Question about Suzuki Cars & Trucks

Open Question

Where do you check clutch fluid in suzuki samurai 1987

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 25 Answers

SOURCE: 87 samurai bolt torque specs for engine

The haynes book is not recommended since there are numerous mistakes and they still will not update. One of the biggest is the firing order.

The factory service manual is the only way to go.

Head bolts - 46 - 50.5 lbs (there is an order sequence for the bolts)

Intake & exhuast manifolds- 13.5 - 20 lbs

Flywheel - 41.5 - 47 lbs

Clutch cover - 13.5 - 20 lbs

Posted on Mar 17, 2009

Ad
  • 4 Answers

SOURCE: 1987 Suzuki Samurai Clutch problem.

The last time this happened to me, the clutch cable had worn through the out cable housing and had to be replaced.

Posted on Apr 06, 2009

  • 14 Answers

SOURCE: 1987 Suzuki Samurai alternator wiring. No original wire harness

yes the b goes to the battery.

http://bbs.zuwharrie.com

heres the site for you.. we have all the answers.

http://www.acksfaq.com/diagram_color_86-88_sam.htm

i drew this up a while back. it could help you out alot.

Posted on Apr 22, 2009

  • 14 Answers

SOURCE: Ignition wiring circuit - 1987 Suzuki Samurai

http://www.acksfaq.com/faqsearchresults-.php

Posted on Apr 23, 2009

  • 880 Answers

SOURCE: Height of Clutch Pedal

It sould engage about 2 1/2 inches from the floor board.

Posted on Mar 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1987 Suzuki samurai take 30 minutes to start in the morning only the it start OK for the day seems like it not getting gas in the morning only


the G13 or G16 engine, and 1987 year was carbs, not EFI.
so if it has carb , you need to say so.

if it starts fast with test fuel (spray)
then your choke is dead.
ever adjust a choke before.
RTM?

https://suzukipitstopplus.com/Products/10163-1986-1987-samurai-service-manual.aspx

Mar 29, 2016 | 1987 Suzuki Samurai

1 Answer

What are the 1987 suzuki samurai stock carburetor settings


carbs are tuned for you altitude. (what country?)
is car still stock, many are not. not this old.
and to tune it takes a 5 Gas Analyser or AFR meter.
once tuned , the Cat converter cleans up the retainer,
the full manual is here, for USA.
http://www.acksfaq.com/sitemap.htm

May 29, 2013 | 1987 Suzuki Samurai

1 Answer

1987 samurai rolls when off and in gear


Check the drive shaft first, ok, then the input shaft or main shaft inside the ****** is broken.

Oct 19, 2012 | 1987 Suzuki Samurai

1 Answer

My speedometer isn't working on my 1987 Samurai Suzuki


Check vehicle speed sensor or wiring,check engine light should be "on".If light not on bad speedo head in dash.If cable driven[unlikely] check for a broken cable from trans to dash.

Apr 17, 2010 | 1987 Suzuki Samurai

1 Answer

1986 suzuki samurai clutch doesn't disengage


throwout bearing possibly, how does the clutch pedal feel?

Apr 03, 2010 | 1987 Suzuki Samurai

2 Answers

Height of Clutch Pedal


I assume it is a cable operated clutch. If so the adjustment is tightened so that there is about 1/2 to 1" of pedal travel to clutch operation, provided the gears can be selected smoothly.

Mar 09, 2010 | 1987 Suzuki Samurai

2 Answers

How hard is it to rebuild an 86 Suzuki Samurai 5 speed transmission? I have a tranny tech telling me I need a clutch, flywheel resurface and a remanned unit. How hard could it be. Not 1800$$$! That's Hard....


ITS NOT A HARD JOB. BUT YOU HAVE TO BE CAREFUL.YOU ARE WORKING UNDER A CAR. BESURE TO USE JACK STANDS .YOU NEED A REPAIR MANUAL.IT SHOW YOU HOW TO REMOVE TRANSMISSION.YOU HAVE TO SUPPORT ENGINE WHEN MOVING TRANNY.REBUILT KITS.WILL HAVE ALL GASKETS SEALS AND BEARINGS.BUT MAJOR PARTS YOU HAVE TO BUY THEM SEPERATE.LIKE SHIFT FORK COUNTERSHAFT AND SYNCHRONIZERS.NOW THE CLUTCH KIT IT WILL HAVE CLUTCH PRESSURE PLATE AND CLUTCH RELEASE BEARING.BESURE WHEN YOU BUY KIT MAKE SURE CHECK IT.MAKE SURE IT HAS EVERYTHING YOU NEED.

Jul 22, 2009 | 1987 Suzuki Samurai

1 Answer

1987 suzuki samurai distributor problem


check your plugs...one might be faulty or installed wrong.

Jun 17, 2009 | 1987 Suzuki Samurai

2 Answers

I have a 1988 suzuki samurai and it has a noisy drivetrain and also how do you check the transmission fluid it does not have a dip stick and i cant find a plug on the side


The transmission doesn't have a dipstick but it does have a fill level plug located at the rear of the extension housing, just to the passengers side. It is a round plug with a 3/8 square hole in it.
Fill trans till oil overflows out of this hole.
Use VMX80 or similar.

Apr 25, 2009 | 1987 Suzuki Samurai

2 Answers

1987 Suzuki Samurai Clutch problem.


Adjusted Clutch cable assembly under passenger side of vehicle. Had assistance from friend depressing clutch pedal and engaging shift lever. Problem went away

Mar 18, 2009 | 1987 Suzuki Samurai

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...