Question about 2006 Chevrolet Uplander

1 Answer

Disable/mute Uplander blinker noise

How do I disable the blinker clicks on a 2008 Uplander? They are quite loud and I do not forget that my blinkers are on.

Posted by on

  • Anonymous Feb 13, 2009

    Can anyone tell me where the blinker is located on a 2008 chevy uplander

  • Anonymous Mar 12, 2014

    2008 uplander

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 9 Answers

Change the blinker fluid jk remove the blinker switch fuse or power wire.

Posted on Jan 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2000 Dodge Durango and we have been having blinker problems too lately. Sometimes they worked, sometimes they didnt, and the other day they went out completely.They have been doing this for a...


that vehicle has a desperate relay for the hazards which is why they work, you have a defective signal flasher sometimes called a signal relay, follow the noise to locate exactly where the part is, usually under driver side of dash, it is a very cheap part and easy to install.

Sep 26, 2011 | 2000 Dodge Durango

2 Answers

How do you replace the blinkers flasher under the dash on a Chev S-10?


This one may be mounted directly on the fuse box or on a plug end. Turn the key on and then the blinker switch. I assume it is bad and quit working though so disregard that last idea if it is bad and not making the clicking noise any longer. It should be a little round or square silver relay. Just pull it off the end where ever it is located. If it is stuck then pull hadder being careful not to pull the wire off with it. It will come off.
It will have two maybe three metel prongs that plug it in. Just replace with new on. Thy have different levels of noise you can buy. If grandpa is getting hard of hearing and forgets to turn his blinker off then you can get a louder one. Let me know how you do on this. Raz

Apr 18, 2010 | 1995 Chevrolet S-10 CA Edition

2 Answers

Power window not working


If it was working fine before then most likely the switch has shorted or the wires to the motor have come disconnected, worst case the motor is bad, if the blinker is working but not making noise, then no need to worry, it is possible that you just need a new blinker relay.

Apr 05, 2010 | 2008 Chevrolet Equinox

2 Answers

Need loud signal flasher for 2008 Toyota RAV4


the module can be replaced by a chime or a truck blinker switch from a diesel truck shop and you may here it, however the other guy is right and has a couple good ideals. JC whitnet has one
here is the web page. and this is for the
RAV 4 http://www.jcwhitney.com/autoparts/Search?catalogId=10101&storeId=10101&sku=loud+turn+signal+flasher
g_13364g_th_1.gif;pv2b80a320e50f7422 CEC INDUSTRIES MUSICAL AND VERY LOUD TURN SIGNAL FLASHERS
Hear your turn signal over road noise and music! Select "Love Me Tender" which plays at standard volume, or our signal flasher louder than a standard flasher.
Review this product

Jun 26, 2009 | 1999 Toyota RAV4

2 Answers

Hazards and blinkers not working


There are separate fuses for the turn signals and blinkers, but you should check both of them just to see if they're good.

You may have a burnt out turn signal bulb as well. I know that this sounds like an obvious answer, but a single bulb can sometimes disable the entire system because of the way that some flashers operate.

You could also have a defective turn signal/hazard light flasher. This is located under the dash board on the driver's side between the steering column and the door. You have to remove the sound insulation/kick panel (the cover on the bottom of the dash board) to reach the flasher (it is easy to remove - I don't think you even need tools).

May 16, 2009 | 1997 Pontiac Grand Am

1 Answer

Blinker


YOU WILL NEED TO DISABLE THE AIR BAG AND REMOVE THE STEERING WHEEL.THEN YOU WILL SEE THE WIRE OR WIRES THAT HAVE RUBBED UNTIL THE BARE WIRE IS GROUNDING OUT ON SOMETHING INSIDE.

May 15, 2009 | 2000 GMC Jimmy

1 Answer

Blinker keeps clicking


replace the hazard light switch it is the flasher unit for both blinkers and hazards.

Feb 28, 2009 | 2001 Volkswagen Beetle

1 Answer

Changing rear blinker lamp 2005 uplander


use the proper tool or you may end up damagind the fastener and then it may be very difficult to remove...available at any store that has tool , couple of dollars

Sep 22, 2008 | 2006 Chevrolet Uplander

6 Answers

Beeping Noise/Blinker Noise


sounds like your electronic flasher unit maybe stuck causing the noise. they are generally located under the dash on driver side just below the instrument cluster.

Sep 10, 2008 | 2004 Oldsmobile Alero

Not finding what you are looking for?
2006 Chevrolet Uplander Logo

Related Topics:

282 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...