Question about 1994 Toyota Camry

Open Question

How do i fix rear wheel bearings on a 1997 toyota caldina

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 4 Answers

SOURCE: noisy rear bearing?

Is isnt the rear end it would be very bad shaking and wouldnt last long because it would throw a bearing out. So its most likly the wheel bearing and you can just take it to a local automotive shop.

Posted on Aug 12, 2008

Ad
  • 8 Answers

SOURCE: how to change rear wheel bearings on toyota carina

this isn't that type of work you can do yourself. is a good idea to go to the mecanic to change this.

Posted on Apr 04, 2009

  • 136 Answers

SOURCE: how to change rear wheel bearings on 1992 toyota camry

remove the wheel, disconnect the a arms upper and lower, tie rod end,brake caliper, remove the hub, remove wheel bearing, replace, repack, and re install

Posted on May 28, 2009

motorhead427
  • 24 Answers

SOURCE: how to change a rear wheel bearing on a 1994 toyota camry

The rear wheel bearing on a toyota camry is replaced by replacing the wheel bearing and hub as a unit. this is a design change as compare to older models with two piece wheel bearings. Scotch drive wheels. Remove rear wheel. Remove rear brake drum. (note: if emergency brakes are applied you will not be able to remove brake drum) Remove dust cap and hub retaining nut. Hub should slide off as unit. Replace hub with new unit. Installation is reverse of removal.

Posted on May 30, 2009

  • 1 Answer

SOURCE: replacing 1988 toyota 4 wheel drive truck rear end

You do not not a press for this job. Good old fashion elbow grease and a block and sledge work fine. Be careful not to mushroom head the spindle though, total pain in the *** job but pretty simple.

Posted on Jul 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where can I get car part for Toyota Caldina ST 215 1999 Model?


Greetings

This is i Inform you that reliable store site is excellent site for your service or manuals.Please see it.It would be very Help full for you.

May 05, 2016 | Toyota Cars & Trucks

1 Answer

Removing and replacing rear bearing on the 1997 Toyoto Tacoma.


Hello.
You are going to need the services of a professional machine shop.

The rear wheel bearing is pressed on. You cannot change the bearing without a press. If you try this, without a press, you will damage the new bearing, and the axle.

Please save yourself some money, and take it to a machine shop.

Dec 22, 2009 | 1997 Toyota Tacoma

1 Answer

How to change a rear wheel bearing on a 1994 toyota camry


The rear wheel bearing on a toyota camry is replaced by replacing the wheel bearing and hub as a unit. this is a design change as compare to older models with two piece wheel bearings. Scotch drive wheels. Remove rear wheel. Remove rear brake drum. (note: if emergency brakes are applied you will not be able to remove brake drum) Remove dust cap and hub retaining nut. Hub should slide off as unit. Replace hub with new unit. Installation is reverse of removal.

May 30, 2009 | 1994 Toyota Camry

2 Answers

Brakes feel spongy.when pressed hard goes nearly to floor.if pedal released slightly and pressed again feels normal.this is a 1997 toyota caldina GGT with abs.have bled brakes and sgimmed discs.any ideas?


Either you did not bleed the brakes properly or they need adjusted. (rear only) Front most likely are disks. If you put pads on the front and spread the caliper pistons, you should pump the brake pedal 10 or 15 times to move the pistons out. Some ABS systems are notoriously hard to bleed.

Apr 04, 2009 | 1997 Toyota Celica

1 Answer

Noise coming from rear wheel passengers side rear


like grinding sound ??
if so it's your wheel bearing.

Jan 08, 2009 | 1997 Toyota Previa

1 Answer

1993 Toyota Paseo left rear wheel area souns like a gerbil running on a rusty tread mill? Could this be the wheel bearins and or bushings?


Remove the rear wheel & spin the brake drum. Listen for noise. Next, remove the wheel bearing cover/cap, and remove the drum & wheel bearing. Spin the hub, listen for noise. You either have rust buildup on the interior of the brake drum or bad wheel bearings.

Aug 02, 2008 | 1997 Toyota Paseo

1 Answer

Replace rear wheel bearings


I have a 1997 toyota t-100

I was wondering if anyone had a trick to take the rear wheel barings out Im stuck.

Jul 27, 2008 | 1998 Toyota T100

1 Answer

Toyota caldina 1998 GT


must put chains (if you really need them) on all 4 wheels of your all wheel drive car to prevent a speed mis-match between front and rear...a mis-match can destroy the gearboxes over prolonged use. use chains that have many cross links to lessen the effect of any speed mis-match

Jul 03, 2008 | 1998 Toyota Corolla

Not finding what you are looking for?
1994 Toyota Camry Logo

Related Topics:

118 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8560 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...