Question about 1999 Ford Escort

Open Question

How do i locate turbine speed sensor on a 06 dodge sprinter

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 316 Answers

SOURCE: input/turbine speed sensor circuit

Your speed sensor, is located on top of the transaxle, near the starter. To access it, remove the battery, then remove the battery tray (4 10mm bolts). You will see wires coming from the lower oxygen sensor, and they snap into the bracket that holds the speed sensor in place. The actual speed sensor has a 2 wire clip on it, and is held in place by the bracket and a 10mm bolt.

Posted on Apr 20, 2009

olwork
  • 237 Answers

SOURCE: 4r70w speedo quits and transmission quits shifting

Be sure to check the vss (vehicle speed sensor) at the output shaft as it's a major input for both engine and transmission. This is the first one to suspect.

Posted on Jun 26, 2009

  • 162 Answers

SOURCE: how do I locate the turbine speed sensor on a ford

its on the front of the transmission below the coil it compares the input shaft/turbine speed against the speed of the output sensor it is checking to see how much slip or diffrenece in shaft speeds the only time the two shafts are spinning at the same time is when torque converter is in lockup

get this sensor from ford dealer for a little more than $100 bucks

Part number F32Z7F040A

Posted on Apr 08, 2010

emissionwiz
  • 74945 Answers

SOURCE: code 715 is reading it

If u go to the link below there u will find a diagram of the transmission, the Turbine speed sensor is part #5 in the diagram, it has an electrical connector going to it.

http://www.justanswer.com/view_image.aspx?href=http%3a%2f%2fww2.justanswer.com/uploads/CTFordTech/2008-08-10_215144_2.0_escort_trans.gif

Posted on Oct 31, 2010

johnjohn2
  • 5763 Answers

SOURCE: i have a troble code

this input sensor is located on the left side of the trany,heres a diagram to help you loacte it, good luck and hope this helps.johnjohn2_62.gif

Posted on Feb 09, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is located the crankshaft position sensor for 2005 dodge sprinter 2500


Is this a deisel motor? If so, it will not have a crankshaft sensor

Jul 19, 2015 | Dodge Cars & Trucks

1 Answer

Input turbine speed sensor location


Hi Mario, I may be behind times, but believe the sensors you're referring to are the turbine pressure sensors. There are usually two, mounted onto he turbo inter-cooler. Regards John.

Apr 21, 2014 | 2002 Honda Odyssey

1 Answer

2007 dodge sprinter engine code p2033


The first one sensor 1 is located just ahead of the converter. The second one sensor 2 (the one you are looking for) is located right after the converter.

Sep 26, 2012 | 2007 Dodge Sprinter

1 Answer

Turbine input shaft speed sensor circuit


both input and output speed sensor are located on the left side of the transaxle case. do not interchange input and the output sensor.

Sep 21, 2012 | 1998 Dodge Intrepid

1 Answer

Location for speed sensor


In the valve body. Best to replace the valve body oem . I was having to may LHM's Replaced BINGO no more LHM very easy to replace.

Aug 05, 2012 | 2006 Dodge Sprinter

1 Answer

I have a 06 2500 dodge sprinter and the fan control speed wheel isnt working. Settings 1-4 will not work. I can feel hot or cold air coming out of the vents while I'm driving but cannot adjust it.


I have changed the resistor 2 times for the same problem. Its under the hood behind the fan motor insulation.
Mine burned because of fan motor frozen & stuck in the winter. Solution is to let the engine warm up before turning the fan on.
Cheers, Brian

Jun 30, 2012 | 2006 Dodge Sprinter

2 Answers

Where is the brake light switch location


removing 2006 dodge sprinter brake switch

Oct 22, 2010 | 2006 Dodge Sprinter

1 Answer

Location of speed sensor a for 99 dodge intrepid


The "Vehicle Speed Sensor" signal is generated by the transmisson output speed sensor. That is the one located at the rear of the case. It is externally mounted. That supplies "vehicle speed" info to the other On-Board Computers. The input turbine speed sensor is located just behind the bell housing area of the case. I believe the trans controller is the only module that needs that info. The Crank Position Sensor give engine RPM info and it is located on the bell housing near the engine block. I hope this helps.

Mar 29, 2009 | 1999 Dodge Intrepid

3 Answers

2006 dodge sprinter esp light on and tire spin light


Go to nearest garage and do diagnosis test and fault erase.

Mar 04, 2009 | 2006 Dodge Sprinter

Not finding what you are looking for?
1999 Ford Escort Logo

Related Topics:

174 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5467 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...