Question about Cars & Trucks

Open Question

Fault code p2100 ford explorer 2004 - Cars & Trucks

Posted by Anonymous on


4 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

  • 783 Answers

SOURCE: need keyless entry code for a 04 an 99 ford explorer

On your 99 model the module is located behind the left quarter trim panel,mid-way.You maybe able to see it by removing the speaker cover or the cupholder on top. The module will have a sticker with a 5 digit code.
On the 04 the model is behind the right quarter trim panel toward the front about even with the right rear door stricker.

Posted on May 17, 2009

  • 432 Answers

SOURCE: 2004 ford explorer will start then slowly sputter


Posted on Sep 24, 2009

  • 682 Answers

SOURCE: golf 06 plate , got fault code p2100 and p2102

P2100 - Throttle valve control motor open circuit.
p2102 - Throttle valve control motor signal too small
look at your throttle valve control motor and see if it is either burnt out or the wires are off.

Posted on Aug 11, 2012

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer


P2100 - H bridge error "A fault has been detected on the circuit connecting the electronic throttle body motor and the PCM. Check for any other non-electronic accelerator control related DTCs and rectify them first. Check area "B" (see system overview) and if no failure is found, install a new PCM". Ford Workshop Manuals

Feb 25, 2015 | Ford Fiesta Cars & Trucks

1 Answer

2005 focus 1.6 limp mode problem and P2100 code

Try clearing the code from the computer. If it returns again, the second hand one could be bad also! Some codes are what they call a hard code, that stays in the computer memory, and will think that the problem wasn't repaired (even though the part was replaced). Till the code is cleared from the memory, the vehicle will return to a limp mode untill the problem is resolved!!

Apr 18, 2014 | 2005 Ford Focus 1.6

1 Answer

Throttle petal not working on a 2004 ford explorer 4.0.

The engine and automatic transmission in this vehicles drive train are fully electronically controlled by a computer called the PCM (Power Train Control Module). Whenever a problem like this occurs the computer stores a record of the problem (there are of course some exceptions to this, like the fuel pump, engine coolant temperature sensor and MAF sensor for instance) in the form of a fault code in its memory, to read these fault codes you must have the systems memory scanned with a special tool. Once the fault code(s) are read you then must perform the appropriate diagnostic testing to find and resolve the problem(s) DO NOT REPLACE ANY PARTS UNTIL A TRAINED TECHNICAIN HAS DIAGNOSED THE PROBLEM TO AVOID SPENDING YOUR HARD EARNED MONEY ON PARTS THAT MAY NOT CORRECT THE PROBLEM

Aug 29, 2012 | 2004 Ford Explorer

1 Answer

Golf 06 plate , got fault code p2100 and p2102

P2100 - Throttle valve control motor open circuit.
p2102 - Throttle valve control motor signal too small
look at your throttle valve control motor and see if it is either burnt out or the wires are off.

Aug 11, 2012 | Volkswagen Microbus Cars & Trucks

1 Answer

2004 ford no speed replaced spark plugs already

The 1st thing that needs to be done here is to have the electronic engine control module checked for fault codes, this is called an "OBD2" fault code test. You should alsp have the fuel presure tested as low pressure can cause this.

Feb 22, 2012 | 2004 Ford Explorer

2 Answers

2004 Ford Explorer XLT.....The radio and gas gauge quit

The check engine light will represent fault codes that the computer is sensing. Have a mechanic, or go to your local auto parts superstore and have them scan for the fault codes. This will at least give you an idea about some of your problems.

Apr 15, 2010 | 2004 Ford Explorer

1 Answer

2004 Ford Explorer--65k miles..service engine soon light on...not gas cap, had fuel system chemically cleaned by Precision tune...

get the code to determine what system is at fault. If you already did and it directed you to the gas cap then thats about all you can do other than look at the engine and air box for any vacuum hoses that may of been left off.

Nov 05, 2009 | 2004 Ford Explorer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

79186 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

13735 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides