Question about Cars & Trucks

Open Question

2007 chevy malibu fuel pump access panel - Cars & Trucks

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

rick_amick
  • 69 Answers

SOURCE: drivers door panel removal

The book says 1. remove power accesory switch panel by using suitable flat blade tool at front. 2. Disconnet electrical connections.
3. pry door handle plug by using small flat bladed tool
4.remove door trim handle mounting screws
5. remove door trim panel from retainers.Start at rear bottom corner and pry outward.
6. remove door panel.
KD does make a tool that will properly pry the door panel away from reainers. KD 3705 You might get by with a screwdriver.
One other thing you may need to have the window down to get the panel to come off. You will have to lift up on it once it is loose from the fastners.
Hope this helps you out.

Posted on Mar 24, 2009

  • 55 Answers

SOURCE: fuel pump 2001 Chevy Tahoe

no there is not. the only way to access is to drop the gas tank down.

Posted on May 25, 2009

  • 3640 Answers

SOURCE: dtc code p0121 and p2135 2007 chevy malibu

both codes refer to the throttle position sensor, the sensor is at the throttle plate, on the side of the throttle body. to test remove the connector to sensor, use a ohms meter to test. put 1 lead to top connection and the other to the bottom one. move throttle and the needles on the ohms meter should move very even, move throttle slow to get a good reading, needle should move without no hesitation, if the test is bad replace tps sensor. if the sensor gets to bad, it can have an effect on transmission shifting. after fixing sensor have the light turned of with an obd2 scanner.

Posted on Feb 20, 2010

BCAS1298
  • 3092 Answers

SOURCE: 2003 Chevy malibu electrical schematic Fuel pump

Only if theft light is flashing, then it would need to be reset, to reset turn key to on and wait till theft light stops flashing about 10mim or so, then turn key to off and back to start engine.

Posted on May 27, 2010

Molson02536
  • 3854 Answers

SOURCE: where is the fuel pump located on a chevy malibu

It's located in the gas tank and to replace it, your going to have to drop the gas tank.
Thank you for using fixya and if you are going to replace the fuel pump your self. Make sure you also replace the wire harness from the frame to the fuel pump.

Posted on Jun 03, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 chevy malibu gas gauge always on empty, replaced the fuel pump


Need to replace the sensor inside the gas tank. I have a 2008 Malibu with the same problem. It was a faulty fuel gauge sensor.

Jan 31, 2012 | 2003 Chevrolet Malibu

2 Answers

Gas gauge doesn't work changed out the fuel pump or the fuel card and still don't work it's a 1999 chevy malibu


Just had a new fuel pump installed in 2002 Chevy Malibu. Worked great for about a week and then the fuel gauge started reading "empty" when the car has a full tank of gas. What happened?

Jun 13, 2010 | 1999 Chevrolet Malibu

2 Answers

Where is the fuel pump located on a chevy malibu


It's located in the gas tank and to replace it, your going to have to drop the gas tank.
Thank you for using fixya and if you are going to replace the fuel pump your self. Make sure you also replace the wire harness from the frame to the fuel pump.

Jun 03, 2010 | 2004 Chevrolet Malibu

3 Answers

How do you change the fuel pump on a 2002 chevy malibu


It is inside the fuel tank. There is no access panel. The fuel tank has to be removed from the vehicle and slid out to the right side(to clear the exhaust on the left). Once the tank is out of the vehicle, the fuel module can be removed from the top of the tank.

Oct 03, 2009 | 2002 Chevrolet Malibu

2 Answers

Replacing fuel pump, car turn over but want start


the fuel pump should be under back seat after you remove seat lift carpet there is an access panel remove that next you should see ring that holds pump in tank spin this to remove unplug pump and replace

Jun 29, 2009 | 2003 Chevrolet Malibu

2 Answers

2004 chevy malibu; gas hand moves from empty to full then back to empty


Hi the gas gauge is erractic
you need to replace the fuel level sensor

May 05, 2009 | Chevrolet Malibu Cars & Trucks

1 Answer

Fuel pump on chevy malibu


on 2000 malibu,the fuel pump is in the tank it will take you as long as it takes to drop tank! fuel pump is on top of tank,before starting remove fuel pressure by removing fuel pump fuse and run until it quits.it will take approx. 2-3hours to do a decent job. exhaust pipe is not on top it is on the left of the tank.

Mar 23, 2009 | 2000 Chevrolet Malibu

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

100 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...