Question about 1995 Jeep Cherokee

Open Question

How do I remove the front skid plate from a 1995 Jeep Cherokee?

Posted by on


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

  • 6982 Answers

SOURCE: crankshaft removal of a 1995 jeep cherokee 2.5td

To remove crankshaft, engine must be removed from vehicle. It is bolted to the flywheel/flex plate of your transmission. Even if you found a way to remove it, it would be really difficult to replace it correctly. If you are going to replace it due to a bearing failure, keep in mind that debris from that failure likely has migrated into oil galleys and is waiting there to damage new bearings. At the very least all passages should be blown out with high pressure air, preferable is to strip engine down and also check cam bearings which may also be worn from pressure loss during failure and debris.
good luck!!

Posted on Apr 24, 2009

  • 54 Answers

SOURCE: remove front wiper arms. Lift arm, slide out

Just pry them off. Make sure the tab is out the whole way. Sometimes they can be tough to get off. Spray with wd40 it should aid in getting it loose. You could even tap it a few times with a rubber mallet or a light hammer, just be careful. Good luck if this helps let me know.

Posted on Jun 19, 2009

  • 6982 Answers

SOURCE: how do you remove the shifter know on a 1995 jeep

from what I remember, the handle just pulls straight up. I do suggest that you only do this when it's not cold out....the plastic is brittle and if you need to re-use it you may break it. If necessary put hot rags over it to warm it up.

Posted on Apr 07, 2010

  • 707 Answers

SOURCE: On a 2004 Jeep Grand Cherokee 4x4 with a 4.7 H.O.

Not as far as i know. But if u can't get it from top or bottom the skid plate is an easy removal. Hope this helps.

Posted on Aug 11, 2010

  • 95 Answers

SOURCE: how do you remove the

Use white paint, chalk or a scribe to mark the relationship of the front U joint to the front diferential pinion yoke. Mark the relationship of the rear U joint flange to the transfer case companion flange. Unbolt the front end of the drive shaft from the pinion yoke and the rear end from the transfer case companion flange and remove the drive shaft from the vehicle.
hope thei info helps.

Posted on Feb 24, 2011

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

Need skid plate

Try these web sites:,make,MERCURY,year,1995,d,1995_MERCURY.html

Jan 20, 2013 | 1995 Mercury Grand Marquis

1 Answer

On a 2004 Jeep Grand Cherokee 4x4 with a 4.7 H.O. engine do you have to remove the front skid plate to access the oil filter for changing? Thanks in advance.

Not as far as i know. But if u can't get it from top or bottom the skid plate is an easy removal. Hope this helps.

Aug 11, 2010 | 2004 Jeep Grand Cherokee

2 Answers

My jeep cherokee sport will not start. lights come on but nothing else. battery and terminals are good. im sure its the starter. how do i replace this?

try putting it in neutral & see if will start,,if not,,find starter & tap on the bottom case of it then try it again,,if still nothing,,if u have not done this before,,get a haynes repair book for your jeep,,it will help u,,

Apr 18, 2010 | 1993 Jeep Cherokee Country

1 Answer

Oil cange/ filter change

Filter is located in the front of the engine right near the crank pulley, drain plug is a 13mm plug up underneath the skid plate

Apr 04, 2010 | 2002 Jeep Grand Cherokee

1 Answer

I cannot find my oil pan. I have a 2005 jeep

jeeps are good for having skid plates to protect the under belly of the engine removing it should let you see the oil pan

Feb 24, 2010 | 2005 Jeep Grand Cherokee

1 Answer

I have to replace door on my 1995 jeep grand cherokee. Im wondering how do i remove the electrical conection between body and door.

You should find a plug in behind the kick plate where your left foot goes. Unplug it, and feed it through the door jam.

Jan 07, 2010 | 1995 Jeep Grand Cherokee

1 Answer

I have a 2002 jeep wrangler x model. what holds the transmission in place. is it the skid plate?

mounts hold the tranny in place also its bolted to the motor,skid plates are only to protect from damage if you were to go off road with it.the skid plate can be removed and disposed of if you wanted its useless if you dont do the off road people like them for show as well i have all chromed out skid plates on mine

Dec 23, 2009 | 2002 Jeep Wrangler

1 Answer

How do you get the starter off

The starter is on the right side of the engine, at the same place the transmission is located. Remove the neg. battery cable first, on 4WD models remove the front axle skid plate ( if equipped with), then disconnect the wires from the starter, disconnect any clips that hold the wiring in position, remove the mounting bolts from transmission side. It may be easier to disconnect the wiring after the starter is removed from the engine. Make sure to keep the starter supported and do not allow to hang by the wiring.

Oct 16, 2009 | 1993 Jeep Grand Cherokee

Not finding what you are looking for?
1995 Jeep Cherokee Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts


Level 3 Expert

79186 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides