Question about Cars & Trucks

Open Question

I have a 1991 ford laser and my indicators and hazard lights have stopped working. I have changed the hazard lights fuse in the fuse box in the car but still no luck. Any ideas?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 7353 Answers

SOURCE: 96 Ford Taurus no turn signals or hazards

Take the turn signal lever and jiggle it, a lot. If they start working, the switch is bad. You can also turn on the hazards and take hold of the button and push it left , right , forward and back and see if they start working. If so, replace the turn signal/ hazard switch.

Posted on Nov 25, 2009

  • 85 Answers

SOURCE: my hazard lights and turn signals stopped flashing

i bet you have a bad multi function switch or turn sig switch. good luck

Posted on Nov 23, 2008

  • 1 Answer

SOURCE: HAZARD LIGHTS ON BUT NOT

HI,
I have the same problem - it is the relay switch attached to and behind the hazard warning triangle on the dashboard. Pull it all out (gently and replace (£60 ish). The indicators and hazard lights are on the same relay circuit. This is a well known problem for this car (amongst others - how about the wipers sticking)

Posted on Nov 25, 2008

  • 6982 Answers

SOURCE: Fuse Box Diagram

Fuses usually are labeled. However, sometimes sub-systems are not labeled. The quickest way to find your fuse is to get a volt meter or test light and check the fuses. With the key on (to energize all circuts),and the meter or probe (-) end connected to a good ground, probe into the small spaces at each end, on the back of each fuse. (if you look at any fuse while removed, you can see how esch connector spade is open on the back side) You should have 12volts at each space. Any fuse that has no voltage should be replaced. If fuse blows immediately, there is a short in that system somewhere.

Posted on Dec 16, 2008

bunnydawg
  • 5158 Answers

SOURCE: Indicators not flashing on Audi TT

i believe the audi uses two relays for the turn signals and hazzard lights so it would appear the turn relay has failed. it should be located under the dash near the steer column.... seems to me me they have some shielding under the dash so it may be hard to get to.

Posted on May 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No direction indicators hazard lights


try changing ur flasher unit also located on ur fuse box

May 02, 2014 | Hyundai Cars & Trucks

1 Answer

Flasher


Be sure the fuse is in place in the fuse-box.

Also test the relay that controls the turn indicators. Occasionally, the relay itself emits the noise heard while the turn indicator is on.

Jan 07, 2014 | 1995 Suzuki Sidekick

1 Answer

Indicators & hazard lights


it is worht checking the fuses and also keep working the hazard light switch as they are not used that often they tend to get sticky on the con tacts and that will knock out your indicators as well if they start to work after working afer working the haz switck then change the switch

Dec 30, 2013 | Mitsubishi Outlander Cars & Trucks

1 Answer

Hi wonderd if any one can help. i have a ford focus 2002 tddi estate the hazards arnt working but the indicaters are. i've changed the hazard switch for a new one and checked all the fuses in the


Look on the back of the fuse board ,for this you have to drop the fuse board as their are two fuses at the back and i know one is for the central locking ,the other ? Now when the hazard switch is disconnected the indicators shouldnt work but the only thing i can think of is the indicator unit is faulty ,do the hazards light the indicator lights up and they dont flash or is nothing happening?

Jan 24, 2013 | Ford Cars & Trucks

1 Answer

Both left and right turn indicator lights and hazard lights NOT working. Trying to locate fuse that controls. Owners manual indicates left and right stop lights -- fuses in these locations are in working...


it is probably a flasher relay,local auto parts house will have one,easy change,unplug and replug,usually round barrell looking sometimes silver in color.underdash either in harness or fuse box sometimes,they could help you locate it.

Aug 27, 2011 | Buick LeSabre Cars & Trucks

1 Answer

Turn lights wont work


The indicators have a few components in their system, being: The indicator switch The Flasher Unit/Relay The fuse & wiring The bulbs The Hazard light switch.
If the hazard switch is broken or disconnected it will stop the indicators from working, so you could check that. You can check the indicator fuse, which should be labeled on the fuse cover. If it is blown, there is likely a fault that has caused it to blow, more often than not a problem with the trailer hitch or a trailer that has been towed. The next culprit is the flasher unit. They are usually found in the fuse area, it is a black box, looks much like a relay, but slightly taller. If this is faulty it will cause the indicators to either stay on without flashing, or not work at all. You can check this by disconnecting it, and connecting a test light to the terminals, one at a time while working the indicator stalk (key on) If the light lights up then this confirms the switch is okay, and the flasher is likely faulty.

Mar 24, 2011 | 1994 Ford Econoline

2 Answers

No turn signals but flashers work


There a two modules 1 for the turn signals and 1 for the flashers. Look under your dash around the steering wheel and fuse box area for one that is in the wiring harness.

May 31, 2009 | 1991 Ford Ranger Supercab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

143 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...