Question about Cars & Trucks

Open Question

Where is neutral safety switch located on 2008 jeep compass

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: 2004 Jeep Grand Chrokee Neutral Safety Switch Location

The switch is on the transmission..It is usually a dealer item but you can get one from Rockauto.com for about 1/4 of what the dealers charge.

Posted on May 25, 2009

emissionwiz
  • 75005 Answers

SOURCE: Neutral Safety Switch Location

on the transmission where the shift cable attaches.

Posted on Jun 15, 2009

ZJLimited
  • 17970 Answers

SOURCE: Looking for the neutral safety switch

Neutral Safety/Back-up Light Switch

This is a combination switch which controls both Neutral Safety and Back-up lamp circuits.

C6 Transmission


8290dff.jpg

C6 neutral start switch

  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle on jackstands.
  3. Remove the downshift linkage rod return spring at the low-reverse servo cover.
  4. Coat the outer lever attaching nut with penetrating oil. Remove the nut and lever.
  5. Remove the 2 switch attaching bolts, disconnect the wiring at the connectors and remove the switch.
  6. Installation is the reverse of removal. Adjust the switch and tighten the bolts to 55-75 inch lbs. (6.2-8.5 Nm).
  7. Remove the jackstands and lower the vehicle.
  8. Connect the negative battery cable.
AOD Transmission

e7f4231.jpg

Removing the AOD neutral start switch
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle on jackstands.
  3. Disconnect the wiring from the switch.
  4. Using a deep socket, unscrew the switch.
  5. Installation is the reverse of removal. Tighten the switch to 10 ft. lbs. (14 Nm).
  6. Remove the jackstands and lower the vehicle.
  7. Connect the negative battery cable.
4R70W Transmission

2f68dfc.jpg


Removing the Manual Lever Position (MLP) sensor

As of 1994, the neutral safety switch is referred to as a Manual Lever Position Sensor (MLP).
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle on jackstands.
  3. Disengage the harness connector from the MLP sensor.
  4. Remove the 2 sensor attaching bolts and remove the sensor.
To install:
  1. Install the MLP sensor and install retaining bolts. Do not tighten, the sensor requires adjustment.
  2. Adjust the MLP sensor then tighten attaching screws to 80-100 inch lbs. (9-11 Nm).
  3. Remove the jackstands and lower the vehicle.
  4. Connect the negative battery cable.


ADJUSTMENT

C6 Transmission
  1. Hold the steering column transmission selector lever against the Neutral stop.
  2. Move the sliding block assembly on the neutral switch to the Neutral position and insert a 0.091 in. (2.3mm) gauge pin in the alignment hole on the terminal side of the switch.
  3. Move the switch assembly housing so that the sliding block contacts the actuating pin lever. Secure the switch to the outer tube of the steering column and remove the gauge pin.
  4. Check the operation of the switch. The engine should only start in Neutral and Park .

4R70W Transmission


4cc4151.jpg


Adjusting the MLP sensor

Park is the last detent when the manual control lever is full forward. Return 2 detents toward the output shaft for Neutral.
  1. Position the manual control lever in Neutral .
  2. Insert Gear Position Sensor Adjuster tool T93P-700 10-A or equivalent, into the slots.
  3. Align all 3 slots on the MLP sensor with 3 tabs on the tool.
  4. Tighten the attaching screws to 80-100 inch lbs. (9-11 Nm).

I hope help you. Good luck (rated this help).

Posted on Sep 18, 2009

Molson02536
  • 3854 Answers

SOURCE: location of cabin air filter

It can have a cabin air filter, but most vehicles ship without it. Either way, you can access the cabin air filter housing by opening the glove box all the way (squeeze the sides so it clears the stops).

The filters are around $15 at the dealer.

Whether or not there's a cabin filter installed, make sure you're also following Chrysler's recommendations in the owner's manual—running the air on recirculate all the time will encourage mold and bacteria to grow.

Good luck


Posted on Nov 23, 2009

dncholas
  • 222 Answers

SOURCE: neutral safety switch '97 eclipse

Under dash driver side look behind the upper arm of clutch pedal and you should see a green and black wire coming from the button (switch) assembly on the firewall. The wires go up above the clutch pedal. About in the middle of under dash on the left side you should see a white connector these wires run to. Disconnect. I just had the problem and not only starts now but not stalling like it was but it's only been one day but tested it pretty good.

Posted on Aug 16, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location of neutral safety switch


a/t (automatic)
is the PRNDL switch on the side of the trans. the N part, does that.

Sep 15, 2014 | 2004 Jeep Grand Cherokee

1 Answer

Will a faulty neutral safety switch cause a car not to turn over?


Yes, the neutral safety switch prevents the engine to be started except in park or Neutral. When the switch is faulty, it will not start anymore in any position.

Aug 13, 2014 | 2010 Jeep Compass

1 Answer

Where is tcm on 2008 jeep compass located


old post.
there are 4 transmissions.
so...

Jul 04, 2014 | 2008 Jeep Compass

1 Answer

Stuck in park in 2008 jeep compass


does the horn sound when you press the horn switch. if it does not sound replace horn fuse, Or else check brake light switch

Mar 11, 2014 | 2008 Jeep Compass

1 Answer

2008 BMW 528 neutral safety switch location


on steering column if column shift or floor shift might be there

Jan 11, 2014 | 2008 BMW 528i

1 Answer

Neutral safety switch


I would recommend going to the autozone.com website and registering the vehicle. It doesn't cost anything and will give you access to an online repair manual for the vehicle. The steps for replacing the neutral safety switch can be found there. (I checked). Hope this helped and best wishes.

Aug 27, 2009 | 1995 Jeep Cherokee

2 Answers

Where is Neutral safty sensor switch located on Grand Cherokee


OK then the switch is part of the gear selector switch on the side of the trans where the shift linkage hooks up. here is a picture and part number.
ACDELCO Part # C2241 $233.89

673ffc9.jpg

Feb 17, 2009 | 1996 Jeep Cherokee Country

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

246 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...