Question about Cars & Trucks

Open Question

Need to remove steering wheel & airbag off 07 ra Holden Rodeo

Are there Torx bits to remove or is it springs

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: Remove the steering wheel or airbag from a 2004 Volvo XC90?

You need a steering wheel puller. You may be able to rent this from your parts house. Disconnect the battery for no less than 1/2 hour before disconnecting the air bag or the air bag could deploy. Place air bag facing up or it could become a projectile if set off.

Posted on Aug 14, 2009

Ad
stevenhurc
  • 450 Answers

SOURCE: torque settings for a holden rodeo 3.5 ra. Head

stage 1 = 29Nm(21 lb ft/3.0 kg-m)
final = 64Nm(47 lb ft/6.5kg-m)
do not reuse head bolts or apply any lubricant to the bolts. Do up bolts in following order for each head.
6 1 3 7
front
5 2 4 8

Posted on Dec 05, 2009

  • 753 Answers

SOURCE: 2003 Malibu steering wheel air bag removal

It should be a T-30.

Posted on Dec 21, 2009

  • 1 Answer

SOURCE: Intermitten loss of throttle car

you need to have the throttle body cleaned out or replaced

Posted on Apr 20, 2010

  • 383 Answers

SOURCE: holden rodeo brakelights dont work not even cab brake strip.

check your fuses

Posted on May 27, 2010

Testimonial: "i found problem fuses"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Could some one please tell me where the reverse light switch on the gearbox is on a holden rodeo ra 05 thank you


07 Rodeo Reverse light switch...where is it? - Rodeo,Colorado and ...

forum.australia4wd.com > ... > Rodeo,Colorado and DMAX Technical

Nov 5, 2011 - 7 posts - ‎4 authors
posted in Rodeo,Colorado and DMAX Technical: My reversing lights ... switch as per workshop manual..could someone throw me a bone here...thanks. ... Started By rodeo5 , Nov 05 2011 04:35 PM ... My 4WD:RA 07 Rodeo; State:NSW ... would say the reverse switch would be on the gear box some where ...

Locate & Repair 96' Pajero Reverse Light Switch - YouTube

? 1:45
https://www.youtube.com/watch?v=osie5D_m-dA
Nov 12, 2010 - Uploaded by TwoMagadan
Locate & Repair 96' Pajero Reverse Light Switch ... Replacing ABack Up Light Switch On A Manual ...

Dec 14, 2015 | Holden Cars & Trucks

1 Answer

Remove airbag ra rodeo


First disconnect the battery and wate for 3 minutes for all power to drain, then take off the steering cover and then you will see the bolts to remove the air bag, to replace it just do all in reverse, hope this helps

Jul 08, 2014 | 2005 Holden Rodeo

1 Answer

How to install clock spring


Not recomended for untrained people as airbags can be very dangerous. That said you need to. 1) disconect battry 2) remove SRS (Airbag fuse) 3) remove shroud around steering colum 4) wait ten minutes. 5) remove horn pad (airbag houseing) usualy held in by tamper proof bits from back of steering wheel. 6) unplug wires to airbag & horn 7) undo steering wheel bolt & mark position of steering wheel to colum splines. 8) remove steering wheel with suitable puller (NOT a hammer) 9) unclip clock spring & replace 10) reverse procedure

Sep 22, 2012 | Cars & Trucks

1 Answer

Need to remove steering wheel airbag on my 2004 xc90 volvo


Let me start by saying I do not recommend that anyone other than a mechanic attempts this. Airbags are very dangerous to work on and should be left to professionals. If you do choose to do this yourself, take your time and be careful.

On the back side of the steering wheel there are access holes to the screws which hold the airbag in place. Before attempting anything involving an airbag, make sure to disconnect the battery and leave it disconnected for at least an hour to be safe. The required time to deactivate the airbag is less but please be safe. I don't remember the size but the bolts are torx. Once you remove them the airbag assembly will slide right out. Behind it is the ribbon cable attaching it to the steering wheel. Be very careful when removing this as to not damage the clock spring or the wiring. Good luck and please be careful.

Aug 31, 2011 | 2004 Volvo XC90

2 Answers

00/01 Pontiac Bonneville. How do we get off the steering wheel?


Get a repair manual such as Haynes or Chiltons at a auto parts store to walk you through. Once you get the horn button off you will need a steering wheel puller. They sell them too.
I hope my suggestions helps and all the luck to you.
burdfrenzy
http://stores.ebay.com/Pittsburgh-Joes-Pants-Nat

Dec 23, 2010 | 2001 Pontiac Bonneville

1 Answer

How to take of stearing wheel of bmw


There will either be two torx bolts behind the steering wheel spokes to release the airbag or in the same place there will be a hole on either side where a flat head screwdriver can be inserted to push a spring clip off a securing clip. Remember to disconnect the battery before touching the airbag. Once the airbag is removed you will easily be able to undo the bolt that retains the steering wheel.

Mar 26, 2010 | 1996 BMW 318

1 Answer

I cannot figure out how to pull the steering wheel off of my 96 honda accord


Read this carefully, in total, before you begin.

With car wheels aimed straight ahead, disconnect the neg. battery terminal (if you have an anti-theft radio, make sure you have the code, because you will need it.)

Wait three minutes before proceeding to allow the airbag’s backup power supply to be depleted.

Remove the access plate from the lower steering column cover and remove the short connector from the access plate (the short connector is stowed on the inside of the access plate. It is a little device that is used especially for this purpose)

Unplug the airbag module-to-cable reel connector (yellow) and plug the short connector into the airbag module side of this connection to disable the airbag.

Remove the access panels from each side of the back of the steering wheel cover, then remove both of the torx screws (you’ll need a torx screwdriver) that retain the airbag module to the steering wheel.

Pull the module off the steering wheel and CAREFULLY set it aside with the trim side facing up.

Unplug the electrical connector for the horn, and, if you have it, for the cruise control.

Remove the steering wheel retaining nut. Paint or scribe a mark indicating the relationship of the steering wheel hub to the steering shaft.

Remove the steering wheel with a steering wheel puller. DO NOT turn the steering shaft while the steering wheel is removed. If you do so, the airbag reel could be damaged.

Reinstallation is the reverse of the removal, making sure the cable reel is centered with the car wheels straight ahead (if you haven't moved the shaft, that should not be a problem), and making sure that the locating pins on the steering column engage the holes in the back of the steering wheel. Put the nut back. Torque it (36 ft. lbs). Reconnect horn and cruise control. Replace airbag, tighten torx screws. Reconnect airbag and put short connector back in access plate. Reconnect neg. battery cable.

Hope this helps you.

Feb 05, 2010 | 1996 Honda Accord

1 Answer

Removing and replacing the ignition switch


You will need the following tools:

Steering wheel puller Torx bits (get a set, you need 3 sizes) Inverted Torx ( a set is available at Schucks/Kragen/Checker Screwdriver A few zip ties Wire cutters

Start by disconnecting the yellow wire under the dash for the airbag. Now turn the steering wheel 90 degrees to access the underside of the steering wheel. You will have to insert a smaller size flat blade screw driver into the 4 holes on the back of the steering wheel and rotate them to release the airbag. Now remove the nut holding the steering wheel on and remove the steering wheel. BE VERY CAREFUL WITH THE AIRBAG MODULE!! Now remove the lower column cover with 2 Torx screws. You will now have access to 2 inverted Torx screws that hold the top column cover in place. Look on the top of the ignition cylinder housing and find the small hole. Insert a small Allen wrench into the hole and turn the key to "run" position and the ignition cylinder will come out, now the top cover will come off, giving access to the ignition switch. You will need the smallest inverted Torx bit for the 2 screws that hold the ignition switch in. You will have to cut a couple of zip ties to free the wiring. Now get a Torx bit and a 7mm socket and remove the lower dash panels to get access to the wiring harness. You will need the 7mm to unscrew a bolt that holds the connector together under the dash. Just follow the wiring to see what I mean. Once the connector is loose, you will see two plastic strips that run along side the connector. These are easy to remove and slide off, and are keyed so you cannot reinstall them wrong. Hope this helps.

I was getting frustrated trying to get the air bag off the wheel to do a column change out to a tilt wheel. The above worked perfectly for removing the airbag. However, the inverted torx bits can be removed with a good 6 point socket on a 1/4 inch drive ratchet as well. No need to buy a special tool.

Good luck

Nov 19, 2009 | 2000 Chevrolet Blazer

3 Answers

How replace turn signal switch 2000 chevy blazer?


Since the 2000 chevy blazer is equipped with SRS (Saftey Restraint System), ie: Airbags, which is located in the steering wheel. In order to replace the turn signal switch you must remove the steering wheel. Therefore I would only highly advise you to take it to a dealer to have this done.

Oct 07, 2009 | 2000 Chevrolet Blazer

1 Answer

Headlights not working even after bulbs and fuses replaced


Replace your headlight switch. You need torx bits, a steering wheel puller, and bolts to perform the repair.

Disconnect your negative battery cable and wait at least 1 minute before going any further (this insures your airbags are disabled if your vehicle has them).

Remove the plastic covers that cover the steering colum. If applicable, remove the airbag from the steering wheel; if you don't have a airbag pull the horn switch from the center of the steering wheel. Remove the retaining clip from the center shaft in the steering colum. Remove the bolt that holds the steering wheel, then use a steering wheel puller to remove the steering wheel. Remove the torx screws from the headlight switch, and remove the electrical connectors. Install in reverse.

I hope this information helps you, and I wish you luck on your repair.

Apr 25, 2009 | 1996 Chevrolet Cavalier

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

724 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...