Question about Chrysler 300C

Open Question

Where is the 2005 chrysler 300 cigarette lighter fuse located

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 34 Answers

SOURCE: cigarette lighter fuse location

The cigarette fuse is located in the battery junction box under the hood, it is fuse # 10 and is a 20A fuse, open the hood and find the box it is on the passenger side towards the back of the compartment, it is 10th in line on the top row, also you can check these fuses without removing them through the clear plastic top so that should make things a little easier too, hope this helps

Posted on Nov 14, 2008

Ad
  • 6 Answers

SOURCE: Where is the Fuse for my cigarette lighter

In the junction box, usually to the left of the steering wheel. Labeled (generally) courtesy or cigar.

Posted on Jan 01, 2009

  • 5 Answers

SOURCE: 1999 Oldsmobile Cutlass Cigarette Lighter Fuse

Under the hood directly in front of the driver is a covered fuse block. Remove the cover and the fuse is #34.

Posted on Mar 08, 2009

  • 1 Answer

SOURCE: Cigarette lighter fuse location on Ford Escort ZX2 2002

I had exactly same problem. I could not use my GPS or charge my cell phone.
In front of the driver sit, there are actually 2 fuse boxes. You probably found the first one. A second one is located above well hidden. Once you find it, you'll find the fuse you are looking for.

2d925aa.gif

Posted on Mar 14, 2009

taran_2005
  • 10515 Answers

SOURCE: 2005 Chrysler 300 thermostat location?

Hi,

In your Model :-

The automotive thermostat is a temperature controlled on and off valve. When the temperature rises to a predetermined temperature, the thermostat opens up to allow the engine coolant to flow through the cylinder block and the radiator. This flow is crucial to maintain optimum operating temperature for fuel efficiency, enhanced driveability, and engine protection. The coolant flow is reduced when the engine is cold, and the flow is increased when the engine is hot. Contrary to popular opinion, operating the vehicle without the thermostat doesn't make the engine run cooler. It will actually run hotter because there isn't a thermostat to slow the coolant flow. This means the coolant doesn't stay in the radiator long enough to dissipate its heat.

TO TEST THERMOSTAT

There are several ways to test the opening temperature of a thermostat.
One method does not require that the thermostat be removed from the engine.

  • Remove the radiator pressure cap from a cool radiator and insert a thermometer into the coolant.
  • Start the engine and let it warm up. Watch the thermometer and the surface of the coolant.
  • When the coolant begins to flow, this indicates the thermostat has started to open.
  • The reading on the thermometer indicates the opening temperature of the thermostat.
  • If the engine is cold and coolant circulates, this indicates the thermostat is stuck open and must be replaced.
The other way to test a thermostat is to remove it.
  • Suspend the thermostat completely submerged in a small container of water so it does not touch the bottom.
  • Place a thermometer in the water so it does not touch the container and only measures water temperature.
  • Heat the water.
  • When the thermostat valve barely begins to open, read the thermometer. This is the opening temperature of this particular thermostat.
  • If the valve stays open after the thermostat is removed from the water, the thermostat is defective and must be replaced.
  • Several types of commercial testers are available. When using such a tester, be sure to follow the manufacturer's instructions.
  • Markings on the thermostat normally indicate which end should face toward the radiator. Regardless of the markings, the sensored end must always be installed toward the engine.
  • When replacing the thermostat, also replace the gasket that seals the thermostat in place and is positioned between the water outlet casting and the engine block.
4fa3f4e.jpg


Positioning a thermostat into an engine.
  • Generally, these gaskets are made of a composition fiber material and are die-cut to match the thermostat opening and mounting bolt configuration of the water outlet.
  • Thermostat gaskets generally come with or without an adhesive backing. The adhesive backing of gaskets holds the thermostat securely centered in the mounting flange, leaving both hands of the technician free to align and bolt the thermostat securely in place.

