Question about Mitsubishi L200

Open Question

Whats the valve clearance for mitsubishi L200

Just wondered what the valve clearance was for my2004 mitsubishi l200

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
leetamara
  • 702 Answers

SOURCE: my reversing lights dont work how do I change the bulb? Its a Mitsubishi L200

Remove the screws that attach the lense to the truck. Twist the bulb hold from the backside and remove the bulb. Installation is the reverse.

Posted on Jun 12, 2008

Ad
redbeard00
  • 957 Answers

SOURCE: 2001 Saturn L200 start and stall

Have you done any component testing? U1000 is a data issue, cant read pulses per minute. This is usually due to a defective crank sensor but you should do component testing first so you don't replace parts on random. Other reasons for this failure can be faulty ignition switch cam positioning sensor, Blown fuse, bad ground, or ECM.

Posted on Jun 16, 2009

Danniboi
  • 1098 Answers

SOURCE: mitsubishi l200 animal 2006 leaking oil from steering rack

Its most likely a seal on the power steering rack by the age it will most likely just be a seal they are about £7 in UK but possible the rack is goosed although I doubt it, please be careful using the car as it can lock the steering in position, and,,,, well you get it.

Posted on Jan 13, 2010

steve_e_uk
  • 1675 Answers

SOURCE: my mitsubishi l200 is leaning to one side. What

sounds like a broken strut, or suspension spring

Posted on Feb 10, 2010

  • 524 Answers

SOURCE: Hi my electrical engineer disconect my battery's

Hi,

Following may be problem.Please check

1.Check the charge in the battery.
2.The terminals are properly and correctly connected.

Thanx

Posted on Jul 26, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What are the tapped settings


Do you mean valve clearance settings?

May 18, 2016 | Mitsubishi L200 Cars & Trucks

2 Answers

Mitsubishi l200 2.5 did 08 very noisy engine, sounds very tappety is this normal ?


It may be worn out valve lifters that are inside the engine. If you have more than 6,000 miles on the oil, valve lifters could run noisier. Changing to a high mileage type of motor oil may quite down the valve lifters noise somewhat. Synthetic oil used during the summer months could make it noisier too. If you can hear the noise while driving the car, it is not normal. Upon acceleration, if it gets noisier, you will be needing a valve job in the not to distant future.

May 29, 2014 | 2007 Mitsubishi L-200 2.5

1 Answer

Mitsubishi L200


Could be battery.

May 12, 2013 | Cars & Trucks

1 Answer

Valve clearance for mitsubishi L200


Take the rocker cover and the upper timing belt cover off.
Set No 1 Cylinder to TDC - use the markings on the cam spocket to get this - and confirm it's on the compression stroke by check both inlet and exhaust valves are closed and on the heel of the cam.
In this position, check rockers 1,2,4 and 5.
Take care with the feeler guage to make sure you're right under the pad under the adjuster screw properly and completely passing under it, not sticking part way.
Rotate the engine (crank shaft) 360 degrees. This should bring No 4 to TDC - confirm that both inlet and exhaust valves are closed and on the heel of the cam.
In this position, check rockers 3,6,7 and 8.

Clearance for Intake and Exhaust is 0.25mm at normal engine operating temp.

Don't forget to fit a new rocker cover gasket and half moon seal (use something like Hylomar to help make sure the half moon is sealed properly - usual suspect when rocker cover leaks at the back of the engine).

Jan 05, 2013 | Mitsubishi L200 Cars & Trucks

1 Answer

Mitsubishi l200 cuts out


It is probably the Suction Control Valve (SCV), it is fitted on the back of the highpressure diesel pump. I just changed one and it works all fine. The Valve should be around 200 euros on ebay, or about 450 euros at your Maindealer. Universal diagnostics will tell you all kinds of things but not this valve. Don`t know what about the proper Mitsubishi Program.
Good luck

Sep 01, 2012 | 2006 Mitsubishi L200 2.5

1 Answer

L200 paint code,mitsubishi, 2001


Check this link: choosecolor.aspx?make=Mitsubishi&model=L200 or this otger guide in here: MITSUBISHI%20Color%20Information.pdf

Hope helps (remember to rate this answer).

Sep 07, 2011 | Mitsubishi Pickup Cars & Trucks

3 Answers

My mitsubishi l200 is leaning to one side. What


my mitsubishi pajero sport is leaning bad on the left hand side.what could be the problem???

Feb 10, 2010 | Mitsubishi Pickup Cars & Trucks

1 Answer

L200/Triton 1999 v63.0L using oil ok on big trips


HI, this can be caused by a bad rings set or, improper rod bearing clearances as well. The cylinder walls may be worn, due to the bad ring set in this case, in return, causing oil consumption. i would also check Head gasket(s) and, PVC valve as well.

Jul 24, 2009 | Mitsubishi Pickup Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

71 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...