Question about Cars & Trucks

1 Answer

Replace oil pan chevy k10 - Cars & Trucks

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Cars & Trucks Expert
  • 325 Answers

Bit fiddly but can be done with engine in place.Drop exhaust at manifold joint,unbolt engine mounts lift engine unbolt sump.you may have to drop off oil pick up pipe to get sump out.Hope this is helpful...

Posted on Jan 05, 2013

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 191 Answers

SOURCE: Doors for my 1984 chevy k10

1973 to 1987 the differences will be the windows and trim some of them had wing windows and some did not.

Posted on Jan 09, 2010

moparownr
  • 667 Answers

SOURCE: when replacing the oil pan gasket for a chevy k10

Oilpan bolts should not be tightened more than 14 ft pounds. Hope this helps, let me know

Posted on Mar 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace a oil pan on a 1993 chevy c1500 2 wheel with a 5.7 liter engine?


Drain the oil. Loosen the engine mounts and jack up the engine. Put 2x4s under the mounts. Remove all the pan bolts and drop the oil pan. You will also need to disconnect the oil cooler lines at the oil filter housing to get to some of the pan bolts. There are also some engine support brackets you will need to remove.

Oct 21, 2014 | Cars & Trucks

1 Answer

Chevy k10 turn signal


Without a diagram I have no idea

Mar 22, 2014 | 1985 Chevrolet Chevy

1 Answer

Where is oil pump located on 1999 chevy blazer


The pump is inside the oil pan. Have to drop the oil pan to get at it.
Will need to replace oil pan gasket also, can not reuse old one.

Sep 07, 2011 | Chevrolet Blazer Cars & Trucks

2 Answers

I have no oil pressure on the gauge on the dash board and it is leaking oil under neath the engine what could it be. 97 chevy silverado 2500 4by4


Could be a broken oil pressure sending line or something worse.... Hole in oil pan, broken/missing (blown-off) oil filter.

Sep 27, 2010 | Chevrolet Silverado 2500 Cars & Trucks

1 Answer

What is involved with replacing the oil pan on 1998 GMC Sierra?


  • Step 1 Raise the truck using the proper equipment. Use a ramp or a jack and jack stands to support the vehicle securely by following all directions for use provided by this equipment's manufacturer.
  • Step 2 Drain all oil from the Silverado by placing an oil drip pan under the vehicle's engine block, directly under the oil drain plug. The drain plug is located on the oil pan, between the vehicle's tires underneath the vehicle. Use a wrench to loosen and remove the plug allowing the oil to drain into the pain below.
  • Step 3 Notice the various items attached to the oil pan or in the way of the oil pan dropping. For the oil pan to drop, remove the negative battery cable, front differential (only for four-wheel drive vehicles) and the under body shield by using a wrench or socket set.
  • Step 4 Remove the oil pan shield by loosening the four bolts holding it in place along the edges of the shield. Then, remove the cross brace, oil filter, the transmission to oil pan bolts and the oil level sensor.
  • Step 5 Follow the removal of those pieces by removing the bolts from the two front wiring harness, the engine wiring harness retainer, engine oil cooler pipe to oil bolts and the transmission oil cooler pipe retainer using a wrench. Located the closeout covers and bolts located on each side of the engine and remove them.
  • Step 6 Disconnect each of the oil pan bolts using a wrench that will allow the oil pan to drop. The oil pan gasket will also fall off and replacement should occur before reinstalling the oil pan.


  • Read more: How to Drop the Oil Pan in a Chevy Silverado | eHow.com http://www.ehow.com/how_4508109_drop-oil-pan-chevy-silverado.html#ixzz0wi82Ul2u

    Aug 15, 2010 | GMC Sierra 1500 Cars & Trucks

    1 Answer

    When replacing the oil pan gasket for a chevy k10 what should the torque setting be?


    Oilpan bolts should not be tightened more than 14 ft pounds. Hope this helps, let me know

    Mar 04, 2010 | 1985 Chevrolet Chevy

    1 Answer

    Doors for my 1984 chevy k10


    1973 to 1987 the differences will be the windows and trim some of them had wing windows and some did not.

    Jan 09, 2010 | 1984 Chevrolet C1500

    1 Answer

    '86 chevy k10; e.brake pedal is stuck


    hold hte release had have somone pull the cable back form underneath the vehicle, with any luck only the front cable is stuck, if not use lots of penetrating oil to try to free the rear cables,

    Nov 14, 2009 | 1986 Chevrolet K1500

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    68 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Cars & Trucks Experts

    yadayada
    yadayada

    Level 3 Expert

    75822 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Randy Ohler

    Level 3 Expert

    14585 Answers

    Are you a Car and Truck Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...