Question about Ford Laser

Open Question

Remove door trim ford 1999 kn laser

Most answers I can find suggest there are screws around the interior door rest but there isn't. There is a hole that has no apparent screw but it feels like you push something up with the screwdriver. I tried to push up but I still can't get the door rest/handle section off ( not the part to release the door, the built in handle part). Any help greatly appreciated.

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Clanmartin
  • 2 Answers

SOURCE: Removing interior door trim '93 suzuki swift

Assume you have been able to remove window winder.
The surround of the the door handle (interior) is clip on at four points. Tabs are about an inch in from each corner and slide over a plastic nub to lock in place. . Start at top right corner. Get a small flat blade screwdriver with blade horizontal and gently - repeat gently, prise tab upwards while applying gentle pressure away from door and pushing slightly upwards. Tab should just slide off nub holing it in place. Do same for other side on top tab. Gently wriggle downwards so bottom tabs disengage. Installation is reverse.

Posted on Oct 12, 2008

Mikey108
  • 475 Answers

SOURCE: Replace Driver's side mirror - Jeep Liberty 2002

The door panel has plastic clips that hold it in place also. Put a thin blade screwdriver between the panel and door. Pry the panel away from the door. The panel will make a loud snapping noise, that is the clip coming out of the retaining hole. Sometimes the clips break.

Posted on Dec 09, 2008

  • 57 Answers

SOURCE: Trying to remove door panel. Seems stuck behind door handle.

Under armrest are two large philips screws. remove these and the panel will fall off.

Alternatively, one screw may be acccessed from the top down on the arm rest, remove small access circle, or tray insert.

Posted on Dec 15, 2008

MrScary66613
  • 1990 Answers

SOURCE: Help with drivers door panel removal 2003 Deville

Look really close for Screw Hole Covers. These are Small Plugs that they Install from Factory to Clean up the Visible Screw Holes. Please Rate My Response! Thanks!

Posted on Feb 02, 2009

  • 184 Answers

SOURCE: Remove Rover 45 driver door trim to replce wing mirror.

what you need to do here is pull out door trim from bottom & then give it a good bang at bottom it should slide out of top guide but you need to give it a good bang asthey are quite tight in there.

Posted on Mar 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do I remove the drivers door panel on a 2002 Taurus


door panels have hidden plastic pins that need to be removed with a fork-like flat tool you can get at any auto parts store. In addition, there are screws and bolts usually around the door arm rest (may be hidden by round plugs) and the surround for the door release handle.

Dec 23, 2010 | 2003 Ford Taurus

1 Answer

Rear hatch will not open,how is the interior trim


look for any plugs that may be covering screws around outside edge, as well as obvious screws, then the rest will probably be push/pull clips. Usually a quick **** will release them.

Feb 20, 2010 | 1998 Ford Explorer

2 Answers

My 1999 Chevy Silverado 3 door 4x4 power door locks wont unlock the door completely. The switch activates the door lock slide, but only part way. Any recomedations?


check for binding by interior door slide if looks good remove trim ring around interior handle and on plastic lock slide use a dry lube or graphite if still not releasing remove panel --2 screws in arm rest/door grab than carefully pull straight back starting at bottom corner might need a screw driver to release the plastic clips on panel if u have help once panel is off they can hold panel away or you can push out switch panel and remove door panel out of the way check the lock rod plastic clips for damage and or binding repair or replace problem replace panel -good luck

Nov 24, 2009 | 1999 Chevrolet Silverado 1500

2 Answers

How do you remove driver side door panel 1999 vw beetle


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls.

Oct 13, 2009 | 1999 Volkswagen Beetle

1 Answer

How do i remove the drivers side door panel on a jag s type


This is the same front or rear door. 1. remove rubber insert at the bottom of the arm rest/door handle 2. remove the 2. philip head screws. 3. run hand along bottom edge of door panel to ensure no other securing screws. 4. starting at the top rear edge of the door panel side a large flat screw drive/door panel tool(what ever you have) 5. lift sharply and you will here poping noises fromt the push clips lifting out of the socket. 6. as you work down the rear edge of the door panel you will see the trim around the interior door handle lift away. remove it. 7. the interior door handle will remain on the door. 8. remove the rest of the door panel.

Oct 10, 2009 | 2000 Jaguar S-Type

1 Answer

Door panel removal


front

SECTION 501-05: Interior Trim and Ornamentation 1999 F-Super Duty 250-550 Workshop Manual
REMOVAL AND INSTALLATION Trim Panel —Front Door Removal
  1. Remove the rear view mirror mounting hole cover (17K709).
  1. If equipped, remove the window regulator handle (23342); refer to Section 501-11 .
  1. If equipped, remove the window regulator switch plate (14524); refer to Section 501-11 .
  1. If equipped, disconnect the power windows, power door lock switch and power mirror connectors.
  1. If equipped, remove the front door trim panel reflector or the courtesy lamp lens.
  1. Remove the screws.
3e120ac.gif
  1. NOTE: Remove the front door trim panel (23942) by pulling it straight upward.
    Lift and remove the front door trim panel.
  1. If equipped, twist the courtesy lamp connector one half turn and remove it from the front door trim panel.

Apr 17, 2009 | Ford F-350 Cars & Trucks

1 Answer

Side mirror of 2005 ford explorer


Exterior Mirror Removal and Installation
All vehicles
  1. NOTE: Left side exterior mirror shown, right side similar.
    Remove the interior door trim panel. For additional information, refer to Section 501-05 .
Front Door Trim Panel Removal and Installation
  1. Disconnect the battery ground cable. For additional information, refer to Section 414-01 .
  1. Remove the inside door handle bezel from the trim panel.
  1. Remove the window switch assembly.
  1. Disconnect the window switch and power door lock electrical connectors.
  1. Remove the upper trim panel screw at the window switch opening.
5c94a3e.gif
  1. Remove the lower trim panel screws.
2de1016.gif
  1. s2n~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: To avoid damage to the door trim panel, do not pull directly outward for this step.
    Lift the door trim panel by pulling directly upward on the armrest to disengage the panel clips.
  1. Disconnect the power mirror electrical connector.
  1. Remove the trim panel.
  1. Remove the weather shield.
Vehicles with power, heated or approach lamp equipped exterior mirrors
  1. Disconnect the electrical connector.
All vehicles
  1. Remove the bolts.
a2275a5.gif
  1. Remove the exterior rear view mirror (17682).

Feb 23, 2009 | 2003 Ford Explorer

1 Answer

How to remove the door panel on a 96 Ford Thunderbird?


Carefully pull front door trim panel finish panel away from front door trim panel.
Disconnect wires from front door lock switches, outside rear view mirror controls and window regulator control switches, if equipped. Remove front door trim panel finish panel.
Remove front door trim panel retaining screw through front door trim panel finish panel opening.
Remove interior lamp lens cover.
Remove screw through interior lamp opening.
Slide front door trim panel upward to disengage hooks.
Rotate top of front door trim panel away from front door and lift bottom hooks from front door.
Disconnect window regulator jumper wire
Remove front door trim panel.

Feb 21, 2009 | 1996 Ford Thunderbird LX

1 Answer

How do i remove door trim on a 1998 ford laser lxi


there will be a few screws in the panel espically around the door handle. After that you will have to carefully pry under the door panel to release the clips that hold the panel on. I always start in the lower corner and work my way around. once you have the panel loose, you will have to lift the panel up off the door because of the window trim.

Jan 11, 2009 | 2006 Ford Laser

2 Answers

I need to replace passenger side mirror on 97 ford expedition


Both above answers are not right... I just replaced the Pass side power mirror assembly on my 97 Expedition. No heat, no directional.
The inside door panel must come off.
1. pry off interior triangular plastic trim piece inside of door at mirror area. Remove door panel screw at this area.
2. Pry off power window switch panel and remove door panel screw at this area.
3.Remove interior door light cover and remove screw at this area.
4. Remove plastic cover at door handle.
5. The interior door panel can now be lifted up to release it from it's fasteners.
6. Disconnect light and push power window switch assembly through the door panel and it can be set aside.
7. Disconnect mirror power at coupler.
8 Loosen three mirror mounting screws with 7/16 socket. DO NOT unscrew completely.. the will fall down the door cavity. Use a round magnet on holder to remove the screws completely.
9.Thread electrical connection into door panel and install mirror.
10. Smile when mirror works and drink a beer!
rayman

Dec 27, 2008 | 1997 Ford Expedition

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

132 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...