Question about Chevrolet Chevy

Open Question

Chevy blazer starter stays engaged - Chevy Chevrolet Cars & Trucks

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

bryant329
  • 125 Answers

SOURCE: 1999 Chevy Blazer Starter

the starter is located on the passenger side lower motor. it has two bolts in it that hold it in place. it actually goes through a hole/slot in the transmission to the flex plate.

1st. disconnect the negative cable on the battery.
2nd. raise the vehicle safely and place a jack stand under the vehicle out of your way but near where you will be working(for safety).
3rd. remove the two bolts that hold the starter in place.
4th. remove the wires from the back of the starter.
5th. install in reverse order of above.

note: there may be little plates between the starter and the mounting points called shims. if there are then make sure you put them back.

Posted on Sep 24, 2008

  • 41 Answers

SOURCE: how do you remove the starter from a 1996 chevy 4WD blazer?

NO, it's kind of tight, but it's not that bad. You do need to remove the torque converter cover, and slide/rotate it as much to the driver's side of the vehicle as possible.

Posted on Jan 23, 2009

roniecon
  • 6826 Answers

SOURCE: my 2000 chevy blazer engageing it 4x4 lo range by it self.

Control switch is bad.

Posted on Mar 10, 2010

  • 1 Answer

SOURCE: Parking brake won't stay down although it engages

Thiers a little pin insige the pedal. Its proubly broke inside. you go to the dealer or junk yard to get another one.

Posted on Mar 31, 2010

Testimonial: "thanks!"

  • 128 Answers

SOURCE: 98 chevy cavalier starter stays engaged WITHOUT

Starter pinion sticking. Remove starter and inspect. May need new starter

Posted on Nov 30, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Starter stays engaged on my 06 Chevy Malibu


There are a few possibilities...
  1. Starter improperly shimmed and is biding to flywheel.
  2. Starter or flywheel teeth worn causing binding (not likely)
  3. Starter solenoid return spring broken.
  4. Ignition switch problem causing starter to stay powered after key released.

Aug 02, 2014 | 2006 Chevrolet Malibu

1 Answer

Starter draging


Either you have a voltage drop to the starter, OR the starter needs to be shimmed as it might be to tight against the Ring Gear when engaging.

Dec 23, 2013 | 1991 Chevrolet S-10 Blazer

1 Answer

All acc power stays on and starter wont stop turning over when battery is connected in my 1997 chevy blazer


I would take a look at the wires down at the starter. He may have the large positive wire shorting to the smaller, trigger, wire. This could potentially cause a back-feed through the whole system.

Jan 28, 2013 | Chevrolet Blazer Cars & Trucks

1 Answer

1999 chevy blazer wiring harness diagram for remote start


Large purple wire is your starter engagement wire, I believe you will have to tie into more than that wire to get your remote start to work properly, maybe get me brand and model number so I may research more and point you in the right direction as far as installation goes.

Nov 30, 2011 | 1999 Chevrolet Blazer

1 Answer

Problem with a 2000 chevy blazer not starting


Have replaced starter, alternator , ignition wiring, neutral safety starter switch, still happens ??????? Do you know how to do automotive electrical testing ? Not guessing an replacing parts . Not starting ??? How ? when you turn the key to start does the starter motor engage an spin the engine ? Or when you turn the key to start nothing happens ? A no crank no start or a cranks no start . Plus you shoud learn how the system works before trying to diagnose .

Jun 18, 2017 | 2000 Chevrolet Blazer

1 Answer

Parking brake won't stay down although it engages when I hold it down on 2003 Chevy Blazer.


Thiers a little pin insige the pedal. Its proubly broke inside. you go to the dealer or junk yard to get another one.

Mar 31, 2010 | 2003 Chevrolet Blazer

1 Answer

My 2000 blazer 4.3 4x4 starter contiues+strange rattle


solinoid stays engaged. needs replace. the rattle could be a cat convertor bad.

Jun 12, 2009 | 2000 Chevrolet Blazer

2 Answers

Wiring diagram for 92 chevy blazer


My 1992 Chevy blazer s-10 starts and then the door locks automatically starts locking and unlocking...It wont stay running either...

Jun 11, 2009 | 1992 Chevrolet S-10 Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...