TO REPLACE THERMOSTAT

CAUTION
If the radiator is filled to the top with coolant and the engine is run without the radiator cap in place, the coolant will expand and spill over as the engine warms up.
  • Drain some coolant into a clean container until the coolant level is below the thermostat housing.
  • Remove the upper radiator hose connection from the thermostat housing.
  • Loosen the housing bolts and remove the housing.
  • Remove the gasket and scrape it carefully from the surface of the housing and the mounting surface on the engine. If the gasket remains on either of the surfaces, there will probably bea coolant leak after reassembly. Some engines use a rubber O-ring to seal a thermostat housing.
  • Compare the size of the thermostat to the old one. They are of different sizes, types, and temperature ratings.
  • The temperature rating is stamped on the sensing bulb on the bottom of the thermostat. The temperature bulb faces the block.
  • When replacing a thermostat, be sure that the thermostat fits into the groove in the block or outlet housing. If the thermostat is installed upside down, the engine will overheat.
  • Install the gasket.
  • Reinstall the thermostat housing. Refill the system and run the engine or pressure test to check for leaks.
  • When the engine has reached operating temperature make sure the thermostat opens.
  • You should be able to see coolant circulating within the radiator.
  • Another way of checking thermostat operation is to feel the top of the radiator hose or use a thermometer or multimeter with a temperature probe to confirm that the coolant is warming up.
  • If the engine is overheating, but the top hose is still cool to the touch, the thermostat is stuck closed and must be replaced.
NOTE When a paper gasket is used and the recess is in the thermostat housing, it is a good practice to position the thermostat into the recess and glue the gasket to hold it in place. If it falls out of its groove during installation, the outlet housing can be cracked or a coolant leak will result. Before tightening the water outlet housing, try to rock it back and forth to be sure it is flush. Housings are often cracked during this step.

Hope i helped you.

Thanks for using ' Fixya ' and have a nice day!!



Posted on Oct 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is radio fuse for 2005 malibu classic


there is a fuse at the back of the radio , remove the radio and replace fuse

May 10, 2014 | 2002 Chrysler Town & Country

1 Answer

2006 chrysler 300. Where is the fuse for cigarette lighter?


The fuse for the lighter is fuse # 18 in the power distribution center. It is a 20 amp fuse. The power distribution center is the fuse box in the trunk. Fuse 20 is in the row of fuses

Apr 12, 2014 | 2006 Chrysler 300

2 Answers

Which fuse controls the cigarette lighter and radio, mine are not working


In the integrated power module, find 20A fuse 5. Replacing it should get both the cigar lighter and radio operating again

Oct 12, 2012 | 2005 Chrysler Town & Country

2 Answers

Hello and thank you. There is no power coming from the Cigarette Lighter (power Outlet as listed in the manual) of my 2006 Chrysler 300 Touring. I have searched both fuse boxes of the vehicle and can not...


Fuse is located under the spare tire well and is in the fuse panel and is an 20 amp fuse that is slightly misaligned on the middle row of the box. This will fix cigarette lighter in ash tray in lower middle cluster of radio and a/c.

May 15, 2010 | 2006 Chrysler 300M

1 Answer

Fuse


CHANGE THE AUX fuse

Aug 25, 2009 | 2005 Chrysler 300

1 Answer

Ashtray lighter does not work, the manuel does not show fuse.


ashtray lighter and console lighter don't work, where is the fuse located and number?

Jun 19, 2009 | 2005 Chrysler 300

1 Answer

Which is my fuse for my car lighter on the fuse box 2005 chrysler 300


It should be labeled on the fuse box cover. Check Your owners manual also.

May 24, 2009 | 2005 Chrysler 300

1 Answer

Chysler 300tour


if it isnt located under the dash or in glove box check when you open dricer door and look on side of dash if not there then its under hood

Jan 25, 2009 | 2005 Chrysler 300

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

119 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

chargerhp
chargerhp

Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...