Question about 2010 Ford Fusion SEL

Open Question

How to replace a EVAP canister purge valve on a 2010 ford fusion

What tools do i need? How complicated is this?

Posted by Anonymous on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

savdragon
  • 37 Answers

SOURCE: Mustang GT 4.6 EVAP Canister Purge Valve Location?

You will need to remove the right front wheel & wheel well liner. The canister purge valve is behind the cover. It should have two tube going into the bottom and one on the side near the top.
You can fix it!
If this helps you out please rate me!
Brett

Posted on Mar 19, 2009

  • 532 Answers

SOURCE: I need to locate the canister purge valve and the

look above the spare tire under the back of the box

Posted on Oct 24, 2009

  • 312 Answers

SOURCE: Getting an engine code 1450 on a 2003 ford

Did you check the block box connected to the vent solenoid? There's a hose that comes off it that appears to run nowhere, that's the fresh air vent. If it's blocked it won't allow air into the system which will set the trouble code. If that's clear, the vent solenoid itself is bad and needs to be replaced.

Posted on Jun 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is purge valve located?


How to test and replace the EVAP Canister Purge Volume ...

? 13:49
https://www.youtube.com/watch?v=QnVUBYdFHGI
Mar 29, 2014 - Uploaded by CarsNToys
The EVAP canister purge control volume control valve is operated by a step motor for control of flow rate of fuel vapor fromEVAP canister.

How To Install Replace Vapor Canister Solenoid Purge ...

? 2:14
https://www.youtube.com/watch?v=TZ6ZB_acC9w
Sep 16, 2014 - Uploaded by 1A Auto Parts
http://www.1aauto.com/vapor-canister-purge-solenoid-valve-ac-delco- ... How To Test and Replace EVAP Canister Vent ControlValve P0446 ...

EVAP Purge Solenoid Removal - YouTube

? 4:24
https://www.youtube.com/watch?v=Xj605HENFno
Feb 26, 2008 - Uploaded by richpin06a
EVAP Purge Solenoid Removal Saturn S-series. ... How To Test and Replace EVAP Canister Vent Control Valve P0446 - Duration: 6:18. by ...


Dec 18, 2015 | Cars & Trucks

1 Answer

2007. What are the probable causes of DTC P0446?


DTC P0446: Evaporative Emissions (EVAP) Vent System Performance
Circuit/System Description
This DTC tests the evaporative emission (EVAP) system for a restricted or blocked EVAP vent path. The control module commands the EVAP canister purge solenoid valve Open and the EVAP canister vent solenoid valve Closed. This allows vacuum to be applied to the EVAP system. Once a calibrated vacuum level has been reached, the control module commands the EVAP canister purge solenoid valve Closed and the EVAP canister vent solenoid valve Open. The control module monitors the fuel tank pressure (FTP) sensor for a decrease in vacuum. If the vacuum does not decrease to near 0 inch H2O in a calibrated time, this DTC sets.
Diagnostic Aids
?€¢
An intermittent condition could be caused by a damaged EVAP vent housing, a temporary blockage at the EVAP canister vent solenoid valve inlet, or a pinched vent hose. A blockage in the vent system will also cause a poor fuel fill problem.


?€¢
An EVAP canister, vent hose, or vent solenoid valve that has restricted flow may cause this DTC to set. Using a purge solenoid command with a scan tool will allow vacuum to be applied to the system instead of pressure. With the engine running, the EVAP canister vent solenoid valve open, and the EVAP canister purge solenoid valve commanded to 100 percent, the fuel tank vacuum should not increase to more than 5 inches H2O.


?€¢
An EVAP canister filter that is restricted can cause this DTC to set. Refer to Evaporative Emission Canister Replacement .


?€¢
Disconnecting one component at a time while the EVAP system is under flow will help to pinpoint a restriction in the system


Do you have a scan tool that reads data PID'S ?
Your FTP - fuel tank pressure sensor could be at fault !

    Ignition ON and fuel cap removed, verify that the FTP sensor parameter is between 1.3-1.7 volts. ?‡'
    If not within the specified range, go to the FTP sensor section in Circuit/System Testing.

  1. Install the fuel cap.
  2. With the engine running, the EVAP canister vent solenoid valve open, and the EVAP canister purge solenoid valve commanded to 100 percent, the fuel tank vacuum should not increase to more than 12 inches H2O.
?‡'
If the fuel tank vacuum is greater than the specified range, go to the restriction section in Circuit/System Testing.



If

Sep 06, 2015 | Chevrolet Impala Cars & Trucks

1 Answer

Why is my 2010 ford fusion is throwing code po455. no gas cap required


P0455 is Evaporative Emissions System Leak Detected (Large) and means that there is a large leak in the system probably with one of the EVAP hoses near the fuel tank or EVAP canister or maybe even A leaky purge valve.

May 06, 2014 | Ford Fusion Cars & Trucks

2 Answers

2006 Ford Fusion 2.3L I4 Engine Check engine light ODBC code is P0455. I have already replaced the gas cap. The computer codes were cleared by disconnecting the battery. The check engine light and same...


If you have already replaced the gas cap then you need to start looking for splits in your evap lines, and the evap canister for your vehicle. This procedure is easier done at a shop then by the DYI due to how many different lines that you have, and you may have a small slice in a line that only opens up under certain conditions. The p0455 is a very difficult code to diagnosis

Jun 06, 2011 | 2006 Ford Fusion

1 Answer

P0446 ford escort 98


This Pinpoint Test is intended to diagnose the following:
  • Canister vent (CV) solenoid (9F945) (electrical concern only)
  • Fuel filler cap (9030)
  • Fuel tank pressure (FTP) sensor (9C052)
  • EVAP canister tube (fuel tank to EVAP canister)(9A228)
  • Fuel canister purge outlet tube (EVAP canister to EVAP canister purge valve) (9D661)
  • EVAP return tube (EVAP canister purge valve to intake manifold) (9G271)
  • EVAP canister purge valve (9C915)
  • Vacuum source line (input port vacuum to intake manifold)
  • Harness circuits: CV, FLI, FTP, EVAP Canister Purge Valve, SIG RTN, vehicle power (VPWR), reference voltage (VREF) and power ground (PWR GND)
  • Powertrain control module (PCM) (12A650)
This Pinpoint Test is used as an assistance in diagnosing the following EVAP components:
  • EVAP canister and bracket assembly (9E857)
    • EVAP canister sleeve assembly (fitting)(9D925)
    • Canister vent (CV) solenoid - hose assembly (9F976 or 9K318)
    • EVAP canister (9D653)
    • Canister vent (CV) solenoid (9F945)(mechanical concern only)
  • Fill limit valve assembly (9A086)
  • Fuel filler pipe flapper valve (9B085)
  • Fuel filler pipe check valve (9189), assembly (9285)
  • Fuel tank filler pipe (9034)
  • Fuel tank assembly (with fuel vapor vent valve) (9K007)
  • Fuel tank assembly (without fuel vapor vent valve) (9002)
  • Fuel vapor control valve (9B190)
  • Fuel vapor vent valve (9B593)
  • Liquid/vapor fuel discriminator (9G332)
  • On-board refueling vapor recovery (ORVR) T - connector assembly (9S314)
Description For additional information on the Evaporative Emission (EVAP) System, refer to Section 1A .
For additional information on the Evaporative Emission System Monitor, refer to Section 1A .
Pinpoint Test Schematics Escort/Tracer (2V)
aa3060b.gif

May 28, 2011 | 1998 Ford Escort

2 Answers

Check engine lite came on code is p1443 what does this code mean


P1443 Evaporative Emission Control System Control Valve The Evaporative Emission Control System monitors the fuel vapor flow between the engine intake manifold and the EVAP canister. The system failure occurs when a leak or blockage between the intake manifold, the EVAP canister purge valve and the EVAP canister is detected by the PCM.

Code P1443 Possible Causes:

- Pinched, blocked or plugged fuel vapor tubes/hoses (except between fuel tank and EVAP canister)

- Damaged EVAP canister

- Disconnected, cracked or cut fuel vapor tubes/hoses (except between fuel tank and EVAP canister)

- Damaged EVAP canister purge valve

May 04, 2011 | 1997 Ford Escort

2 Answers

Ford escort wagon 1997 code p1443 displayed. what does this indicate & where is the cannister? thank you.


P1443 - EVAP Control System / Vacuum System Purge Control Solenoid Or Purge Control Valve Fault. A fuel tank pressure change greater than minus (-) 7 inches of water in 30 seconds occurred with a purge (fuel vapor) flow at less than 0.02 pounds per minute.

Possible Causes:
  • Blocked fuel vapor hose between the EVAP canister purge valve and the FTP sensor.
  • Blocked fuel vapor hose between the EVAP canister purge valve and the engine intake manifold.
  • Blocked vacuum hose between the EVAP canister purge valve solenoid and the engine intake manifold.
  • EVAP canister purge valve stuck closed (mechanically).

  • Possible Solution:
    Check for blockages between the fuel tank, the EVAP canister purge valve, and the engine intake manifold. Check for obstructions in the EVAP canister purge valve diaphragm and ports.

    The canister is on the passengers side near the firewall if I recall correctly.

    Jan 18, 2011 | Ford Escort Cars & Trucks

    3 Answers

    Po446 evap vent code where is the evap vent located


    Some might have an ses p0446, evap emissions vent circuit low. If you take it to the dealer they want 300-400.00 to fix the problem. GM has a service bulletin on this condition and have the updated part for 180.00, thats suppose to eliminate this issue.

    Basically the problem is, the evap purge vent valve gets clogged with dirt, especially if the truck is used in dirty conditions. Well I figured there had to be a cheaper way to cure this problem.

    Here it is:
    1) find the location of the vent valve; its under the truck, locate the charcoal canister on the front of the gas tank and trace the vent line to the vent valve.
    2) Take the bracket loose with a 5/8 wrench.
    3) Spin the valve around so the side with the hole is facing you.
    4) Take an air compressor and blow the vent valve out.
    5) reinstall and clear the code and it's fixed.

    Now I know the updated part from gm is supposed to keep the valve from clogging ever again, but why spend the money when all you have to do is blow out the vent valve every 50k-100kmi and save your $$$!

    Subject: DTC P0446 (Restricted/Blocked EVAP Vent Path) Set, Service Engine Soon (SES) Lamp Illuminated (Replace Hose/Evaporative Emission (EVAP) Canister Vent Asm) #02-06-04-037A - (02/02/2005)
    Models:
    - 1999-2003 Chevrolet Silverado Models
    - 1999-2003 GMC Sierra Models
    --------------------------------------------------------------------------------
    This bulletin is being revised to add model years. Please discard Corporate Bulletin Number 02-06-04-037 (Section 06 -- Engine/Propulsion System).
    --------------------------------------------------------------------------------
    Condition
    Some customers whose vehicles are operated in dusty type environments, such as farming or mining off-road type applications, may comment about the illumination of the instrument panel SES light, with a DTC of P0446 (Restricted/Blocked EVAP Vent Path) being set.

    Cause
    Dirt and dust intrusion into the EVAP canister vent hose assembly, resulting in restricted air flow, may cause this condition.

    Part Number 15086429 Hose Asm-Evap Emis Cnstr Vent


    Removal & Installation
    Purge Solenoid Valve-2.2L (L61) Engine
    1. Disconnect the evaporative emission (EVAP) canister purge valve harness connector.
    2. Disconnect the vacuum pipe from the EVAP canister purge valve.
    3. Disconnect the purge pipe from the EVAP canister purge valve.
    4. Remove the EVAP canister purge valve and bracket.
    5. Remove the EVAP canister purge valve from the purge bracket.
    6. Inspect for carbon release in the EVAP canister purge valve ports.
    To install:
    1. Install the EVAP canister purge valve on to the purge bracket.
    2. Install the EVAP canister purge valve and bracket. Tighten the purge bracket nut to 71 inch lbs. (8 Nm).
    3. Connect the purge pipe to the EVAP canister purge valve.
    4. Connect the vacuum pipe to the EVAP canister purge valve.
    5. Connect the EVAP canister purge valve harness connector.
    6. Remove the air cleaner outlet resonator.
    7. Disconnect the EVAP canister purge valve harness connector.
    8. Disconnect the engine purge pipe from the EVAP canister purge valve.
    9. Disconnect the engine vacuum pipe from the EVAP canister purge valve.
    10. Remove the EVAP canister purge valve mounting bracket attaching bolt.
    11. Remove the EVAP canister purge valve along with the mounting bracket.
    12. Installation is the reverse of the removal procedure. Tighten the bracket bolts to 71 inch lbs. (8 Nm).

    Purge Solenoid Valve-2.4L Engines
    1. Remove the front purge pipe from the evaporative emission (EVAP) canister purge valve.
    2. Remove the rear purge pipe from the EVAP canister purge valve.
      NOTE The EVAP canister may have released carbon particles, which caused this part to fail, and may cause damage to other components. Check the EVAP canister for loose carbon before returning the vehicle to service.
    3. Disconnect the EVAP canister purge valve electrical connector.
    4. Insert a screwdriver between the EVAP canister purge valve and the mounting bracket in order to release the lock tab.
    5. Remove the EVAP canister purge valve mounting bracket attaching nut, if replacing the bracket.
    6. Remove the bracket.
    To install:
    1. Install the mounting bracket and the attaching nut for the EVAP canister purge valve. Tighten the nut to 71 inch lbs. (8 Nm).
    2. Slide the EVAP canister purge valve onto the mounting bracket. Make sure the lock tab locks the valve in place.
    3. Connect the EVAP canister purge valve electrical connector.
    4. Connect the rear purge pipe to the EVAP canister purge valve.
    5. Connect the front purge pipe to the EVAP canister purge valve.

    Vent Solenoid Valve-2.2L & 2.4L Engines
    1. Raise the vehicle
    2. Loosen the EVAP canister vent valve hose clamp and slide the clamp down the hose away from the EVAP vent valve hose connection.
    3. Remove the hose from the EVAP canister vent valve.
    4. Remove the EVAP canister vent valve by placing a pry bar between the valve and mounting surface, and moving the valve forward.
    5. Remove the clip from the EVAP canister vent valve harness connector
    6. Disconnect the EVAP canister vent valve harness connector.
    To install:
    1. Connect the EVAP canister vent valve harness connector
    2. Install the clip into the EVAP canister vent valve harness connector.
    3. Install the EVAP canister vent valve by pushing the mounts into the original holes.
    4. Lubricate the hose end with lubricant.
    5. Install the hose to the EVAP canister vent valve.
    6. Slide the EVAP canister vent valve hose clamp down on to the hose connection at the EVAP canister vent valve.
    7. Lower the vehicle.

    Hope this help (remember commetn and rated this).

    Apr 21, 2010 | 2000 GMC Jimmy

    2 Answers

    Describe your 1996 Ford Explorer Problem..trouble


    Diagnostic Trouble Code (DTC) P0443 indicates a failure in the EVAP canister purge valve circuit.
    Possible causes:
    • VPWR circuit open.
    • EVAP canister purge valve circuit open.
    • EVAP canister purge valve circuit shorted to PWR GND.
    • EVAP canister purge valve circuit shorted to VPWR.
    • Damaged EVAP canister purge valve.
    • Damaged PCM.

    Jul 10, 2009 | 1996 Ford Explorer

    Not finding what you are looking for?
    2010 Ford Fusion SEL Logo

    Related Topics:

    752 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts

    yadayada
    yadayada

    Level 3 Expert

    75807 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22133 Answers

    fordexpert

    Level 3 Expert

    5495 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...