Question about 2001 Mitsubishi Mirage

1 Answer

Need to know how to replace my bulb for my mitsubetshi mirage car

Dont know how to get the rubber that surrounds the old bulb

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert that has over 500 points.

  • Expert
  • 325 Answers

These covers are water tight,slide a small flat bladed screwdriver between bulb and cover ease all the way around it should slide off.When refitting put a smere of oil on the rubber and slide on.Don`t touch the bulb glass it will just blow!Good-luck....

Posted on Jan 05, 2013


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

1999 Isuzu rodeo 2.2l location of the check engine light bulb and how do I replace the old bulb?

the CEL lamp on all cars,(if a real tungston bulb) is in the cluster
use a flash light and aim there, see it> YOU WILL.
now you know where it is, if cant see it now wait until dark and use the flashlight.
2nd question, im sure there are more, but 2nd, is removing the cluster. (to replace old bulb twists is base socket CCW, its out.
this car has electronic speedo so no troublesome cable to trans
simply unscrew the cluster and pull it.
see those screws there? some cars need the ignition key surround shells removed first. I look first.....

Nov 12, 2015 | Isuzu Cars & Trucks

1 Answer

2001 Ford Escape - No low beams. Replaced bulbs, replaced relay. How do I determine if its the switch or module?

You need to view if the terminals are corroded. If the rubber surrounding the light to seal it is warped, this will allow moisture to enter and corrode the contacts.

Mar 28, 2011 | 2001 Ford Escape

1 Answer

Having problems with the trunk latch. is this a standard problem with the mirage?

i dont know how common , but i had a few with latch problems,both neede replacing, theres a spring that let go and wouldnt latch after shutting the trunk,and also had one that latched before the trunk was closed and all that need was to turn the key in the lock and pop latch back open,

May 28, 2010 | 2001 Mitsubishi Mirage

1 Answer


engine rubber holdings are old
should be replaced dont rush

Mar 09, 2010 | 2001 Mitsubishi Mirage

1 Answer

Detailed explaination on changing headlights on a 1999 mistsubish

Your headlights are just bulbs that need to be changed from under the hood. When you open the hood and look at the back side of the headlight you will see the wires sticking out.There is a black plastic ring that you will need to twist counter clockwise about 1/4 of a turn then pull. You will end up with this ring the socket and the old bulb in your hand at this point. If you look at your new bulb (don't handle by the glass!) and compare it to the old you will be able to see how the socket comes off by pulling. Reinstall in oppisite order and you will be fine.

Aug 26, 2009 | 1999 Mitsubishi Mirage

1 Answer

1998 mitsubishi mirage and it has been parked for about 3 months outside in rain/snow/freezing temps. now the rear wheels are seized up and will not turn. engine runs and Fron wheels work fine, rear wheels...

no get a rubber mallet and un bolt the bolts and give the wheel (not the tyre) a whack with the rubber mallet and the wheel should come off then bolt it all back up and try it then

p.s. dont use a metal or wooden mallot or hammer as the wheel will shatter

Feb 28, 2009 | 1998 Mitsubishi Mirage

2 Answers

How do I replace the headlight bulbs in my 2002 Mazda 626

if the lens covers are yellow or discolored you would have to remove the lens and they have chemical at autozone or napa that can take care of this problem but to replace the bulb you open the hood and put your hand in behind the headlight assembly and there is a plug you normally turn counter clockwise and the bulb comes out always wipe the bulb off if you touch it with your hand because the sweat from your hand will cut the life of the bulbs

Jan 18, 2009 | 2002 Mazda 626

1 Answer

Headlight replacement

Open the hood, Turn the twist lock sleeve the surrounds the wiring harness end and pull out bulb holder. Pull out old bulb, press new bulb tab into slot, replace unit back into light housing, turn twist lock sleeve to secure to housing.

Dont touch the new bulb with your bare fingers.

Skin oils can heat up on the bulb and cause it to fail.

Jan 17, 2009 | 2004 Hummer H2

1 Answer

How do I change my headlight bulb

go to your parts suppler and ask for a H4 globe pop your bonnet and remove the plug on the back of your head light then remove the rubber boot paying attention to which way it cam off then you will find a spring clip unclip it but be careful not to damage its anchor point. remove old globe an throw away take new globe out of box DO NOT TOTCH THE GLASS OF THE GLOB AS IT WILL CAUSE THE GLOBE TO BLOW STAAIGHT AWAY AFTER FITTING IT handle the globe by the metle bass and fit it, refit spring clip and rubber boot fit the plugf and check the operation of the light

bingo you are done have a nice day

Dec 21, 2008 | 1999 Mitsubishi Mirage

Not finding what you are looking for?
2001 Mitsubishi Mirage Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts


Level 3 Expert

80417 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides