Question about 1999 Lexus ES 300

2 Answers

The pos cable came off while driving the car stop put it back on and the eng. light tra light came on what do i do

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 325 Answers

You could try putting the ignition in the`ON`position(dash lights only) remove negitive battery terminal for 90secs with ignition still on re-connect the battery.If that fails find someone with a code reader to put the light out..Hope it helps...

Posted on Jan 05, 2013

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 3 Answers

Try disconnecting the negative cable (with key in off position) for at least 30 seconds, or you could remove the "EFI" fuse located in the engine compartment fuse box for about 30 seconds also. If that fails, then you need to have it scanned for codes (DTC's) and go from there.

Posted on Feb 04, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 77 Chevy c30 has no power. Jumped started it and drove it home. I turned it off then tried to restart it. No power no lights. nothing. Battery is good. An u help will be appreciated.


If the battery is good you will need to follow flow. Test light is the easiest to use. First hook light to ground and touch pos terminal,lights good next touch pos battery cable end, lights good. Next follow pos cable to starter pos terminal,lights good. Next hook test light to bat pos teminal,touch neg terminal,lights good. Then touch engine block, lights good ground. Next move test light clamp back to ground/neg side and touch alt pos terminal,lights good.if all that tests good, if all good move inside and check for power at ign switch pos term if at any time you dont find power you have wiring issue that needs to be addressed. Let me know what you find. Russ

Mar 29, 2015 | Chevrolet Cars & Trucks

1 Answer

How to reset the check engine light on a 1998 blazer


Remove pos battery cable for 15mins reset the computer put back. On tighten pos cable

Jun 02, 2014 | 1994 Toyota Celica

2 Answers

Took battery out of my 1993 buick riviera,put back in now starts then dies


how did you disconnect the battery, pos first then neg ? or neg first then pos ? try starting it and after started, hold your rpm at 1500, for about two minutes, then if still running, drive it to get to.speeds of 40 for about 15 minutes, this is to relearn if not, disconnect your battery, take the pos and neg cable and touch them together and hold for about a minute, then Connect them back, neg.first.then pos, then follow steps above to.relearn.

Dec 09, 2013 | 1993 Buick Riviera

2 Answers

How to reset engine light


pull off pos bat cable for approx. 1 minute then reinstall

Nov 08, 2013 | Dodge Challenger Cars & Trucks

1 Answer

Wont start


unhook battery pos and neg touch both cables together to decharge computers and clear eng lights touch together for 1 min. Then hook cables back to battery try to start hope that helps

MAKE SURE BOTH CABLES ARE OFF BATTERY

if that does not work it could be a ignition switch or cyinder make sure you get it scanned for codes to deterime that.

Jan 30, 2013 | 1998 GMC Sonoma

1 Answer

2007 escalade instrument panel stopped working


Take the cables off the battery. Touch the two cables together (away from battery) and them together for 15 seconds. PUT POS CABLE BACK ON FIRST. Then neg cable. If this does work, cluster will need to be replaced.

Nov 29, 2012 | 2003 Chevrolet Tahoe

1 Answer

Driving home today in our 2004 Jetta. first the ABS lights came on, then the air bag warning, then the brake light, then the battery light, and an EPC light, all within minutes, then the power steering...


WILL THE ENGINE START? IT SOUNDS LIKE THE BATTERY IS LOW OR THE BATTERY CABLES & TERMINALS NEED TO BE CLEANED. TAKE THE NEG. CABLE OFF FIRST THEN THE POSITIVE, CLEAN EVERYTHING TERMINALS & CABLES, PUT CABLES BACK ON BATTERY POS. FIRST, TIGHTEN IT. THEN DO THE NEGATIVE & TIGHTEN IT.

Dec 25, 2010 | 2004 Volkswagen Jetta

1 Answer

Car shakes after stat up


check the battery ,check and replace wheel bearings,check replace wires and fuses.

Jul 19, 2009 | 2006 Jeep Commander

1 Answer

Coolant light stays on and drives hard.


take the postive cable off the battery and wait 30 sec and connect it back up again it resets the computer

Jul 09, 2009 | 1999 Chevrolet Monte Carlo

Not finding what you are looking for?
1999 Lexus ES 300 Logo

98 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexus Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

881 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...