Question about Cars & Trucks

Open Question

Fit a quarter light window on 1998 ford transit

Trying to fit quarter light window on door any hints

Posted by Anonymous on


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 638 Answers

SOURCE: re fitting door glass to a triumph herald 13/60

i will give u the best link for step by step instructions for ur car repairs on ur own:

feel free 4 further assistance .rate the particular experts solution as fixya that helps u understand n solve ur problem

Posted on Jun 26, 2008

  • 5 Answers

SOURCE: Power quarter vent window

All I do is (A) mess with the front window buttons --down a little/up a little-- then (B) the rear window works fine. Until (C) the next time it doesn't. AKA If (C) do (A) until (B). :)

Posted on Oct 09, 2008

  • 582 Answers

SOURCE: ford focus c max towbar electrics


Posted on Aug 25, 2009

  • 11 Answers

SOURCE: Ford Transit Diesel 2.5 engine needs timing belt

hi if you send me the engine code what if think is a WL motor ill send it to you

Posted on Aug 26, 2009

  • 770 Answers

SOURCE: how do i fit a thermostat for a 1998 ford fiesta

Purchase new thermostat. Follow the top radiator hose to the engine and remove the bolts that secure the housing at the engine end of that hose, to the engine. Pay careful attention to the way that the old thermostat fits, pop it out and put the new one in the same way.

Posted on Sep 18, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I have a ssangyong kyron and how do you re-fit another quarter light window on the rear door

You'll have to remove the window frame to replace. I don't work on yours. But you have to remove the door panel remove the regulator and motor. Remove the inside trim at the bottom of window and pull the widow out threw the top. Remove the bolts for the lower window frame, pull them down and out. The grab the front of the window trim in the door and start pulling it down. When you get to the quarter window you will need to pry down with a screw driver and pull down to get it out. Once it comes loose from the door it will drop. There will be screws or rivets that hold the bottom channel of the quarter window.

Jan 05, 2017 | SsangYong Kyron Cars & Trucks

1 Answer

What other transmissions fit a 1998 ford explorer 4x4

A 3.0 manual transmission will fit on a 1998 Ford Probe vehicle. ---------------------------------------------------------------------------------
MaxiScan FR704 Code Scanner Reader

Mar 30, 2013 | 1998 Ford Explorer

1 Answer

Will a 1994 ford explorer rear hatch fit on a 1995 ford explorer?

Unfortunately no, the 1994 Ford Explorer hood latch will not fit on a 1995 model. You need to find a latch from between the years of 1995 - 97.--------------------------------------------------------------------------------------------
autel maxidas ds708

Nov 24, 2012 | 1995 Ford Explorer

1 Answer

How to replace subaru quarter glass

Hi Mom, I'm wondering how your spinach pie tastes? Replacing the quarter light is not an easy job, but if you're handy with wrenches and screw drivers here goes. Open the offending door and remove the power window switch by gently lifting it with a thin flat screw driver. Disconnect the cables by releasing the locking tap on the underside of the unit. Remove the back cover of the door release handle by either removing the single screw or un clipping it, Using a Philips screw driver, remove the two deep screws under the arm rest. Borrow the pastry knife from your kitchen and at the lowest part of the door insert it between the panel and the door frame, and then gently pry it towards yourself until you hear the press studs pop open. Repeat the same action all the way around the bottom and up the two side of the door and when loose, lift off the panel and place it out of the way of the kids. Re attach the switch controlling the window and lower the window to where you can reach the bolts (10mm) with a socket wrench. The bolts hold the regulator to the window. Loosen them and remove and lower the regulator all the way down, until you can pull the window up at an angle allowing you to remove it from the door. carefully lift and remove it and put it somewhere safe. remove the rubber weather strips and from the top of the door frame together with the strips inside the rail the window moves on. If you follow the rail of the window to where it is fitted to the door frame you will see another 10mm bolt at the bottom. Before removing that one mark the position as exactly as possible. (The position is critical for smooth operation of the window). Remove the weather strip around the outside of the frame of the door and on top you will see the upper bolt holding the rail (which should also be marked) Remove that and then the rail. The quarter light is held into position by a rubber which surrounds it.Being very careful of any glass which may have remained in the rubber gently remove it and after cleaning it, fit the replacement into the rubber. With the glass in place fitting it into the correct position is not going to be easy. A good idea is to smear a light coating of white petroleum gel onto the parts of the rubber which fit into the door frame before fitting it. When the quarter lite has been fitted and the rail placed in position reassembly is opposite to disassembly. Keep in mind that when fitting back the window it must be aligned with the rails which should be finally tightened after the window is fitted. Now tell me, while you're busy doing that, who's gonna bake the spinach pie? Best regards John

Sep 21, 2012 | 2002 Subaru Forester

2 Answers

What size speakers are in the doors

  • The factory speakers are 6x9 BUT the magnet on the factory speakers are much smaller than on aftermarket, higher quality 6X9 speaker making it almost certain the window will not roll down after installing an aftermarket 6X9.

  • Most go with a 6X5 because they are a bit smaller and there is a wider variety of them. Where ever you go to purchase that speaker. make sure the measurements are taking real well if going with another 6x9. There is always the option of the factory 6x9 but a nice aftermarket will fit in there so long as you mind the size.

  • If you have any comments please feel free to leave them here.
  • Hope this helps and thank you for using FixYa.

Regards, Tony

Oct 07, 2011 | 1997 Jeep Grand Cherokee

1 Answer


it will fit but i am not sure will cover whole door

May 07, 2011 | 1998 Ford Expedition

1 Answer

How to remove and replace driver side rear quarter panel just behind the sliding van door of a 1998 Dodge Grand Caravan? How much is a replacement part?

These are generally not for the do it yourselfer since they are spot welded in place and there are many sizes of panels to fit the area you need to replace. Have an auto body shop look at it for advice - many give free estimates.

Nov 29, 2010 | 1998 Dodge Grand Caravan

1 Answer

How do i release the spare wheel my jack handle wont fit I have a ford MK6 Transit

open the back door should see a large screw in the bumper use a flat head screw driver to crank it down

Oct 03, 2010 | Ford F Cars & Trucks

1 Answer

Are there any other seats that fit Ford Transit Connect other than the original ones as the seat I have is giving me back ache.

You can get another seat from a scrapyard. You will need to do some measuring to find what will fit.Pay attention to seat height above the floor as well. Too wide seats will interfere with the door. Bolt holes can be moved by drilling but always use at least 3" washers under the floor to make sure they don't pull through in an accident situation. Always be careful not to drill into brake lines or other items underneath. If you have electric seats, you will need to re-wire harness to make it work.

Oct 19, 2009 | 2003 Ford Focus

2 Answers

1999 explorer stock subwoofer

I would be very proud of that truck as the sub that came with the truck was only a 8". The only one that works is the factory model as it is a 1 1/2 - 2 ohm speaker; replacements are 4ohm. You will have to replace the amp as well if you put in an aftermarket sub. Oh and apparently the amp will have to have "speaker level" inputs as opposed to pre-amp inputs. I have a 1999 Eddie Bauer wih a blown sub and I'm trying to decide what to do as well. The speaker is $400 with tax in Canada! Good luck.

Mar 06, 2009 | 1998 Ford Explorer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides