Question about Cars & Trucks

Open Question

Cam and crank torque settings for rodeo 3.5 v6

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
StormStrikes
  • 104 Answers

SOURCE: TORQUE SETTINGS ISUZU RODEO FOUR CYLINDER

I dont know the specific answer for your question, but I own a 1995 Rodeo and there is an online community you could probably check out that Im sure would have the answer for you.

Check out www.planetisuzoo.com, sign up and post your question there. There are several knowledgeable people there and some good information as well.

Posted on Jan 03, 2009

Ad
emissionwiz
  • 76846 Answers

SOURCE: i need torque specs for 94 rodeo

flywheel 80-90 foot lbs (new bolts 90), press plate 45 foot lbs

Posted on Feb 14, 2009

mx5turbo92
  • 545 Answers

SOURCE: i'm looking for the 2000 isuzu rodeo 3.2L v6 connecting rod bearings torque specs.

1. Check the connecting rod alignment If either the bend or the twist exceeds the specified limit,the connecting rod must be replaced. Bend per 100 mm (3.937 inch) Limit: 0.15 (0.0059) Twist per 100 mm (3.937 inch) Limit: 0.20 (0.0078)

2. Measure the connecting rod thrust clearance. Use a feeler gauge to measure the thrust clearance at the large end of the connecting rod If the clearance exceeds the specified limit, the connecting rod must be replaced. Standard: 0.16 mm - 0.35 mm (0.0063 inch - 0.0138 inch) Limit: 0.40 mm (0.0157 inch)

3. Measure the oil clearance between the connecting rod and the crankshaft.

    1. Remove the connecting rod cap nuts and the rod caps (12). Arrange the removed rod caps in the cylinder number order.
    2. Clean the rod bearings and the crankshaft pins.
      1. Carefully check the rod bearings. If even one bearing is found to be damaged or badly worn, the entire bearing assembly must be replaced as a set. Reinstall the bearings in their original positions. Apply plastigage to the crank pin.
      2. Reinstall the rod caps (12) to their original positions. Tighten the rod cap nuts. Torque: 54 Nm (40 ft. lbs.) Note: Do not allow the crankshaft to rotate.
      3. Remove the rod caps.
        1. Measure the width of the plastigage and determine the oil clearance. If the oil clearance exceeds the limit, replace the rod bearing as a set. Standard: 0.019 mm - 0.043 mm (0.0007 inch - 0.0017 inch) Limit: 0.08 mm (0.003 inch)
        2. Clean the plastigage from the bearings and the crankshaft pins.

Posted on Jun 04, 2009

stevenhurc
  • 450 Answers

SOURCE: looking for torque settings for Holden rodeo 1999

big ends 54Nm/40Ft-lbs
mains 39Nm/29Ft-lbs and mains side bolts are same torque

Posted on Jun 25, 2009

stevenhurc
  • 450 Answers

SOURCE: torque settings for a holden rodeo 3.5 ra. Head

stage 1 = 29Nm(21 lb ft/3.0 kg-m)
final = 64Nm(47 lb ft/6.5kg-m)
do not reuse head bolts or apply any lubricant to the bolts. Do up bolts in following order for each head.
6 1 3 7
front
5 2 4 8

Posted on Dec 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do i replace the camshaft sensor on a 2004 rodeo


2004 had two engine but the early 2004 might have the 4 bangers , but the 4 banger dropped soon after July 2003 build day..

3.2 L 6VD1 V6 (gasoline)
3.5 L 6VE1W V6 (gasoline) a twin cam V6. !! unique.


in the next post i show all sensors. (most)

Aug 09, 2015 | 2004 Isuzu Rodeo

1 Answer

Camshaft torque isuzu 6ve1


wow, no year stated,
the cam has a front drive, bolt torque and cam bearing cap torque.
The 6VE1W 3.5L DOHC 24V V6 was introduced in 1998 with 215 hp (160 kW) and used until 2004 with the termination of the Isuzu Axiom. Gasoline direct injection was added for 2004 only and boasted output to 230 hp (172 kW). This was a stroked version of the 6VD1.

ill answer for 1998, rodeo 3.5L
alldata.com , try reading all the steps, not just torque . RTV steps
and sequence, of cap torque.

answer for caps
  1. Apply RTV gasket material to the mating surfaces of the cam bracket and head. Do not allow the gasket material to protrude.
  2. Install the caps and bolts. Torque the bolts, in sequence order, to 89 inch lbs. (10 Nm).

Apr 11, 2014 | Isuzu Rodeo Cars & Trucks

1 Answer

Hello and help, I need the main bearing, big end and flywheel torque settings for an Isuzu 3.1 td 1997, my manual only seems to have v6 petrol engines in it for some reason. many thanks Ron...


I have a 1997 Rodeo with the V6 3.2L engine. The crankshaft main bearing caps are torqued to 29(lb-ft).

The crankshaft pully is torqued to 123 (lb-ft).

Feb 26, 2011 | Isuzu Trooper Cars & Trucks

1 Answer

We need the sequence for a Head bolt torque on a 1996 Izusu Rodeo


For the V6 3.2L engine it is 6 - 2 - 3 - 7 on top, and 5 - 1 - 4- 8 on the bottom. These are M11x1.5 bolts and should be torqued to 47lb-ft.These bolts should not be re-used, only replaced.

The three M8x1.25 bolts on the left end are sequence numbers 11 - 10 - 9 from top to bottom and should be torqued to 15lb-ft.

Reference model 1997 Rodeo

Feb 22, 2011 | Isuzu Rodeo Cars & Trucks

1 Answer

Does anyone know the crank main bearing nut torque Alfa V6 3l


Torque to 25Nm, then tighten through a further 79 degrees. You need an angle gauge to do it properly.

Jan 29, 2010 | 1986 Alfa Romeo GTV6

1 Answer

Torque settings for a holden rodeo 3.5 ra. Head


stage 1 = 29Nm(21 lb ft/3.0 kg-m)
final = 64Nm(47 lb ft/6.5kg-m)
do not reuse head bolts or apply any lubricant to the bolts. Do up bolts in following order for each head.
6 1 3 7
front
5 2 4 8

Dec 03, 2009 | 2004 Isuzu Rodeo

1 Answer

Looking for torque settings for Holden rodeo 1999 isuzu v6 big ends and mains,


big ends 54Nm/40Ft-lbs
mains 39Nm/29Ft-lbs and mains side bolts are same torque

Jun 03, 2009 | 1999 Isuzu VehiCROSS

1 Answer

I need torque specs for 94 rodeo


flywheel 80-90 foot lbs (new bolts 90), press plate 45 foot lbs

Feb 14, 2009 | 1995 Isuzu Rodeo

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...