Question about 2010 Audi A6 2.7
Passenger Side Rear Indicator Light needs changing
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Here you will see the left headlight we are going to take out, but the same procedure can be applied also to the right one (click will open a bigger photo in a new window)
First, remove the cover circled in green (just take it, it is not fixed with screws), then, with a Torx screwdriver, remove the two screws circled in red
Under (yes, almost hidden) the cables circled in red and yellow there are two more Torx screws, you don't need to unscrew them all, only make 2 or 3 rounds
Particular of the screws under the circles in the previous photo (sorry for the bad focus)
Last, we have to remove the power connector. To remove it, pull the little plastic block lever circled in green and then, while holding it, pull out the whole connector (in red). After that the headlight is free, and you can take it out from the chassis
Et voila', headlight removed :) Red circles are for the vertical offset control, don't touch them unless you know what you're doing. Lights are located under the black plastic covers
Posted on Mar 08, 2009
Remove the tires, Remove the calaper bolts, (small heads on them 12mm or so) Remove calaper, Pads are setting in a holder. Lube new pads with litheum grease and place in holder. (look at old pads, one or both may have small metel tab on one end) If the new pads have the tab, put that pad where the old pad with the tab was. (ie. tab to the inside) Press pistion in with a 'C' clamp. If it won't go in easly, it may screw in. If the parking brake cable is hooked to the calaper, it probly screws in. Use large pliers to screw in calaper piston. Place calaper over pads and install bolts (lube bolts) Rember to pump brakes befor driving . to get a solid peddle.
Posted on May 20, 2009
remove rear part of air intake duct
take off cover for headlight housing
remove connector (counterclockwise) and wire clamp for bulb
Posted on Jul 13, 2009
SOURCE: Audi TT HID bulb needs replacing
You can change the bulb easily yourself in about five minutes, especially on the passenger side. You may want to disconnect the battery, though I don't know if that is necessary. You may also want to handle the bulbs wearing latex or nitrile gloves so as to not get your skin oil on the glass.
1. Remove the decorative cover that conceals the Coolant reservior. There is a single philips screw near the firewall that holds the cover down.
2. Find the back of the headlight and pull the metal wire clip that holds the back of the headlight cover toward the engine. Remove the cover.
3. Look inside and find the back of the HID bulb--it will be toward the outside fender. Twist the connector until it separates.
4. There is a retainer ring that holds the bulb in. Again, twist that until it comes loose. The bulb should come right out.
5, Put the new bulb in, noticing the notch is on top. Also, attach the retainer ring. It is marked "Top" to help orient it. Reattach the connector with a twist.
6. Make sure everything is firmly in place. Reconnect your battery and test the lights. Finish putting anything else back on.
Posted on Nov 21, 2009
Tips for a great answer:
Jan 26, 2014 | Hyundai Tucson Cars & Trucks
Jan 16, 2014 | 2010 Jeep Liberty
Feb 27, 2011 | 1998 Plymouth Neon
Jul 16, 2009 | 1993 Ford Festiva
Apr 27, 2009 | 2006 Dodge Caravan
Jul 21, 2008 | Audi A6 Cars & Trucks
29 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: