Question about 1987 Chevrolet Camaro
Replaced column nothing works
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
you need to replace the electrical part of switch?If os it is down on column under dash will be two bolts holding on with the dimmer switch also
Posted on Aug 28, 2008
SOURCE: Short in steering column wiring
torque bit 20 to remove the air bag bolt in the back cover stering puller stering puller to push plate phillip screw driver that about it pierre
Posted on Oct 19, 2008
The replacement of a steering column is easier than you think, and you can do it without a book or diagrams. First, head off to your favorite junkyard and scout up a truck that is similar to yours in year, make and model. This way, you are assured to have a piece that slips right in. Take the column out of the junker before you try to take the one out of your truck. Open the hood and you will see the column shaft just sitting there, and separate the column from the steeering box. Typically, it can be a slip joint with a single bolt to tighten it up on the steering box shaft, but you could also see a canvas/rubber flex joint with four bolts coupling the shaft components. You might have to squirt the bolts with panther **** (WD 40, etc.) in order to get 'em loose. Under the dash, you'll see a long flat plugin for the wiring harness that comes from the bottom side of the column. Unplug that and remove the cover under the dash that hides the two nuts that hold the steering column mounting yoke. Pull back the carpet at the spot on the floor where the column goes throiugh, and you will see a rubber gasket of sorts that has four or five small screws holding it to the floor. If a part of the wiring harness is in the way of you dropping the column down and out, look for the plugin that connects it and get it out of the way. DO NOT PULL VERY HARD ON THE WIRES! If the truck didn't have tilt wheel when you bought it, you can get a tilt column out of the junker that can make your day a bit brighter. Remove the column out of the junker, first. Experience is always the best teacher, and the junker will show you how to go about putting the replacement column in your truck. If the truck has an automatic tranny shifter on it, all you have to do is pull a pin from the column, directly in front of the truck's firewall. I have done numerous column swaps and have never needed a book or diagram to do it, and neither will you. If a man can build it, another man can generally fix it or replace it. Remember to start out with the junker, first and foremost, and you can count on the job taking you (as a first timer) about two to two and a half hours. Take your time, pay attention, use your good eye, and enjoy yourself. Ain't nothin' scary about this job. Relax. The truck will actually show you what it take and how to do it.
Posted on May 31, 2009
Tips for a great answer:
Jul 20, 2016 | 1998 GMC Sierra
Feb 14, 2012 | 1987 Chevrolet Camaro
Jul 24, 2011 | 1992 Chevrolet Camaro
Sep 08, 2010 | 1991 Ford Mustang
Jul 03, 2010 | 1999 Chevrolet Camaro
Mar 22, 2010 | 1991 Chevrolet Camaro
Feb 17, 2010 | 1995 Chevrolet Camaro
May 22, 2009 | 1984 Jeep CJ7
May 03, 2014 | 1987 Chevrolet Camaro
Nov 28, 2012 | 1987 Chevrolet Camaro
61 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: