Question about Cars & Trucks

Open Question

My combi c20 has the lockout light on, it ran out of oil whilst i was away, now full again, light still on and wont fire up. any help please.

Ran out of oil whilst away so came back filled it but lockout won't go away and won't fire up.

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 21 Answers

SOURCE: clicking sound,low rpm idle, and

If you ever have an oil leak it really should be fixed right away unless this happened all at once. Go to a local mech or if there is an Autozone around go there and have them check the Engine Light code for you for free. You will have more info to work with.

Posted on Jul 31, 2008

  • 52 Answers

SOURCE: e ng lite came on pulled to stop light engine ran

Well it could be a number of problems, check your plugs and leads it sounds one could be dead, oil was low so you could have damaged the bearings and for that you have to get professional help at your ford dealer, timing could be out as well caused by the timing belt skipping a tooth. Have to keep your maintenance regular. Hope this help to solve the problem.

Posted on Sep 21, 2010

Hobbit_who
  • 2044 Answers

SOURCE: I've got a 2003 jetta

If your car is off a single tooth on the Timing Belt, you will have continued problems... you need to verify the timing is on. If the timing is off, reset it and then proceed if the problem returns

I did have a problem with a defective Cam Shaft Sensor and replacing it with another Defective Sensor....

Posted on May 26, 2011

cansmo
  • 2431 Answers

SOURCE: My 2004 Cadillac cts ran low on oil to a small

You should be able to start, what is the fluid level bring it to the recommended level crank it allow the lifter to solidify and compression will build up

Posted on Jun 05, 2011

  • 228 Answers

SOURCE: 2000 nissan maxima won't fire

sounds like it might be flooded. Try and remove the fuel pump fuse from the fuse block that is just in front of your left knee. While it is out crank the car and see if it wants to start and hold down the gas pedal all the way and then relase it and back and forth and once you get it to run have the fuse ready in your hand and in front of the spot to install it. and then keep the rpm's up with the gas pedal until the smoke clears out behind the car.

Posted on Jul 02, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Kia sportage 2.0 cyl 4 misfire after spark plug change valve cover was leaking oil into cylinder ran good for a day now miss fireing again


It will take a while to get rid of all the oil that leaked into the spark plug hole. Take it apart again and recheck.

Feb 28, 2015 | 2002 Kia Sportage

4 Answers

E ng lite came on pulled to stop light engine ran rough and was shaking ck oil was low filled oil ran better this am wife went to take truck to work got to the end of block engine ran rough brought back...


I don't think the rough running had much to do with oil level, since it started running rough a 2nd time. Check the fuel filter and ignition timing.

Sep 20, 2010 | 2002 Ford Ranger Regular Cab

1 Answer

2003 Passat: When I first purchased my Passat it ran fine. It s...


Hi Keith, my collegs are being right but now you have to change tappet cover gasket.That will stop the oil consumption.Change the spark plugs as well.Please.

May 12, 2010 | 2003 Volkswagen Passat

2 Answers

My 1995 gmc suburbans service engine soon light comes on only after i drive on the freeway when i turn the car off than turn it back on the light goes out. i have just changed oil and filter problem began...


hi reset it by disconnecting the live battery connection for3 mins then re connect that has done it for me if this helps please rate it thanks

Nov 21, 2009 | 1995 GMC Suburban

2 Answers

My sons 1990 626 ran great. I change the oil and reconnected the speedometer cable that had vibrated loose. took it for a drive to make sure I didn't have any oil leaks. It ran for about 5 minutes and just...


we'll assume fuel is good..leaving spark and air..and management of systems(computer /sensors)...so the speedo cable was disconnected? try taking it loose again , test drive and report back please

Nov 20, 2008 | Mazda 626 Cars & Trucks

1 Answer

Check Engine light


It sound like you are having a electrical problem.You need to check your electrical/ignition system,not all electrical problem the diagnostic machine can read.

Aug 22, 2008 | 1999 Saab 9-5

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

11 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...