Question about 2008 Buick Lacrosse

Open Question

How to remove floor console 2005 buick lacrosse to change light

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: how do you add power steering fluid. 2005 buick lacrosse

It is very hard to see, its back and underneath the altenator, use a flashlight to find it buried under wires and tubes.

Posted on May 03, 2009

Ad
  • 192 Answers

SOURCE: lowbeams headlamp won,t work on 2005 buick

Start simple. Investigate your fuses, since it is unlikely, but not unheard of, for both low beams to fail simultaneously.

Do you know where your fuses are?

Posted on Aug 17, 2009

  • 7353 Answers

SOURCE: how do i change the low-beam bulb on my 2005 buick

there should be 2 brackets at the rear of bulb housing, 1 may have a small bolt.....lift these up and the headlamp housing should come out. you will see how it works when you get it apart.

Posted on Oct 09, 2009

  • 6 Answers

SOURCE: My remote won't start my 2005 Buick LaCross. I

Both my remotes no longer work. I will be ordering new ones off Ebay and having my dealer program them. New ones from Buick are very pricey.

Posted on Oct 20, 2009

  • 3 Answers

SOURCE: how to install/change complete headlight assembly

Buick Lacrosse - The bright light fitting is the same as the dim so take it apart first to see how the cover screws off/on and the light comes out. Both the cover and the bulb are removed by a standard twist to the counterclockwise and replaced by a twist to the clockwise. Now to the dim light. You have to release the entire light assembly before you can remove the screw-on cover to reach the light. On the rear edge of the light unit closest to the engine is a white locking tab. Pull that tab up just to the point where it releases…pull too far and it locks again. Next, locate the other locking bracket which is a metal bracket in the center-rear of the light assembly. This bracket is held down by a screw. Remove the screw with a 10mm wrench. Lift the bracket just like you did the white bracket. You should now be able to pull (or pry) the entire light unit forward a little. Depending on the size of your hands this might be enough. If not, then you need to release the plastic bumper assembly to give you a little more space. This is done by removing two expansion locking pins, one that holds the little plastic strip down between the bright and dim lights and one that is located inside a rubber bumper on the engine side of the light unit. To remove these locking pins, pull or pry up the little tab in the center of the pin just like you were pulling a nail by the head. That should give you more space.

Posted on Apr 03, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2009 buick lacrosse console gear indicator bulb


Transmission Floor Shift Control Indicator Lamp Replacement

Remove the front floor console. Refer to Front Floor Console Replacement.
Rotate the floor shift control indicator lamp socket (2). Pull the socket from the trim bezel.
Remove the bulb from the socket.

Front Floor Console Replacement

Preliminary Procedures
Remove the rear floor console. Refer to Rear Floor Console Replacement.
Remove the instrument panel lower trim plate. Refer to Instrument Panel Lower Trim Plate Replacement.
Set the parking brake, then shift the transmission into drive and push the shift indicator down until it locks, to allow clearance to remove the console.
1
Front Floor Console Screw (Qty: 2)
Caution: Refer to Fastener Caution in the Preface section.
Tighten
2 N·m (18 lb in)
2
Front Floor Console Bolt (Qty: 2)
Tighten
10 N·m (88 lb in)
3
Front Floor Console Assembly
4
Front Floor Console Retainer Clip (Qty: 2)

Feb 24, 2017 | 2009 Buick LaCrosse

3 Answers

One high beam not working 2006 Buick lacrosse


Sampson, sounds like a bunt out bulb, which will need changed.
If you feel comfortable doing it yourself. Basically three screws, and you have to pull one plastic fastener from the fascia (bumper) and pull the bumper back a bit, and pull the assembly out. I believe it is in the manual, not bad to do. I will post a link to tell or show you how to do it. Press the helpful button

Headlight Change 2005 2009 Buick LaCrosse 2006 Buick LaCrosse CX 3 8L V6

2008 Buick LaCrosse Headlight Replacement

Thread how do replace the headlight bulb in 2005 buick lacrosse

Headlight Bulbs

Feb 13, 2016 | Buick Cars & Trucks

1 Answer

How to change a heater core in a 2005 Buick Lacrosse


You should not have to pull the whole dash. Take the plenum apart, loosen the hose clamps, remove the core.

Dec 16, 2014 | 2005 Buick LaCrosse

1 Answer

How do you change the brake light on2005 Buick


remove the two black plugs by the hatch opening and you will see two small bolts. Remove them and the light comes out.

Oct 11, 2014 | 2005 Buick LaCrosse

1 Answer

2005 buick lacrosse engine stalls when gas cap removed


sounds like an issue with either your carbon filter or purge solinod being blocked

Jul 18, 2012 | 2005 Buick LaCrosse

1 Answer

How do remove headlight assembly on 2005 Buick LaCrosse to replace lighe bulb


I just changed the low beam bulb in a '05 Buick LaCrosse and found it really rather easy after researching it. I found no reason to remove the grill and the bumper cover, BUT you do have to remove the top 4 fastners that hold the grill assy to the radiator support, then you can work the headlight assy forward enough to work it out of the socket and turn it down so you can get to the bulb pockets on the back side. NO NEED to remove it all, just loosen it and gentley pry things forward enough to get the light assy out. ALSO> My supplier said his Wagner lighting book called for a 9006 bulb, but the car I worked took a H11. About 4x the money over a plain ol 9006 bulb but it might save someone picking up the wrong bulb. I hope this helps someone else out....Best of luck to you all

Sep 07, 2010 | 2005 Buick LaCrosse

1 Answer

How do you change a tail light in 2005 Buick


I have a 2002 lesabre and suspect it is the same. The light assemblies are bolted to the car from the inside of the trunk. Mine has three sections. Left side of trunk, across the back of the trunk and right side of the trunk. Open the trunk and look thru the small holes in the back for nuts that hold on the sections. They may require a deep socket to reach. Also not all the nuts need to be loosened. Trial and error. Once the nuts are removed the light assemble is freed from the car. Don't let it fall and scratch the car. The wires will help hold it in place. The light holders usually turn/twist and pull out. A little bit of a pain, but not too difficult. Again the deep sockets are probably required.

Apr 25, 2010 | 2005 Buick LaCrosse

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...