Question about Cars & Trucks

Open Question

2003 daewoo carlos front door handle

How do i remove it?

Posted by on


5 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 123 Answers

SOURCE: Inside Door handle replacement

yapp you do but it is not a big deal

Posted on Apr 22, 2009

  • 267 Answers

SOURCE: How do you remove the front door panels on 2003

all door panels are the same only different!!! no really there usually is a screw at the handly and two or three around the armrest or whatever you grab to shut the door. check around the edge of the entire panel for any screws or clips then when all is removed there are clips that pull out to release the panel. start at the bottom and pull or if you have a pry tool use it to start moving the panel away from the door. any other specific questions please reply i will watch my emails and get back to you.

Posted on May 03, 2010

  • 1168 Answers

SOURCE: Hi,can anyone tell me how to remove the lock

Hello Mel.
Some of these can be a pain. We all need small hands to work in some places.
Here is the list in the manual.
Front Door Outer Handle Replacement

NOTE: Put on gloves to protect your hands.

  1. Remove these items:
    • Door panel
    • Plastic cover, as necessary
  1. Raise the glass fully.
Remove the bolt, then remove the center lower channel (A) with the center lower glass run channel (B) by pulling it downward.
Remove the screw, and release the hook (A), then remove the lock rod protector (B) by detaching the clip (C).
Disconnect the outer handle rod (A) and cylinder rod (B).
Release the retainer clip (A) with a hook- shaped tool. Remove the lock cylinder (B).
Remove the screw, then separate the lock cylinder (A) and cylinder switch (B).
Disconnect the cylinder switch connector (A), and detach the harness clips (B), and remove the cylinder switch harness (C).
Remove the maintenance seal (A), and remove the bolt, then remove the cylinder protector (B).
Remove the bolt, then remove the spacer (A).
  1. While pulling the outer handle (A), remove the handle from the holes in the door panel. Take care not to scratch the door.
  2. Install the handle in the reverse order of removal, and note these items:
    • Make sure the cylinder switch harness is routed properly.
    • Make sure the connector is plugged in properly, and each rod is connected securely.
    • Make sure the door locks and opens properly.
    • When installing the lock cylinder, leave the outer door handle bolts loose so the inner protector does not interfere with the lock cylinder installation, then tighten the handle bolts.
    • Install the lock cylinder retaining clip on the handle, then install the lock cylinder. Be sure the clip is fully seated in the slot on the lock cylinder.
    • When reinstalling the door panel, make sure the plastic cover is installed properly and sealed around its perimeter.
    • Do the power window control unit reset procedure.
There you are!
Hope you get it done!

Posted on Nov 30, 2010

prostreet 55
  • 299 Answers

SOURCE: 2003 Toyota Sequoia, Front Passenger


Posted on Mar 19, 2011

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Replace left front fender

Replace left front fender - Fixya
Dec 29, 2015 - replace left front fender - Hyundai Motor 2003 Elantra question. ...Question about Hyundai Motor 2003 Elantra. Open Question ... How do i remove left front fender clip on a Lincoln ls 2002? Jan 04, 2015 ' 2002 Lincoln LS.

Replace 2003 hyundai elantra front passenger outside door ...
Mar 26, 2013 - Question about Hyundai Motor 2003 Elantra. Open Question.Replace 2003 hyundai elantra front passenger outside door handle. Need to replacebroken exterior door handle on front passenger .... replace left front fender.

Dec 29, 2015 | Hyundai Motor 2003 Elantra

1 Answer

How do you take off door panel 1996 Monte Carlo se?

1. Remove the screw holding the door-open handle bezel, and remove the bezel. Unhook the power door lock switch (if equipped) and set the bezel aside.
2. Carefully remove the power window switch from it's bezzel. There are 4 small clips, 2 on each side of the switch. Once you remove the switch from the bezel, the bezzel can be gently pried out the top of the panel w/ a small screw driver from the front.
3. Starting at the front w/ a small screw driver, pry out (gently!) the trim inlay that's above the arm rest... it was wood-grained plastic on this model.
4. Use a #30 torq bit to remove the large screw towards the top of the opening where the trim inlay was.
5. Remove the 4 Philips head screws around the perimeter of the door panel.
6. Lift up on the door panel... you may have to shake it a bit.... and after moving upwards no more that an inch... the panel should come off.

Jul 20, 2012 | 1996 Chevrolet Monte Carlo

1 Answer

ReMoving door panel to replace door lock actuator for 2003 ford thunderbird

please rate highly if this helps.

Front Door Trim Panel adobe.gif Printable View (126 KB)
  1. Disconnect the battery. For additional information, refer to Section 414-00.
  1. Remove the components in the order indicated in the following illustration and table.

    Item Part Number Description 1 23712 Sail panel 2 221A18 Door handle cup cover 3 W706476-S424 Screw 4 237A98 Door handle cup assembly
    Removal Note 5 18978 Speaker cover 6 - Speaker electrical connector (Part of 18808) 7 W706476-S424 Screws (7 req'd) 8 23942 Door trim panel
    Removal Note
  1. To install, reverse the removal procedure.
Item 4: Door Handle Cup Assembly Removal Note
  1. Lift up at the front of the door handle cup assembly, move it forward to remove and disconnect the electrical connectors.
Item 8: Door Trim Panel Removal Note
  1. If equipped, disconnect the electrical connector.

Jul 01, 2011 | Ford Thunderbird Cars & Trucks

1 Answer

How to remove front door panel to access window motor on 2003 cadillac escalade esv

pop out the manual door lock slider and remove the screw behind it, Pop out the triangle trim piece at the front of the window frame. Remove the screw located at the front of the armrest behind the pull handle. Remove the trim piece behind the door release handle. Then slide the door up....and all will become clear to you.

Jan 02, 2010 | 2003 Cadillac Escalade Esv

1 Answer

Removing front door panel on a 2003 suzuki aerio

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls

Sep 20, 2009 | 2003 Suzuki Aerio

1 Answer

Front driver's door won't lock on my 1999 Daewoo Lanos SE

it is attached with a wire clip and there s a very affordable removal tool which slips behind the crank handle and pushes it can be dug out with a hook scribe but a bit frustrating and can cause minor damage to the trim

Jul 01, 2009 | 2000 Daewoo Lanos

1 Answer

Door handle has lust snapped off n/s deawoo nubari 2003 1.8

well get a new one and change it ,its not difficult to do once the door panel is removed

Jun 06, 2009 | 2000 Daewoo Nubira

1 Answer

Need to remove window knob from 1979 monte carlo.

Getting to be an old vehicle now days. The mount that the window knob mounts on is usually a star type gear that the handle is pushed onto. There should be a very small hole in the round part of the handle that an allen set can slide into. Then loosened the hanle should pull off the star gear. Once the handle is removed the inside door panel should easily pull out over the gear.

Jun 01, 2009 | 1983 Chevrolet Monte Carlo

1 Answer

Changing shifter knob in 2003 monte carlo SS

Just took one of those off my nephews car...usually the handle has a small clip at the front bottom that needs to be pulled out. PS threw the mag handle in the garbage (because no button, and handle kept falling off)

Mar 15, 2009 | 2003 Chevrolet Monte Carlo

2 Answers

I need instructions on replacing driver side rear view mirror on 2003 chevrolet monte carlo

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can access the bolts that secure the mirror onto the door

Feb 26, 2009 | 2002 Chevrolet Monte Carlo

Not finding what you are looking for?

Open Questions:

Cars & Trucks Logo

Related Topics:

64 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides