Question about 1994 Jeep Grand Cherokee

1 Answer

All in one Belt keeps coming off Bottom pulley of motor

And pully dosnt look right when motor is running

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An user who is expert in 3 categories / brands.

  • Jeep Master
  • 1,455 Answers

Sounds like the crank pulley is damaged. You will have to replace it. There's a bolt in the center that has to be removed and then you will have to get a puller tool to "pull" it off the crankshaft.

Posted on Jan 09, 2013


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Escort 2000 twin cam...belt comes off pullies when running belt is tight

use a straight edge and figure out which pulley is tilted and repair.

Sep 25, 2014 | 2000 Ford Escort

1 Answer

Belt keeps falling off bottm pulley on motor not seat belt

remove the lower pulley (crank pulley and balancer assembly)
and inspect it. if any problems replace it.

Jan 05, 2013 | 1994 Jeep Grand Cherokee

1 Answer

Sparks are coming from the bottom pulley?

remove the belt eng not running of cource turn all belt driven pullys by had bet u find ur prob.

Jun 04, 2012 | 1998 Jeep Cherokee

1 Answer

2006 ford tauras i replaced batterie,alternator,and belt i have a noise coming for the bottom pulley while i spray wd40 around the bottom pulley only the noise stops what makes this pulley go out and how...

First, if you have sprayed WD-40 on your belt, your belt has been wrecked and needs to be replaced again. WD-40 will only soak into the belt and CAUSE it to slip and make noise.

Then you need to check the alignment of all the belt pullies. The tensioner pullies on many Fords can wear and sit a little out of alignment and cause the belt to rub sideways against the other pullies. Replacing the belt tensioner usually fixes it.

Jul 09, 2011 | 2006 Ford Taurus

1 Answer

I have a 2000 Oldsmobile Silhouette and the belt that goes around the motor keeps messing up. The inner part of the belt starts coming apart. We have replaced the pulley and are on the 4th belt now. The...

Can be a sign of a mis-aligned pulley. If a pulley is not perfectly flush with other pulleys, or skewed ( cocked a bit) it will tear up your belts. This is usually caused by worn out bolt holes retaining the component or its bracket, or a worn out component causing the pulley to wobble. With the belt off, Visually check pully alignment and skew with a straight edge. Using your hands, try to make eack pulley wobble by pulling back and forth on it to feel for play in the pulley bearing. No play is acceptable for and component pulley other than very slight play in tensioner pully. Ive seen A/C compressor and alternator pulley do that type of belt damage. Mike

Jun 13, 2011 | 2000 Oldsmobile Silhouette

1 Answer

1992 nissan maxima timing belt replacement

need to take off almost every thing from the front of the motor. then take off top half of timing cover.
pull the harmonic balance pully off. then the bottom half of the cover will come off. becareful
the cam gears are hard to aline.
do you no where the knock sencor is located?
if so please email me @

Mar 07, 2009 | 1992 Nissan Maxima

1 Answer

Not currently at home to help son, he just called and his 1997 cutlass supreme six cylinder bottom motor pulley not turning with belt. Making a loud sound due to belt slipping on bottom pulley What does...

That Bottom Pulley is for the Timing Belt and the Crankshaft. There could be a lot more Problems than what he can see. Hopefully the Pulley is just Bent and he will not have to tear into the Motor for repair. Please Rate My Response! Thanks!

Feb 02, 2009 | 1997 Oldsmobile Cutlass Supreme

1 Answer

Altonator belt help for escort 1998 gti zetec

I tried to attach a photo of the diagram but, would not let me. Remember the smooth side or back of the belt runs on the smooth pulleys. The grooved rides on the grooved pulleys. Starting at the altermator it goes around the topof the alternator then below the tensioner then around theback side and bottom of the crank pulley and the bottom of the a/c compressor. There is a small smooth idler pulley just above the a/c that the back side of the belt rides on then it goes to the outside of the p/s pully then back up to the alternator. Hope this helps. I will try to attach the photos again.

Jan 02, 2009 | 1997 Ford Escort

2 Answers

Serpentine belt keeps slipping off when it rains.

I have had the same trouble with my 2002 zx2. I have had to reinstall or replace the serpentine belt 4 or 5 times in less than a year. I have replaced the idler bearing and then the water pump went out which took out the belt as well. The belt still came off after replacing those items when I hit another puddle of water. I found that proper installation of the plastic engine splash guards which bolt to the bottom around the motor play an important roll in keeping out road water. Since the pulleys are accessible with the right front tire removed, I focused on securing the plastics tightly around the wheelwell framework. This has helped extremely in keeping water away from the pulleys. I haven't had any more troubles in the last 7 or 8 months. I'm still leary when driving in the rain as the routing of the serpentine belt on this car is the worst I've ever encountered.
Bottom line, check/replace idler bearing, tensioner if needed and make sure all plastic splash guards are there and properly screwed to the frame and each other.
Hope this helps.

Dec 26, 2008 | 2003 Ford Escort

Not finding what you are looking for?
1994 Jeep Grand Cherokee Logo

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts


Level 3 Expert

80608 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides