Question about 2009 Honda Element SC

Open Question

How do you install the front license plate bracket

Posted by Anonymous on


2 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 225 Answers

SOURCE: how do I install my front license plate holder

just screw it into the bumper it wont hurt anything

Posted on Nov 04, 2009


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to install front license plate 2001 deville

First you need a license plate bracket that mounts to the bumper, and then you screw the license plate to the bracket.

Feb 24, 2015 | 2001 Cadillac DeVille

1 Answer

How do i install a license plate bracket on a 2013 dodge journey

Self tapping screws will go right thru the thin plastic bumper cover.

Feb 20, 2015 | 2013 Dodge Journey

1 Answer

How do I mount a front license plate on a 2001 Mitsubishi Galant?

Normally there are screws already holding your old plate in there...(4 corners)
If your car doesn't have plate, usually the front bumper has a license plate bracket on it- normally it is 2 parts : 1 fastened to your car, the other comes off and you put your plate in between them and screw all of them back together.

If your car doesn't have a bracket, then it's prob a new bumper, so you can go buy one and you just drill it on (it'll have instructions if you have to buy 1) Just make sure you center it and it's straight.

Dec 04, 2014 | 2001 Mitsubishi Galant

1 Answer

Replace license plate light

what country? ( export below means , NOT USA)
its in the FSM
A single standard equipment rear license plate lamp unit is integral to the
license plate mounting bracket just below the left rear lamp unit on vehicles manufactured for domestic
markets. A bracket with two rear license plate lamps is located on the rear bumper directly below the
spare tire on vehicles manufactured for export markets.
and HOW TO: quote
1. Disconnect and isolate the battery negative cable.
2. Remove the license plate from the rear license plate bracket.
3. Remove the four screws (4) that secure the rear license plate bracket and lamp unit (3) to the four spring
nuts (2) in the rear body sheet metal (5).
4. Pull the bracket and lamp unit away from the rear body sheet metal far enough to access and disconnect
the body wire harness connector (1) from the connector on the back of the bracket and lamp unit housing.
5. Remove the bracket and lamp unit from the vehicle.
unquote the FSM.
Buy one for $20-

Aug 19, 2013 | 2010 Jeep Wrangler

1 Answer

Pennsylvania has no front license plate but new jersey does. purchase a 1996 jeep sport in PA but now i have to purchase and install a front license plate and bracket for NJ. Is there a special brand of...

for a simple item like that, get it from a local scrapyard. Holes are already where they need to be as it would actually be very expensive to make "special runs" of bumpers for areas that don't use front plates. (same goes for wiring harnesses...they are made with plugs for all options and whatever does not get ordered is just not plugged in. Shouldn't cost you more than $5.00!!!

Dec 28, 2010 | 1996 Jeep Cherokee Sport

1 Answer

How to install a front license plate bracket on a 2001 Mitsubishi Eclipse.

if it is a factory bracket there are 4 dimples on the middle of the bumper,you have to drill 1/2 in holes to install 4 grommets to hold bracket in place with screws-the factory bracket kit comes with bracket,4 grommets and the four screws-good luck

Apr 04, 2010 | 2001 Mitsubishi Eclipse

2 Answers

Where can I mount a bracket for a front vanity license plate? And, where can I get one?

most cars have the front bracket right from the factory. cheapest and best way is to drop by your local junk/wrecking/recycling yard and ask them for one for your car. while you are there ask them where it mounts and for the bolts that they take off the other car that hold the bracket on.

Dec 03, 2009 | 2008 Pontiac Grand Prix

1 Answer

Jaguar Front License plate bracket

I had the bracket upside down was the problem and now is attached properly

Nov 21, 2009 | 2001 Jaguar XK-Series

1 Answer

Installing front license plate on 2008 300C

there is an actual liscence plate bracket u can buy at a chrysler dealership thats fits perfectly on bumber it has teeth that perfectly center the bracket right below the grill it looks great i just had one put one on my 2005 300

Oct 22, 2008 | 2007 Chrysler 300c AWD Sedan New Cars

Not finding what you are looking for?
2009 Honda Element SC Logo

Related Topics:

108 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts


Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides