Question about 1999 Suzuki Vitara

Open Question

What is crankshft torque settings on suzuki h20a engine

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: 1994 Suzuki Vitara V6 H20A Engine smoking intermittently from exhaust

I have a Mazda which in Australia (here) is called a 323 Astina, overseas a 323f, Familia, etc.
It uses a 2.0L Mazda KF Engine very similar to (in fact co-developed with) the Suzuki H20A engine, except designed to be transverse, variable resonance induction and other different tuning inc. 7000 redline, and probably not as reliable as an H20A.
I've had the engine rebuilt because I want to keep this car for a while and it needed it. Oil slipped past the rings which burned out grooves on one of the exhaust valves on Cyl-6 to the point where that cylinder had no compression...
... but I still get smoke occasionally, as you describe yours except not as often nor on the open road at speed. It happened ever since the first time I changed the oil after the rebuild. The tech who rebuilt it used a grade of oil I couldn't find and, liking synthetics, I used a lighter oil.
About the time you were writing your message, I replaced the rubber intake pipe feeding the throttle body and I noticed the inside of the intake manifold lined liberally with oil. The old pipe had oil only at one end.
The pipe I replaced didn't just go from the air mass sensor on the filter box to the throttle body. There was also a large pipe to an air reservoir (a lengthy pipe sealed at one end so that if you open the throttle quickly, you don't have to wait for more air to be filtered before it enters the engine, supposedly) and a tiny pipe to PCV valve.
It's not a long pipe so it's easy to look inside. The reason I'm boring you with all of that detail is because you'll almost certainly have a different one, but this is still most probably something you'll find feeding your intake manifold a supply of oil. The PCV (Positive Crankcase Ventilation) valve runs from one of the rocker covers (not that we have rockers) into a pipe feeding into this intake pipe. It's supposed to **** air in from the intake pipe due to a vacuum created by another pipe connecting from another part of the crankcase to the intake manifold (after the throttle body so it has a lower pressure than the intake pipe) and that might be happening in my engine but oil is, or was before the rebuild, seeping back into the intake pipe.
Being a transverse version of your engine, the PCV valve is on the front bank and the pipe from it to the intake pipe is quite short. The PCV valve is also situated above (if I remember correctly) a cam lobe so at higher revs, the oil gets flicked up into the PCV valve.
... so use an oil which is thicker at high temperature, do a compression test, or as I'm considering, run the pipe from the PCV valve into a canister to catch the oil before feeding the gasses into the intake manifold. That way less of the thinner oil will be burned off and I'll have a better chance at getting away with using it.
I use 15W40 Oil - viscosity of 15 weight (units?) when hot, 40 in Winter (which the W stands for). I should use 20Wxx, perhaps, to burn less oil.
This engine likes thin oil, it just goes on to liking it enough to inhale it. This engine also likes higher revs.
Hope that helps.

Posted on Feb 09, 2009

  • 102 Answers

SOURCE: suzuki h20a engine diagram

Engine diagram? You don't know what's involved in doing this job do you? This is MAJOR surgery! As the camshafts have to be removed, the timing cover has to be removed. As the rocker covers have to be removed, you will have to raise the inlet manifold. I say "raise" here, as if you want to remove the inlet manifold, you will have to remove the throttle body, and room will probably not let you do that (without removing the engine). As the timing cover has to be removed, the studs in it that go down through the sump will have to be removed - or remove the sump (which means removing the engine). If you're pulling all the timing gear off (to remove the cams), I would recommend replacing all the tensioners and chains while in there. OK, now you're ready to replace the valve stem seals. Remember, you'll have 24 of them to do. They are deeply recessed in the head and hard to get to. A little tool may have to be fabricated to pull the old ones off. The HVLAs (hydraulic valve lash adjusters) should be kept in their original positions, and stored under oil whilst you work elsewhere. Good luck. I have never had to do this job in-car - thankfully.

Posted on Jan 01, 2010

kirkx
  • 2019 Answers

SOURCE: H20A suzuki spark plug gap

In general, a smaller gap, like .032 inches will give you more power, better starting, especially in cold weather or with a turbo charger.
A larger gap, like .045 inchers will giver you better mileage and better reading on pollution tests.

While the oxygen sensor will pick up on any change in spark plug gap, you can compensate with a variable resistor in series with the oxygen sensor. So you can tweak the power vs mileage any way you want.

Posted on Feb 04, 2010

  • 880 Answers

SOURCE: Hi I am looking every where on the internet to

Try these guys;
salesweb@miamiautoparts.net

Posted on Nov 18, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Firing order suzuki h20 v6 engine


mine has cops and is fixed. my h25 , is same,
2nd google hit.
Firing Order 1-6-5-4-3-2
on my H25, #1 is front left. LHD , drivers side.
ill check the FSM
cyl 1 is bank one
cyl 1 is always the most forward cylinder, in V engines. (next time you know)

one other bit-o-history
The Mazda K series was co-developed with Suzuki, with Mazda reportedly handling the bulk of the design. The early 2.0 L Suzuki H20A and Mazda KF are similar in design

your car is SV620
H20
has 6 cops, coils over spark plugs.
and a single ignitor module, driven by the ECU.
the ECU sets firing, order. there is no distributor.
the Cam sender is timed, statically.
i suspect this question comes, up during, a new timing chain,
am i right?
I'm told some markets, have coil packs not cops..??
the EPC catalog shows no such thing.
but we don';t have the H20 here.
if you look down on the engine you will see the left bank1
is sitting far forward. from bank 2
take a look. it is. by 1/2 a bores distance,
page 1D-66 in my FSM shows this graphically,..
http://www.fixkick.com/look/odds-ends/suzuki/h20.jpg


0f1a4902-efd3-4ef1-85fe-702f7fffdb42.jpg

Feb 22, 2014 | 1995 Suzuki Vitara

1 Answer

Suzuki m13a engine diagram


I HAVE SUZUKI SWIFT 1.3 WITH CHECK ENGINE LIGHT ON.IT MOVES FOR 2 KM AND SWITCHES OFF.IT STOPS FOR SOMETIME AND IT STARTS AND MOVES AGAIN.WHATS THE PROBLEM .DOES IT HAVE A CRANKSHFT SENSOR AND WHERE IS IT POSITIONED.PLIZ HELP

Oct 21, 2013 | Cars & Trucks

1 Answer

Llow oil pressure


It probably has nothing to do with the water pump job. It could be that the engine has reached the age of being worn out, or the oil pressure switch may be failing.
You would want to use a mechanical gauge to check actual oil pressure in the engine hot and cold.

Jul 17, 2013 | 1999 Suzuki Vitara

1 Answer

Hi, I am looking for a free owner's manual for an


Go to the company's web site they should help out there

Jun 17, 2011 | 1996 Suzuki Sidekick

1 Answer

Whats the clearance of suzuki vitara engine tune-up: ___intake/ exhaust____?


VITARA G16A 88-94 Inlet (mm)0.13 - 0.17 Exhaust (mm)0.16 - 0.20

VITARA G16B 91-98 Inlet (mm)0.08 - 0.12 Exhaust (mm)0.08 - 0.12

VITARA J20A 97-98 Inlet (mm)0.08 - 0.12 Exhaust (mm)0.08 - 0.12

VITARA H20A - H25A N/A

Dec 08, 2010 | Suzuki Vitara Cars & Trucks

2 Answers

H20A suzuki spark plug gap


gap is 0.039-0.043 [in] ngk bkr6e-11

Feb 04, 2010 | 1999 Suzuki Grand Vitara

1 Answer

Top end noise Valve clearance


Top-end tune? This engine has oil-pressure-fed valve lash adjusters. There are some snake oils (engine oil additives) out there that claim to be able to free-up lifters and lash-adjusters, and you may have some success with following their instructions. After that, I would be checking what grade of oil you should be using in you climate and doing regular (possibly more frequent) oil changes.

Apr 29, 2009 | 1999 Suzuki Vitara

Not finding what you are looking for?
1999 Suzuki Vitara Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...