Question about 2006 Chevrolet Aveo

Open Question

Check engine light on constant code of p0315 (crankshaft position sensor)

Cleaned oil off sensor but light blinked and came on constant again.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 373 Answers

SOURCE: 97 Astro crankshaft position sensor

HI..
Tha crank position sensor On your astro is located.
On front of the engine on timing cover, left side.
Behind the crankshaft pulley. with a connector of 3 wires.

I hope this work for you.

Posted on Jul 12, 2008

  • 10 Answers

SOURCE: PO336 code

Cam Sensor

Posted on Jul 19, 2008

  • 366 Answers

SOURCE: 97 Chevy Astro van lugs, like it misses, B4 finally cranking on

crank shaft sen. is easy enough to change.its mounted near timing chain cover,cam sen.is somewhat harder,its in the distributor,id doubt that both are defect

Posted on Mar 10, 2009

  • 335 Answers

SOURCE: trouble code P0105 continues to set on 2003 chevy trailblazer

If you have bearing problems MAP sensor codes are the least of your worries. Check on the cost of getting a new engine. I hope this is not the problem. Good luck Moe

Posted on Apr 24, 2009

ZJLimited
  • 17970 Answers

SOURCE: crankshaft position sensor location

1990 Chevrolet Cavalier 2.2L TBI 4cyl
The Crankshaft Position Sensor is located under hood, center, rear engine area, below ingnition coil pack and DIS module, mounted in engine block.

87c675c.jpg

Fig. 1: View of the CKP sensor-to-crankshaft reluctor relationship

Crankshaft Position (CKP) Sensor
A magnetic crankshaft sensor (Hall Effect switch) is used which is remotely mounted on the opposite side of the engine from the DIS/IC module. The sensor protrudes in to the engine block, within about 0.050 in. (1.27mm) of the crankshaft reluctor.

I really hope help you wuth this (rated this help). have a nice day, good luck.

Posted on Sep 25, 2009

Testimonial: "Awesome. Thanks."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why won't the car start with the new Crank shaft position sensor installed? 2005 Buick Lacrosse cxl 3.8l engine.


After replacing crank sensor Perform the crankshaft position system variation learn procedure. Refer to Crankshaft Position System Variation Learn !
No you don't need to replace the balancer !
Install a scan tool.
Monitor the powertrain control module (PCM) for DTCs with a scan tool. If other DTCs are set, except DTC P0315, refer to Diagnostic Trouble Code (DTC) List - Vehicle in Vehicle DTC Information for the applicable DTC.
Select the crankshaft position variation learn procedure with a scan tool.
The scan tool instructs you to perform the following:
4.1. Accelerate to wide open throttle (WOT).
4.2. Release the throttle when fuel cut-off occurs.
4.3. Observe the fuel cut-off specifications for the applicable engine.
4.4. The engine should not accelerate beyond the calibrated RPM value.
4.5. Release the throttle immediately if the value is exceeded.
4.6. Block the drive wheels.
4.7. Set the parking brake.
4.8. DO NOT apply the brake pedal.
4.9. Cycle the ignition from OFF to ON.
4.10. Apply and hold the brake pedal.
4.11. Start and idle the engine.
4.12. Turn the A/C OFF.
4.13. The vehicle must remain in Park or Neutral.
4.14. The scan tool monitors certain component signals to determine if all the conditions are met to continue with the procedure. The scan tool only displays the condition that inhibits the procedure. The scan tool monitors the following components:
• Crankshaft position (CKP) sensors activity--If there is a CKP sensor condition, refer to the applicable DTC.
• Camshaft position (CMP) signal activity--If there is a CMP signal condition, refer to the applicable DTC.
• Engine coolant temperature (ECT)--If the engine coolant temperature is not warm enough, idle the engine until the engine coolant temperature reaches the correct temperature.
Enable the crankshaft position system variation learn procedure with the scan tool and perform the following:
Important: While the learn procedure is in progress, release the throttle immediately when the engine starts to decelerate. The engine control is returned to the operator and the engine responds to throttle position after the learn procedure is complete.
5.1. Accelerate to WOT.
5.2. Release when fuel cut-off occurs.
5.3. Test in progress.
The scan tool displays Learn Status: Learned this ignition. If the scan tool indicates that DTC P0315 ran and passed, the CKP variation learn procedure is complete. If the scan tool indicates DTC P0315 failed or did not run, refer to DTC P0315. If any other DTCs set, refer to Diagnostic Trouble Code (DTC) List - Vehicle in Vehicle DTC Information for the applicable DTC.
Turn OFF the ignition for 30 seconds after the learn procedure is completed successfully.
The CKP system variation learn procedure is also required when the following service procedures have been performed, regardless of whether DTC P0315 is set.
• Engine replacement

Feb 07, 2017 | 2005 Buick LaCrosse

2 Answers

P0315 hammer h3 2006


code p 0315 refers to crankshaft position system---variation not learned ===causes engine mechanical fault ---wiring
check for correct air gap from the sensor to the rotor and check for wiring and connections

Dec 26, 2016 | Cars & Trucks

1 Answer

P0315


What repairs were done on the vehicle lately? This is a crankshaft positioned sensor code. If no one went near the sensor, the wiring, trigger wheel, connector, or sensor could be bad. Easiest fix: change the sensor. Right fix: check out the items I mentioned above before spending any money.

Mar 25, 2014 | 2007 Chevrolet Cobalt Coupe

1 Answer

2005 Dodge Neon SXT 2.0L crankshaft position sensor location to replace


P0315 - Crankshaft Position System Variation Not Learned
P0335 - Magnetic Crankshaft Position Sensor Electrical Error China OBD2 car diagnostic tools wholesale on CareUCar

Mar 20, 2014 | 2005 Dodge Neon SXT

1 Answer

What does trouble code P0315 on a 2006 Pontiac Grand Prix mean?


P0315 is a code that indicates and error from the crankshaft position sensor. Typically it is the sensor itself and not an issue with the crankshaft. The sensor itself runs from $30 to $40, but replacement may not be a DIY job unless you're comfortable under a car and removing pulleys from the front of the engine.

Mar 17, 2014 | Pontiac Grand Prix Cars & Trucks

1 Answer

2006 chevy aveo check engine light (code # p0315)


I took it in to a different mechanic and am told that the car will not "learn" the cps. It will clear the CEL but as soon as the key is put in the ignition it comes back on He suggested putting in the original crank sensor but that one is cracked so do I need to get an ac/delco or gm sensor instead of what I got from autozone or how do I get it to recognize the sensor we put in?

We did check the fuses and that is not the problem.

Jan 06, 2013 | 2006 Chevrolet Aveo

1 Answer

Error Code P0315 on 2007 Chevy Aveo


P0315 - Crankshaft Position System Variation Not Learned

Possible causes- Crankshaft Position (CKP) sensor harness is open or shorted
- Crankshaft Position (CKP) sensor circuit poor electrical connection
- Faulty Crankshaft Position (CKP)
- Damaged crankshaft pulse wheel teeth. Tech notes Visual inspection of the Crankshaft Position (CKP) sensor and crankshaft pulse wheel teeth for damage. If crankshaft teethes are OK, replaced the Crankshaft Position sensor

Sep 11, 2012 | Chevrolet Cars & Trucks

1 Answer

Crankshaft position error


Hi there:


CKP SYSTEM VARIATION LEARN PROCEDURE
IMPORTANT:


  • The crankshaft position (CKP) system variation learn procedure is required when the following service procedures have been performed, regardless of whether DTC P0315 is set:
  • Engine replacement
  • Engine control module (ECM) replacement
  • Crankshaft damper replacement
  • Crankshaft replacement
  • CKP sensor replacement
  • Any engine repairs which disturb the crankshaft to CKP sensor relationship


  • The scan tool monitors certain component signals to determine if all the conditions are met to continue with the CKP system variation learn procedure. The scan tool only displays the condition that inhibits the procedure. The scan tool monitors the following components:


  • CKP sensor activity-If there is a CKP sensor condition, refer to the applicable DTC that set.
  • Camshaft position (CMP) signal activity-If there is a CMP signal condition, refer to the applicable DTC that set.
  • Engine coolant temperature (ECT)-If the engine coolant temperature is not warm enough, idle the engine until the engine coolant temperature reaches the correct temperature.




Also cHeck THIS LINK




Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

May 22, 2012 | GMC Acadia Cars & Trucks

3 Answers

2007 aveo misfire faults


gm has a problem with this from way back. double check your spark plugs and if they are not ac delcos, change them. ive seen this time and time again swearing, myself, that there is no way that the plugs would cause this issue. it always comes up with random misfire and usually another 1 or 2 codes misfire codes. put in ac delco, no more codes. let me know

Feb 22, 2010 | 2007 Chevrolet Aveo 5 Hatchback

Not finding what you are looking for?
2006 Chevrolet Aveo Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...