Question about 2001 Chevrolet Cavalier

Open Question

Torque sequence on head bolts 2000 Chevrolet cavalier

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 135 Answers

SOURCE: the torque pressure on 2000 chevrolet bolts on the cylender heads

most are 65 foot pounds ,that is what i say it is . gm on v8 engines are same ,head bolts are 65 and hope this it some help,thanks robert b.

Posted on Jun 27, 2009

rutherford_m
  • 63 Answers

SOURCE: head bolt torque specs and sequence for early 350 malibu motor

There are two different torque specs for this engine depending on which bolts you are torquing. This engine uses three different length bolts, the two sets of longer bolts can be torqued to 70 foot pounds, the short set of bolts that go along the bottom of the head should be torqued to 65 foot pounds. Head surface and block surface should be clean, straight and the a new head gasket should be used.

An easy way to guide yourself in the proper sequence is to make a cheat sheet of sorts. Take the headgasket and piece of cardboard about the same size. Using the headgasket as a template, mark each of the bolt holes on the cardboard with a sharpee marker, pencil or pen. Also outline the headgasket and mark the top of your drawing. Now starting from the center bolt as number 1, move either to the right or left, up or down to the next bolt hole and mark that as number 2. Now move to the bolt hole diagonally across from number 2, past Number 1 and mark it as number 3. Continue this sequence of moving diagonally back and forth across the headgasket outline until all of the bolt holes are marked with a number. What you are trying to do is start at the center of the head tightening it down in steps of about 15 foot pounds moving out from the center.

I have built a lot of these engines over the years and they are very forgiving of the head torquing sequence. As long as you start at the center and move out left and right, up and down alternating back and forth, you will have no problems. As a final check once you are done, check the torque on each head bolt to make sure you have not missed one. This does not have to be done in any sequence and you will then be sure that you have it completed properly. Good luck.

Posted on Apr 27, 2010

  • 335 Answers

SOURCE: cylinder head bolt torque chevrolet 3.4

here is the troque spec for the cylinder heads.

Cylinder Head Bolt

  • First Pass
60 N·m
44 lb ft
  • Final Pass
95 degrees
Cylinder Head Bolt
  • First Pass
60 N·m
44 lb ft
  • Final Pass
95 degrees


Cylinder Head Bolt
  • First Pass
60 N·m
44 lb ft
  • Final Pass
95 degrees
first pass 44 ftlbs
second pass 95 degrees

Posted on Jun 19, 2010

  • 3640 Answers

SOURCE: i need the engine torque specs for 99 chevy malibu

99 chevy malibu v6 3.1 engine, head bolt torque is-- 98 through 2001 is step1- 37 foot lbs, step 2- rotate an additional 90 degrees (1/4 turn). the rocker arm bolts are 168-in. lbs.

Posted on Sep 07, 2010

  • 95 Answers

SOURCE: 1997 cavalier head gasket replacement with a 2.2.

Go onto Autozone.com and sign up for their online repair. It is free to use but you have to register.

Posted on Dec 03, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Please explain on a 96 cavalier 2.2 it say to torque heads 90 degress?


You are referring to the cylinder head bolt-torque sequence. Here is the instructions, then I'll clarify.

  1. Install cylinder head bolts finger-tight. New cylinder head bolts are recommended.
  2. Tighten bolts in sequence, tighten the long bolts to 46 ft. lbs. (63 Nm) plus 90 degrees. Tighten the short bolts to 43 ft. lbs. (58 Nm) plus 90 degrees.

The cylinder head is made of aluminum. Over-torque of bolts can result in warping or cracking of the head. Also, some of the head bolts go into the water jacket. Those bolts requires a teflon sealer or water will come up through the threads and result in coolant leaks. Use a thin wood dowel to probe the cylinder head bolt holes to see if they bottom out or go into the water jacket.

When you tighten the bolts, do it in the sequence directed, up to the toque specified for each length bolt. Once that has been done, you will make one more circuit of the bolts, tightening each one by 90 degrees. The easy way to do this is to place your torque wrench on a bolt with the handle pointed at 6 o'clock. Tighten the bolt another 90 degrees, or when the handle reaches 9 o'clock. 90 degrees is 1/4 revolution of the bolt. (You can start the wrench anywhere that is convenient to make the 90 degree advance without interruption.)

Hope that helps!

Nov 14, 2013 | 1996 Chevrolet Cavalier

1 Answer

Head bolt sequence and torque values on a 1999 Chevy 3.1L engine


if the 8th number om your VIN is a "J" then this is the correct prossess 3.1LTorque sequence --------- ' 6 2 3 7 ' ' 5 1 4 8 ' --------- Step 1: torque in sequence to 37 Ft/Lbs Step 2: turn an additional 90 degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.Always coat bolt threads with the proper sealant.

if the 8th number on your VIN is a "M" then this is the correct prossess 3.8LTorque sequence --------- ' 6 2 3 7 ' ' 5 1 4 8 ' --------- Step 1: torque in sequence to 37 Ft/Lbs Step 2: turn an additional 90 degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.Always coat bolt threads with the proper sealant.

Oct 12, 2011 | 1999 Chevrolet Malibu

1 Answer

I have a 1997 Chevy Cavalier and i'm tryin to torque the head down. I need to know the pattern sequence


The sequence is pretty much the same for ANY cylinder head. Start with the bolts in the center and work your way left, then right, then left, etc. toward the ends.

Feb 01, 2011 | 1997 Chevrolet Cavalier

2 Answers

1997 cavalier head gasket replacement with a 2.2. Also need the torque specs and sequence for the head bolts


Go onto Autozone.com and sign up for their online repair. It is free to use but you have to register.

Nov 16, 2010 | 1997 Chevrolet Cavalier

1 Answer

I need the torque sequence for a 1998 chevy cavalier head


There's two engine's, your car could have, 2.2L or 2.4L. so here's both, cylinder head torque for 2.4L engine.
Step # 1
Bolt's 1 - 8 40 Ft.Lbs
Bolt's 9 - 10 30 Ft.Lbs

Step # 2
All bolt's additional 90deg.

Hope this was very helpful.

cb3ba1f.gif
9568cea.gif

Sep 02, 2010 | 1998 Chevrolet Cavalier

1 Answer

Engine torque specs for 1996 chevy cavalier 2.2l


For 1996 Chevrolet Cavalier 2.2L SFI OHV 4cyl the check the next Head Bolt Torque sequence...

------------ front | 8 4 1 5 9 | of | | engine | 7 3 2 6 10 | ------------

Step 1: torque long bolts 8,4,1,5, & 9 to 46 Ft/Lbs torque short bolts 7,3,2,6, & 10 to 43 Ft/Lbs
Step 2: torque all bolts an additional 90 degrees Recheck final torque in sequence

*** CAUTION *** engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque.

Hope helps (remnember rated this).

Jul 15, 2010 | 1996 Chevrolet Cavalier

1 Answer

Torque and tightening sequence for 1999 2.2 chev


Cylinder Head Bolts

Step 1
Head Bolts A 46 (62)
Head Bolts B 43 (58)

Step 2 Additional 90 Degrees

Tightening Sequence:
http://www.anubiscycle.com/fixya/99cavheadsquence.png

Jan 17, 2010 | 1998 Chevrolet Cavalier

1 Answer

Blown head gaskit need to remove head and replace with new ong


2.2L (VIN 4) Engine
  1. Before servicing the vehicle, refer to the precautions section.
  2. Relieve the fuel system pressure.
  3. Drain the cooling system.
  4. Remove or disconnect the following:
    • Accessory drive belt
    • Air cleaner outlet duct
    • Engine mount
    • Intake manifold
    • Exhaust manifold
    • Engine Coolant Temperature (ECT) sensor electrical connector
    • Power steering pump
    • Radiator inlet pipe
    • Spark plug wires
    • Rocker arm cover

    NOTE Whenever valve train components are removed, keep them in order for installation purposes.

    • Rocker arms and pushrods
    • Lifters
    • Alternator rear brace and the alternator
    • Power steering pump
    • Radiator inlet pipe
    • Ignition coil assembly
    • Accessory bracket
    • Spark plug wires
    • Cylinder head bolts

    WARNING Two sizes of bolts are used; note the location of each.

    • Cylinder head
  5. Inspect the cylinder head and block surface for cracks, nicks, heavy scratches and flatness.
b9d2546.gif
Cylinder head torquing sequence—2.2L (VIN 4) engine

  1. Install or connect the following:
    • Cylinder head with a new gasket and new cylinder head bolts. Torque the long bolts, in sequence to 46 ft. lbs. (63 Nm) and the short bolts to 43 ft. lbs. (58 Nm) plus an additional 90 degree turn on all the bolts.
    • Lifters
    • Pushrods and rocker arms. Torque nuts to 22 ft. lbs. (30 Nm).
    • Rocker arm cover. Torque the bolts to 89 inch lbs. (10 Nm).
    • Spark plug wires
    • Accessory bracket
    • Ignition coil assembly
    • Radiator inlet pipe
    • Power steering pump. Torque the bolts to 22 ft. lbs. (30 Nm).
    • ECT sensor electrical connector
    • Exhaust manifold. Torque the nuts to 118 inch lbs. (13 Nm).
    • Alternator. Torque the bolts to 37 ft. lbs. (50 Nm).
    • Intake manifold. Torque the bolts to 17 ft. lbs. (24 Nm).
    • Engine mount. Torque the bolts to 55 ft. lbs. (75 Nm).
    • Air cleaner outlet duct
    • Accessory drive belt
    • Negative battery cable
  2. Refill and bleed the cooling system.
  3. Start the vehicle and inspect for leaks.

Oct 08, 2009 | 2000 Chevrolet Cavalier

1 Answer

What is the head bolt torque and pattern on a 97 cavalier with 2.2l


I have the information and picture of the sequence and torque values for this if you want it. You have to give me your email and I can send you a picture as I am unsure as to how to post the picture on here.

Aug 09, 2009 | 1997 Chevrolet Cavalier

1 Answer

Heads


These are torque to uield bolts, should be replaced and will come with instruction

Jan 01, 2009 | 1998 Chevrolet Cavalier

Not finding what you are looking for?
2001 Chevrolet Cavalier Logo

Related Topics:

105 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...