Question about 2001 Chevrolet Tahoe
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Hi. I'm reading your request.
Your S10 . has a small fuse box Next to the battery.
1 - air solenoid 10 amp.
1 - air fuse 30 amp.
1 - Mini relay (air relay)
On under hood main fuse block you have.
1 - fuse Engine E 10 amp.
Posted on Jul 12, 2008
And some instructions
Caution: Allow the engine to cool before servicing the secondary air injection AIR system in order to reduce the chance of severe burns.
1. Remove the clamp from the check valve.
2. Disconnect the AIR hose from the check valve.
3. Remove the check valve from the left side AIR pipe.
4. Remove the left AIR pipe from the exhaust manifold.
5. Before replacing a check valve, test the valve for proper operation.
5.1. Install a vacuum pump to the nipple side of the check valve, AIR pump side.
5.2. Pump the vacuum pump to 10 inches Hg and observe the gauge.
5.3. Replace the check valve if the vacuum bleeds down to zero within 5 seconds.
Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.
1.Install the check valve onto the AIR pipe.
Tighten the check valve to the AIR pipe to 23 N·m (17 lb ft).
2.Connect the AIR pipe to the exhaust manifold.
Tighten the AIR pipe to the exhaust manifold to 20 N·m (15 lb ft).
3. Install the AIR hose to the check valve.
4. Install the check valve clamp.
Posted on Jul 08, 2009
under the radiator on the passenger side of the truck. There is a little splash guard you will need to remove to see it, The guard is held in with 4 15mm headed bolts, then you will be able to see the bottom of the air pump.
Posted on Oct 26, 2009
SOURCE: secondary air injection system
This is a pump that sits underneath your front bumper on the passenger
side. It is about the size of a baseball and has two hoses going into
it. I would suggest you replace it yourself as it would cost you about
$360.00 if you were to go through the dealer.
Water intrusion is what will typically kill these electric pumps. There is a Technical service bulletin (#04-06-04-015) Regarding this problem, according to the tsb, you will need a new pump and there is a hose assy. #12590627) that has you reroute the pump from future water intrusion or it is guaranteed to fail again.
Although I have had water in the pump I did not see any indication of the inlet hose as the cause. It was suggested that the one way metal check valves ($15.00) that mount to the rt & lt exhaust manifold are worn and allow water from the exhaust to get sucked back into the pump. I first replaced the pump and within a week of dry weather driving the light came back on. I checked the pump and it was again full of water. I just replaced the valves which had deteriorated on the inside. So hopefully this will eliminate the problem. Note - The valves are impossible to remove without removing the 1/2 tubes (held on with 2 nuts) they are attached to the manifold with. The valve threads seize to the tube thread and had to be clamped in a vise to remove - I actually had to hacksaw the valve section to get it off the pipe. Careful as not to damage the threads.
Good luck and try autopartsdirect2you for a new pump and it has life time warranty.
TSB #04-06-04-015 - (Mar 22, 2004)
Some owners may comment on the check engine light being illuminated. Upon investigation, the technician may find a DTC P0410 indicating that there is a concern in the secondary air injection system.
Water may have collected in the AIR pump or the vent solenoid and frozen or corroded the pump.
Replace the AIR pump and install a new inlet hose and solenoid tube assembly using the following procedure:
Raise vehicle on hoist.
Remove shield covering AIR pump.
Remove hose and vacuum lines from pump and solenoid.
Remove AIR pump inlet hose. Do not re-use.
Disconnect electrical connectors from pump and solenoid.
Remove pump mounting bolts and pump.
Transfer isolators from the old pump to the new pump.
Install new AIR pump and bolts to vehicle.
Tighten the bolts to 17N·m (12.5 lb ft)
Route new hose assembly up between engine and fender. It should come up near the area between the battery and the coolant bottle.
Connect new inlet hose to pump inlet.
Connect old outlet hose to pump outlet.
Connect electrical connector to pump.
Connect electrical connector for solenoid to connector on the new hose assembly.
Connect the hose with the white nipple to the vacuum source hose.
Connect the remaining hose to the shut off valve.
Install shield covering AIR pump.
Remove coolant reservoir nut nearest the battery.
Route new hose assembly between the battery and the coolant reservoir with the solenoid on top.
Install the solenoid bracket onto the coolant reservoir stud and reinstall the nut back into the vehicle.
Use a wire tie to keep the new hose assembly away from the engine. On four cylinder engines, tie to the AIR outlet hose. On six cylinder engines, tie to an available hole in the radiator fan shroud.
12590627 Hose Assembly - Secondary Air Injection
12568324 Pump, Secondary Air Injection for 2001 L35 + 2000-2003 L43/LN2
12560095 Pump, Secondary Air Injection for 1999-2000 L35
Hope that helps
Posted on Mar 06, 2010
WHEN YOUR CAR IS COLD LISTEN FOR ANY EXHAUST LEAKS. SOMETIME WHEN ENGINE WORK HAS BEEN DONE AND PARTS HAVE BEEN REMOVED U GET THESE SMALL LEAKS AND THIS CODE SETS. ITS VERY COMMON ON GM VEHICLES
Posted on Jul 27, 2010
Tips for a great answer:
Sep 13, 2016 | 2005 Chevrolet TrailBlazer LS
Sep 13, 2016 | 2005 Chevrolet Chevrolet TrailBlazer EXT...
Sep 08, 2015 | 2001 Cadillac DeVille
Jan 23, 2014 | 2001 Chevrolet Tahoe
Apr 21, 2013 | 1999 Chevrolet Tahoe
Oct 15, 2012 | 2001 Cadillac Catera
Jun 09, 2012 | 2001 Chevrolet Blazer
May 12, 2010 | 2001 Saturn S-Series
Jul 07, 2009 | 2001 Chevrolet Tahoe
165 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: