Dodge grand caravan

3.3L?
Looking at the engine from front (right side of the Van): Stating at the Top, Going Left to Right and Clockwise:
Over the Alternator
To under the Idle Pulley,
To Over the AC Compressor.
To the Left Side of the Water Pump.
To the Right side and Under the Crankshaft Pulley
To the Right side and Over and Down the Tensioner
To Under the Power Steering Pump
And Back up-to the Left side of the Alternator.
Advise when puting it on:
Put the Belt around everything else accept for the Alternator. After it is around all the rest of the Pulleys - Pull the belt up - tight from the Power steering Pump and the Idle Pulley to form a loop, holding the Belt close to the Altenator Pulley.
Using the 15mm wrench or belt tensioner bar - rotate the Tensioner Pulley towards the front of the Van and then place the belt over the Alternator.
Let me know if this helped or if you have additional information or questions. Feel free to contact me at FixYa.com!

Posted on Jan 22, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where are the camshaft sensors on a 2009 dodge caliber 2.0


Watch this video to learn how to locate your Crankshaft Sensor on a 2009 Dodge Caliber. This video represents a 2007 model which is only 2 years apart from your 2009 but the parts and placement should be the same or at least fairly close. https://www.youtube.com/watch?v=CcvCkDjyAYo

Feb 15, 2015 | 2009 Dodge Caliber

1 Answer

Serpentine belt diagram for 2008 dodge caliber 4cyl


if the belt is still on the car take a picture to know the routing of it. there should be a decal under the hood somewhere that shows the belt routing.

Sep 16, 2014 | 2008 Dodge Caliber

2 Answers

Diagram to show how to get the serpentine belt of a 2008 dodge caliber


There is a diagram in the engine compartment itself that displays belt routing and removal.

When you look at the engine and all the pulleys that the serpentine belt goes around, one of those pulleys will have a "tensioner" on it. On that "tensioner", there should be a square looking slot for you to insert a socket extension to or you may have enough room to just use the socket drive handle itself.

Rotate counter clockwise until you have relieved enough tension to slide the belt off. Reverse the procedure for re-installation.

Jun 03, 2011 | 2008 Dodge Caliber

1 Answer

Where can i get a diagram of a 2007 dodge caliber serpentine belt


Check the factory stickers under the hood or on the radiator support, sometimes they show it.

Oct 17, 2010 | 2007 Dodge Caliber SXT Sport Hatchback

3 Answers

Serpentine belt diagram for a 3,3l dodge dynasty with ac


For the 1991 DODGE DYNASTY - V6 3.3L 201ci GAS FI N R , review this informacion:

Belt Routing Diagram
- Multiple Accessory, w/o A.C. (Mfg. After 2/27/91)
- Multiple Accessory, w/A.C. (Mfg. After 2/27/91)
- Multiple Accessory, w/o A.C. (Mfg. Before 2/27/91)
- Multiple Accessory, w/A.C. (Mfg. Before 2/27/91)
684ce70.jpg


Remove the serpentine belt by using a breakover bar, rachet or serpentine belt removal tool with the correct size socket for the pulley mounting bolt. Rotate tensioner arm to release tension. Remove the belt.

Hope helped with this (remember rated this help) Good luck.

Nov 12, 2009 | 1991 Dodge Dynasty

Not finding what you are looking for?
2009 Dodge Caliber 2.0 Logo

Related Topics:

546 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...