Question about Cars & Trucks

Open Question

Is there afuse to check on code po783 1997 dodge ram 1500

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 840 Answers

SOURCE: passanger side mirror replacement on 04 dodge ram 1500?

very easy take the mirror inside cap off if you can not get to the 3 bolts then you will have to take trim panel off to take trim panel off look for plastic caps take them out and unscrew them then pop out the bottom of the door and pop the sides out then lift up and out should be loose enough for the bolts now/ 10mm bolts 3 Please rate my response thank you very much

Posted on Feb 02, 2009

Ad
  • 1 Answer

SOURCE: 1998 dodge ram 1500 v85.2 towing capacity?

according to the owners amnual the max towing weight for a 1999 ram 1500 quad cab wit automatic transmission is 7600 lb.
with either 5.2 or 5.9 v8. for a reg cab it is 8000 lb.

Posted on Jul 23, 2009

outdoorsman5
  • 631 Answers

SOURCE: 1999 Dodge Ram 1500 Pickup error code p0171

This code means that system to lean, bank 1.
some of the possible causes to make this code set are
1. intake or exhaust leak,
2. problem with the air system.
3. MAF (Mass Air Flow sensor)VAF sensor (Volume air flow sensor)
4. fuel pressure/pump
5. injector(s)
6. HO2S (Oxygen sensor)

Posted on Sep 16, 2009

  • 880 Answers

SOURCE: what is this code P1404 on the dodge ram 1500 mean

That code is the EGR. I'd start by checking for a bad connection on the EGR plug-in. Pull the connector off and inspect each individual terminal inside the plug and the connector pins inside the EGR valve.
I found this solution at another forum on this issue. It worked on my 2001 Grand Am:

"Many GM built cars have a tendency to have the 'Check Engine Soon' light come on as a result of DTC code P1404. P1404 is described as EGR valve pintle stuck open, which in most cases is a false alarm. I had this happen with my '01 Grand Am. A little bit surfing on internet reveals that GM has a solution for the problem, a re-flash for the car's computer.

A software re-flash as a fix kind of indicates that the vehicles with this problem were built with it but I don't think GM will be re-flashing cars outside warranty for free. They will want their $100 for it.

Some hands on people I found had purchased a new EGR valve and changed it but the problem remained.

Possible reason (very likely) for the false P1404 code is that the plastic piston of the EGR valve position instrument (LVDT?) wears over time and starts reading a different position at valve closed than what it was when the EGR valve was first installed.

When the car was built and the computer circuits energized for the first time the computer learned the EGR valve closed position signal from the valve position instrument that is built on top of the valve itself. Over time, when the instrument wears, a slightly different signal is sent to the computer and when it differs enough from the 'Valve Closed Signal', that the computer had learned, the trouble code P1404 is set and the 'Service Engine Soon' light comes on.

Replacing the EGR valve with a new one does not necessarily fix this problem because the 'Valve Closed Signal' between valves is slightly different and it is just pure luck if your new valve would give a 'Valve Closed Signal' close enough to your original valve's signal not to set the trouble code. This is why the new EGR valve 'Valve Closed Signal' must be re-learned by the computer.

So, what this all means is that if the P1404 is a false code meaning that the valve pintle is not stuck open, then new 'Valve Closed Signal' can be re-learned by the computer using the old valve.

For fixing this problem the tool you need to have is a simple OBD II code scanner that can be used to erase trouble codes. There are many scanners of different price range on the market. I purchased one from AutoZone for about $90.

A code scanner is a very handy tool to have and I recommend everybody who is just slightly hands on type of a person to get one. It will end up saving a lot of money over time.

The fix goes like this:

1. Disconnect the wire harness from the EGR valve.

2. Turn key ON and erase the trouble code(s) from the car's computer AND TURN KEY OFF IMMEDIATELY WHEN THE SCANNER SAYS CODES HAVE BEEN ERASED. DO NOT TURN KEY ON BEFORE YOU RE-CONNECT EGR WIRE HARNESS.

3. Re-connect EGR wire harness and your problem should be fixed.

I learned this fix from OBDII.COM where carfixer and kozloski discussed it and I think kozloski was the one who provided the solution, so thanks to them.

There was also other people stating that this fix really works. Now I have joined this group of people as I got mine fixed using this trick also.

I believe erasing codes with wire harness disconnected and turning the key OFF right after P1404 code has been erased re-sets the 'Valve Close Position' reading in the computer and triggers computer to re-learn position next time the key is turned ON.

If you don't have an OBD II scanner and don't want to buy one some car part stores may erase the code for free, but if you have it done there you must tell them about turning the key OFF at the right moment. Other wise the re-learn process does not take place.

Posted on Feb 10, 2010

leedavidian
  • 1420 Answers

SOURCE: Ecu wiring diagram dodge ram 1500 5.9

Welcome to Fixya.com Thank you for using FixYa, Regards, Lee Davidian dede7d5.pngTTo zoom in hold control and tap the + or - key, Lee

Posted on Apr 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Key is stuck in ignition receiving no electricity


You are not the only one:

Key stuck in ignition, wont start, dodge ram pickup - Fixya

www.fixya.com/.../t14560159-key_stuck_in_ignition_wont_start_dodge
Oct 6, 2012 - key stuck in ignition, wont start, dodge ram pickup - Dodge Ram 1500question. ... 631 Answers. SOURCE: 1999 Dodge Ram 1500 Pickup error code p0171. This code means ... Jun 28, 2011 ' 1987 Dodge Ram 50 ยท 1 Answer .

Aug 23, 2015 | 2011 Dodge Ram Pickup 1500

1 Answer

Dodge ram 1500 5.7 4x4 Cruise control shut off


have the cel checked need to know what the code is to diognose

Oct 09, 2013 | Dodge Ram 1500 Cars & Trucks

1 Answer

What does the p1391 code on a 99 dodge ram 1500 5.2l v8 meen


check engine light and code P1391 crank or cam position sensor

The above can cause rough idle on the Dodge Ram 1500 5.2L V8 Engine.

Can try to replace the sensor, but verify that the wires are ok first.

Aug 12, 2010 | Dodge Pickup Cars & Trucks

1 Answer

How can I find a fault code on my 2005 dodge ram 1500 using the check engine light?


you cant check codes on that year truck without a code reader. ive seen them as cheap as 30 dollars at kragens and harbor frieght has code puller/scanners for around 100 dollars. all you have to look for on the box is OBDII

Apr 03, 2010 | 2005 Dodge Ram 1500

1 Answer

Check engine light on code p0441 dodge ram 1500 my 2007 dodge ram 1500 is puttering and acting like it wants to die out can you let me know what the problem is.


This trouble code is Evap Purge System Performance fault. 1) Check for a loose or missing fuel cap. 2) Check for a damaged or missing fuel cap seal. Recheck for other trouble codes. This fault wont cause the stumblering problem. It turns on the MIL lamp to say there leak in the EVAP system.

May 10, 2009 | 2007 Dodge Ram Truck

1 Answer

1998 Dodge ram 1500 running sluggish, check service codes


GO BACK TO YOUR LOCAL PARTS STORE TO SEE IF THEY CAN SCAN YOUR TUCK IF YOU GET CODES GO TO TROUBLECODES.NET TO SEE WHAT THEY MEAN

Apr 03, 2009 | 1998 Dodge Ram 1500 4WD

2 Answers

2001 dodge ram 1500 fault code 1687


Heryou go its a pretty lengthy diagnostic procedure it appears there is a power problem with the instrument cluster here is the code meaning hope it helps have a good dayDB0b0195e.gif

Feb 19, 2009 | 2001 Dodge Ram 1500 Truck 2WD

3 Answers

2004 DODGE RAM 2500 DESIEL


the transfer pump is going bad ...dodge has an intank replacement for your vehicle

Nov 11, 2008 | 2004 Dodge Ram 1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

97 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...