Question about 2008 Chevrolet Aveo5

Open Question

Where is the reservoir for the slave cylinder on the 2008 aveo5

Posted by Anonymous on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 691 Answers

SOURCE: Just bought a used 2008 Aveo5. When it rains,

being 2008, is should still be under the warranty. Take it to the car wash and use one of the high pressure washing machine and see where is coming in from. more likely will be the tail light. if its hatchback have someone sit in the back with a flash light and while spraying the water have that person observing the leaks.

Posted on Oct 14, 2009

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does my clutch pedal stick after about 20 miles. Then when it gets cold its ok again for a time.


Probably the throw out bearing. I fit were mine I would replace the master, slave and bearing. Have to pull the transmission to do it.

Apr 10, 2016 | 2008 Chevrolet Aveo5

1 Answer

Clutch master and slave cylinder


Reservoir drained=got leak. Should be evident on one or other. Sometimes leaking at firewall hard to detect. Replace both, if one wore out the other won't be far behind. My 88 toyota pickup leaked there but replacement master cylinder rod was too long so had to use homemade spacer on firewall in engine compartment. Slave cylinder was a pain to get mounted.

Sep 29, 2017 | Cars & Trucks

1 Answer

Can not find the slave cylinder on a 1998 Kia saphia


Below the Brake Reservoir is the Clutch Reservoir. Follow the Line from the bottom of the reservoir to locate the Slave Cylinder... It is located on the Side of the Transaxle.

Apr 06, 2013 | Cars & Trucks

3 Answers

How do you bleed the clutch hydraulic system on a 2008 Mustang?


you bleed a hydraulic clutch the same way you bleed a brake system and it uses brake fluid as well.you keep bleeding until there is no more air in the clutch system.there should be a bleeder screw on the clutch slave cylinder that is were you bleed the clutch from.

Mar 18, 2011 | 2008 Ford Mustang

1 Answer

Slave cylinder is leaking fluid


remove the slave cylinder and replace. fill the clutch reservoir with dot 3 brake fluis and open the bleeder on the slave cylinder until fluid starts to run out. refill the reservoir with fluid and with the help of a friend have them push down on the clutch pedal and open the bleeder. repeat this step till no bubbles come out and keep filling the reservoir. hope this helpsonetufshoppe_113.gif

Feb 07, 2011 | 1992 Honda Accord

3 Answers

Mazda e2200 clutch repair: feels like I still have some kind of pedal springback, but without much force. No clutch at all. I assume it is hydraulic, but the only reservoir I see is for the brakes. That is...


Yes, hydraulic--check again--fender side of brake master. Slave is usual cause of leak that eventually causes master reservoir to go dry and start drawing air. Check slave for leak. If leaking, replace slave and bleed system. Make sure to bench-bleed slave before installation by opening bleeder and pouring fluid into line port.

jturcotte_373.gif
  1. Raise and support the front end on jackstands.
  2. Back off the flare nut on the fluid pipe to free the slave cylinder hose.
  3. Pull off the hose-to-bracket retaining clip and pull the hose from the bracket. Cap the pipe to prevent fluid loss.
  4. Unbolt and remove the slave cylinder.
  5. Installation is the reverse of removal. Tighten the bolt to 12-17 ft. lbs. (16-23 Nm).

Dec 04, 2010 | 1988 Mazda B2200

1 Answer

Cannot bleed 1988 ford p/u clutchmaster cylinder


you have to bench bleed. Here is a procedure from autozone.com. Let me know if this doesn't help.


HYDRAULIC SYSTEM BLEEDING
Externally Mounted Slave Cylinder

  1. Clean the reservoir cap and the slave cylinder connection.
  2. Remove the slave cylinder from the housing.
  3. Using a 3 / 32 in. punch, drive out the pin that holds the tube in place.
  4. Remove the tube from the slave cylinder and place the end of the tube in a container.
  5. Hold the slave cylinder so that the connector port is at the highest point, by tipping it about 30° from horizontal. Fill the cylinder with DOT 3 brake fluid through the port. It may be necessary to rock the cylinder or slightly depress the pushrod to expel all the air.
WARNING Pushing too hard on the pushrod will spurt fluid from the port!
  1. When all air is expelled (no more bubble are seen), install the slave cylinder.
Some fluid will be expelled during installation as the pushrod is depressed.
  1. Remove the reservoir cap. Some fluid will run out of the tube end into the container. Pour fluid into the reservoir until a steady stream of fluid runs out of the tube and the reservoir is filled. Quickly install the diaphragm and cap. The flow should stop.
  2. Connect the tube and install the pin. Check the fluid level.
  3. Check the clutch operation.

Oct 17, 2010 | Ford F-250 Cars & Trucks

2 Answers

My car is a hyundai sonata 2008. I have to pump my clutch multiple times to get the gear in. My boyfriend is looking for a clutch master cylinder reservoir. Can you tell me where it is?


When you open the hood and you're looking directly in front like facing the driver's seat it will be on the right corner when you're facing the driver's seat. It looks like a break fluid reservoir only smaller and it's usually about a foot or so below from the top.
Good luck

Oct 10, 2010 | Hyundai Sonata Cars & Trucks

1 Answer

I was driving today and had no problems out of the clutch in my 1988 f150 with 4.9 then all the suddon i push it in and the pedal goes 2 the floor and i have no clutch. what do i need to do?


You have a hydraulic clutch. It may be that the slave cylinder has been leaking and has run the reservoir dry thus allowing air into the system. Check the fluid level in the reservoir. If empty, look for leak at slave cylinder or elsewhere along the line from the master to the slave. Replace the slave cylinder or otherwise repair the leak, refill the reservoir and bleed the system. Any questions, please reply. I will paste diagram below.

1a9be7c.gif

Sep 15, 2010 | Ford F-150 Cars & Trucks

1 Answer

Just bought a used 2008 Aveo5. When it rains,


being 2008, is should still be under the warranty. Take it to the car wash and use one of the high pressure washing machine and see where is coming in from. more likely will be the tail light. if its hatchback have someone sit in the back with a flash light and while spraying the water have that person observing the leaks.

Oct 14, 2009 | 2008 Chevrolet Aveo5

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...