Question about 2000 Pontiac Montana

1 Answer

Driverside window will not close - 2000 Pontiac Montana

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.


    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 15 Answers

It's one of three things; these are, the window switch, a fuse gone or your window motor is burnt out. Hope this helps

Posted on Jan 05, 2013


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Why I got no power window

one window? or all? if one window it maybe locked on driverside there sometimes are lock buttons which the driver can control to allow to open or lock closed or in position if all? I suggest looking at your fuse box and look for one that says windows/ if after pulling and wire inside burnt in half replace with same type of fuse. If none of these and just one window ? you may have a burnt out motor for that window which of course would need to be replaced

Jul 17, 2014 | 2003 Jeep Liberty

1 Answer

Driverside window jam

Can you hear your power window motor trying to move the window?

Jan 05, 2013 | 2000 Pontiac Montana

1 Answer

Power windows not working

check for blown fuses?you've most likely done that. open hood and look on the driverside fenderwell for a black main fuse and relay center or box, open the box and look under the lid for locations of relays and fuseslocation the fuse for electric widow and as you look at the fuse,you will see a horseshoe type metal ring inside the plastic 'window' if it's broken(the hORSESHOE} the fuse is bad and needs a new one.there is also a fuse panel located on the driverside of dash,open the door and you should see a removeable plastic cover on the drivers door at dash panel just to the left where the door closes. remove that cover to expose the fuse panel to inspect for blown fuses. thank you for choosing

Apr 08, 2011 | 1994 Buick Century

1 Answer

Driverside window won't comes back up to close

Have to remove the door panel and look over the window mechanism to determine the problem, Only then, can you adjust or replace the effected parts.

Apr 28, 2010 | 1999 Lincoln Navigator

2 Answers

First the driverside window would not go down . then it went down, and wont go up.

a plastic safety gear that protects against closing injuries is broke inside the window motor-thats common -someone may hav stuck something inside window and caused it to break

Apr 26, 2010 | 2000 Chevrolet Blazer

1 Answer

Driverside electric window will not close

there are two metal terminals inside which actuate the window mech, now what happens is because the terminals constantly spark (ever so slightly) everytime you hit the switch it blackens the terminals and as the driverside is most used its always the first to go, a good way to test this is to wiggle the switch when pressing down on it and this should help make a connection, to fix permanently, ever so gently take out the power window switch and disassemble it there will be two lugs that come off the window switch you are wishing to fix, they are in the center of the switch at the pivot point, they are the only things that hold the switch top on, be carefull not to break thoes lugs or the housing they are in and gently pry the switch out, be carefull as there are 2-4 small springs and two brass terminals that you cannot loose or your screwed, clean the two long brass terminals with a fine sand paper and clean out all greassy stuff they put in there, now a very light amount of vasalene only on the parts that appear to need lube (springs etc) and put the switch back to gether VOILA should work like new. hope this has helped. matt

May 15, 2009 | 2002 Dodge Grand Caravan

1 Answer

Non Working driverside power window 86 GMC

sounds like you need a window regulator to me check napa or a good parts store

Mar 19, 2009 | 1986 GMC G3500

Not finding what you are looking for?
2000 Pontiac Montana Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts


Level 3 Expert

80339 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides