Question about Cars & Trucks

Open Question

My v.t commodore executive series 11 air conditioner stop working when i accelerate

Works fine until i accelerate then cuts out, but when i ease back on acceleration it blows cold air again? also fan will only go to third speed, not working on high speed.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 30 Answers

SOURCE: 2000 Jeep Cherokee Air Conditioner

If compressor isn't kicking in, check the connector atop the a/c accumulator, beside the coolant recover tank, in the engine compartment. That connector is atop a black bottle, and the connector goes to the low pressure switch. These switches do fail, and you can jump a wire across the connector terminals to see if the compressor comes on (engine running). As this circuit provides part of the ground path from the compressor clutch, if the switch is open, the compressor will never turn on. If the switch is failed, it can be replaced without opening the a/c system. Just disconnect the connector, unscrew the switch, replace it, and reconnect the connector.

Posted on Aug 08, 2008

Ad
  • 2 Answers

SOURCE: Air conditioner works but not blowing out the vents

Check the air directing servo motors under the glove box. they are 2 black boxes about 3"x3". you have to clean the contacts of grease with contact cleaner spray or alcohol.

Posted on Aug 22, 2008

  • 2 Answers

SOURCE: 2003 Honda Accord 4 cyl ex Air conditioner Problem

The accord has to radiator fans, if it blows hot air and then the ac comes back on. My accord did exact same thing. The solution was replacing one of the fan. Mine happen to be right fan, when facing the front of the car. hope this might help.

Posted on Oct 05, 2008

Molson02536
  • 3854 Answers

SOURCE: Air Conditioner works intermittently

It could be your low pressure cycle switch is going bad. Check the connection to the switch and it's is located on the A/C Accumulator. The other thing to check is the A/C relay and that is located in the glove box. There is a panel in the glove box that say's relay, there is three relays in there and one of the out side relay's out of the three is the A/C. can not remember which one it is. The middle relay is the fuel pump and the other one is the third break light. Switch the two out side relays and see if your A/C get's better. the other thing too is if the R134a is just a little low, and needs to be topped off. Good luck and hope this helps. if your going to try to recharge the A/C system your self, keep in mind not to over charge.

Posted on Jun 10, 2009

chromapr
  • 267 Answers

SOURCE: Air conditioner works then stops blowing cold air

when you day the air goes on and off i assume you mean the compressor goes on and off. that is what moves th freon through the system. if you are getting cold air when the compressor is running then the problem is that the compressor is stopping and that would be because a pressure switch may be bad. it is possible that model has a thermal shut down too say if the compressor was low on lubricant and was overheating when it does run. but if it is a pressure switch that is failing and they do, it is an easy fix. if you follow the ac lines you will find the switch.it is small about the size of a sparkplug-attached to the ac line and will have a connector with two wires. if the car is running and ac is on but the compressor is not turning remove the connector and jump to two wires. the compressor will start running if the switch was bad and we are sure there is a good charge on the system. if you are getting cold air there should be a sufficient charge to close the switch. these switches can be removed without losing any freon. there is a valve below them that will shut off when the switch is removed. then all you have to do is get a new one and screw it into place,apply the connector and you are done. if that is the problem. hope this helps please let me know and good luck

Posted on May 19, 2010

Testimonial: "Good advice!"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I changed the battery in my 1998 F150 it was running fine now it doesn't run good it acts like it doesn't want to shift and it bogs down there's no codes in the light's not on?


You can try a drive cycle, see if it helps? There may be an idle relearn, if just idle issue? Usually it will relearn idle on its own by driving.
Drive Cycle Recommendations:
  1. Most OBDII monitors will complete more readily using a "steady foot" driving style during cruise or acceleration modes. Operating the throttle in a "smooth" fashion will minimize the time required for monitor completion.
  2. Fuel tank level should be between 1/2 and 3/4 fill with 3/4 fill being the most desirable.
  3. The Evaporative Monitor can only operate during the first 30 minutes of engine operation. When executing the procedure for this monitor, stay in part throttle mode and drive in a smooth fashion to minimize "fuel slosh".
WARNING
STRICT OBSERVANCE OF POSTED SPEED LIMITS AND ATTENTION TO DRIVING CONDITIONS ARE MANDATORY WHEN PROCEEDING THROUGH THE FOLLOWING DRIVE CYCLES.

For best results, follow each of the following steps as accurately as possible:
OBDII Monitor
Exercised
Drive Cycle Procedure
Purpose of
Drive Cycle Procedure
Drive Cycle
Preparation 1. Install scan tool. Turn key on with the engine off. Cycle key off, then on. Select appropriate Vehicle & Engine qualifier. Clear all DTC's/ Perform a PCM Reset. Bypasses engine soak timer. Resets OBDII Monitor status. 2. Begin to monitor the following PIDs: ECT, EVAPDC, FLI (if available) and TP MODE.
Start vehicle WITHOUT returning to Key Off. 3. Idle vehicle for 15 seconds. Drive at 64 Km/h (40 MPH) until ECT is at least 76.7°C (170° F). Prep for Monitor Entry 4. Is IAT within 4.4 to 37.8°C (40 to 100° F)? If Not, complete the following steps but, note that step 14 will be required to "bypass " the Evap monitor and clear the P1000. Engine warm-up and provide IAT input to the PCM. HEGO 5. Cruise at 64 Km/h (40 MPH) for up to 4 minutes. Executes the HEGO monitor. EVAP 6. Cruise at 72 to 104 Km/h (45 to 65 MPH) for 10 minutes (avoid sharp turns and hills) Note, to initiate the monitor: TP MODE should =PT, EVAPDC must be >75%, and FLI must be between 15 and 85% Executes the EVAP Monitor (If IAT is within 4.4 to 37.8° (40 to 100°F)) Catalyst 7. Drive in stop and go traffic conditions. Include five different constant cruise speeds, ranging from 40 to 72 Km/h (25 to 45 MPH) over a 10 minute period. Executes the Catalyst Monitor. EGR 8. From a stop, accelerate to 72 Km/h (45 MPH) at 1/2 to 3/4 throttle. Repeat 3 times. Executes the EGR Monitor. SEC AIR/CCM (Engine) 9. Bring the vehicle to a stop. Idle with transmission in drive (neutral for M/T) for 2 minutes. Executes the ISC portion of the CCM. CCM (Trans) 10. For M/T, accelerate from 0 to 80 Km/h (o to 50 MPH), continue to step 11. For A/T, from a stop and in overdrive, moderately accelerate to 80 Km/h (50 MPH) and cruise for at least 15 seconds. Stop vehicle and repeat without overdrive to 64 Km/h (40 MPH) cruising for at least 30 seconds. While at 64 Km/h (40 MPH) , activate overdrive and accelerate to 80 Km/h (50 MPH) and cruise for at least 15 seconds. Stop for at least 20 seconds and repeat step 10 five times. Executes the transmission portion of the CCM. Misfire & Fuel Monitors 11. From a stop, accelerate to 104 Km/h (65 MPH). Decelerate at closed throttle until 64 Km/h (40 MPH) (no brakes). Repeat this 3 times. Allows learning for the misfire monitor. Readiness Check 12. Access the ON-Board System Readiness (OBDII monitor status) function on the scan tool. Determine whether all non-continuous monitors have completed. If not, go to step 13. Determines if any monitor has not completed. Pending Code Check and Evap Monitor "Bypass" Check 13. With the scan tool, check for pending codes. Conduct normal repair procedures for any pending code concern. Otherwise, rerun any incomplete monitor.
Note: if the EVAP monitor is not complete AND IAT was out of the 4.4 to 37.8° C (40 to 100° F) temperature range in step #4, or the altitude is over 2438 m. (8000 ft.), the Evap "bypass" procedure must be followed.Proceed to step 14. Determines if a pending code is preventing the clearing of P1000. Evap Monitor "Bypass" 14. Park vehicle for a minimum of 8 hours. Repeat steps 2 through 12. DO NOT REPEAT STEP 1. Allow the "bypass" counter to increment to two.
© Ford Motor Company

Jun 18, 2017 | Ford F-150 Cars & Trucks

1 Answer

1993 festiva replaced the throttle body gasket now will not accelerate at temp


I have a 1997 ford E 150 customize mark 3 van have driven back and forth to work 5 years ran great Christmas Day drove down to the garage and back up to house and now it will not start turns over has spark will not fire

Jan 07, 2014 | 1993 Ford Festiva

1 Answer

Air conditioner stops when i accelerate rapidly


The air cond compressor is supposed to stop, but only if the gas pedal is pushed to the floor.
If it is cutting off and the pedal is not all the way down, you could have a problem with the throttle position sensor.
Cutting off during hard acceleration gives you a few more horsepower.

Feb 08, 2013 | 1998 Dodge Ram

1 Answer

Hey my rear lights have all of a suden stopped working are there a few things i can check myself to get them working again. the front ones are working fine and none of the back ones are but the bulbs seem...


Check your fuses (open the kick panel above accelerator pedal to access) If it's not a fuse you can get a test light for a few bucks at supercheap/repco etc.It has a needle which you push through the plastic coating on your wires to see if power is there.Try working backwards from there to check for broken wiring.

Feb 09, 2011 | 1996 Ford Contour

1 Answer

Hi my 80 series land cruiser 3f cuts out when i


sounds like crank sensor is getting wet. Don't go through water until you figure out a way to protect it.

Feb 05, 2010 | 1990 Toyota Land Cruiser

1 Answer

Car stalls when stopped, cuts out when accelerating to HWY spds.


You could have a bad or intermittent fuel pump. Not a cheap thing to have.

An OBD 2 scanner can read fuel pressure on the drive to see if your fuel pressure drops off at odd times to confirm. It can also tell if there are transcient vacuum leaks at idle which the engines idle air control cant compensate for.

Do the plugs, wires and cap too.

Dec 12, 2009 | Chevrolet Malibu Cars & Trucks

3 Answers

2003 Honda Accord 4 cyl ex Air conditioner Problem


Even under acceleration you should have cold air from vents.Does the air change from the vents to defroster or elsewhere when accelerating? Make sure you have a full charge of refrigerent..Also make sure the engine isnt running hot...

Sep 19, 2008 | 2004 Honda Accord

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

116 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

80531 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

15360 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...