Question about 2005 Ford Freestar

Open Question

Fuel line retaining clip removal - 2005 Ford Freestar

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 169 Answers

SOURCE: Ford E-450 fuel filter removal

YOU NEED T INSERT THE SPECIAL TOOL WICH RELEASES THE RETAINER INSIDE THE BULGED OUT PART OF THE LINE. TRY NAPA FOR TOOL NO. Part: SER 3290 Product Line: NAPA Service Tools WATCH OUT FOR FUEL THAT MAY SPRAY OUT WHILE DISCONNECTING! GOOD LUCK

Posted on Aug 26, 2008

Ad
  • 1757 Answers

SOURCE: cant remove the rotor and retainer clip

You will need a large bearing retaining nut socket (1-in drive) about 2 7/16th in or 61/62mm (I got mine at NAPA with a 1/2 in to 1-in drive converter) BUT BEFORE loosening the nut there is a small keeper under the bottom edge the nut at the top (12-oclock) position of the nut. Use a magnet to retrac this and then loosen the large bearing nut. You sometimes have to slightly move the nut "a hair" left or right to remove this bearing keeper. Once the keeper is out the nut will easily come off. The rest is easy. Good Luck!

Posted on Nov 10, 2009

cobra777
  • 80 Answers

SOURCE: I am trying to change fuel filter on 1995 ford

Yes you do, The first clips you removed are the secondary clips. The lines have to be released from the inside. Heres the info.. Cobra :-)
Removal

  1. Open safety clip.

    v9067a.gif

  1. Fit Tool T90T-9550-B (5/16 inch) or T90T-9550-C (3/8 inch) to coupling so that tool can enter female fitting.

    v9068a.gif

  1. Push the tool into female fitting to release the retaining fingers from the formed male tube end.
  1. Pull male and female fittings apart.

    v9069a.gif

  1. Remove the tool from the disconnected fitting.
  1. Inspect the fitting for any internal parts that may have been damaged. Fuel tube should be replaced if internal parts are damaged.

Posted on Jun 06, 2010

BCAS1298
  • 3092 Answers

SOURCE: can i buy a fuel line retainer clip

Autozone should have it in there help line, also new clips come with new fuel filter, or stop by ant repair shop there always some laiding around, I know we do, but that don't help you, sorry.

Posted on Jul 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change 2003 kia optima sedan fuel filter


The fuel filter location varies with engine size on the Kia Optima. The 1.5-, 1.6- and 2.4-liter engines have the fuel filter located under the car in the front left corner of the fuel tank. The 1.8-liter engine has the fuel filter located on the driver's side firewall. All the filters have the same replacement procedure. There are actually two filters on the Kia Optima. A filter called a strainer is attached to the intake side of the fuel pump inside the fuel tank.

To change the filter follow this procedure:-

•Lift the hood and remove the cap on the fuse and relay box located on the driver's side fenderwell. Look at the bottom of the cap for the location of the fuel pump relay within the box. Pull the fuel pump relay out and lay it sideways in the box.

•2
Start the engine. It is not likely to start and even if it does it will only run for a second since the fuel pump relay has been removed, which disabled the fuel pump. This procedure will drop the fuel pressure in the fuel line. Raise the rear of the vehicle with the floor jack and support it by the frame with the jack stands. This is for engines 1.5, 1.6 and 2.4.

•3
Remove the fuel lines on both ends of the fuel filter. Use the scribe--a long pointy needle--to lift the white retainer straight up located in the center of the connector. This releases the fuel line from the fuel pump. Do the same to the other side of the fuel pump.

•4
Remove the bolt in the center of the fuel pump retainer bracket using a 10 mm socket. Pull the fuel pump out of the bracket.

•5
Insert the new fuel pump into the retainer bracket. Make sure that the inlet side faces the fuel line to the fuel tank and the outlet toward the fuel line to the engine. Install the fuel pump and bracket and tighten the bolt.

•6
Place a white retainer clip that came with the filter into the holes in each of the connectors. Just push it in enough to snap the bottom ends of the clip in place. The clip should now be standing straight up with just the bottom tips in the connectors. Push each of the fuel lines into the filter one at a time. Holding the fuel line tightly into the filter, push the white retainer clip down to lock the fuel filter and fuel line together. Lower the car and replace the fuel pump relay. Start the car and check for leaks.

Jun 19, 2014 | 2003 Kia Optima

1 Answer

How to change fuel filter on 1997 Ford 150


Things You'll Need

  • Drop pan
  • Socket set
  • Fuel line disconnect tool
  • New filter

  • 1Slide the drip pan under the driver side of the truck, below the driver door. Climb under with the socket set, fuel line disconnect tool and new filter.
  • 2Unbolt the fuel filter retaining strap with the socket set. The filter is located along the inboard side of the frame, below the driver seat. When in doubt, simply follow the fuel lines forward from the fuel tank until you locate the filter.
  • 3Disconnect the front fuel line from the fuel filter with the fuel line disconnect tool. The line flares out where the filter outlet enters it and a retaining clip holds it in place. You can unseat this clip with a pocket screwdriver or a pick, but it's not advisable, as the clip tends to break if pried on unevenly. hence why u need the tool. about ten buck
  • 4Pull the fuel line off the front of the fuel filter and then pull the filter out of the rear line and retaining strap. Put the old filter in the drip pan.
  • 5Slide the new filter into the retaining strap and plug the inlet into the rear fuel line. Make sure the arrow indicating flow direction points toward the engine. Connect the front fuel line, push the retaining clip back into place and bolt the retaining strap back to the frame.
  • 6Climb out, get in the truck and turn the ignition key to the run position. Wait for the fuel pump to stop running (this should be about 10 seconds) and start the truck.

Nov 18, 2011 | 1997 Ford F150 Regular Cab

2 Answers

Removal of gas tank


Fuel Tank Assembly Removal & Installation Single Tank To Remove:
  1. Before servicing the vehicle refer to the precautions at the beginning of this section
  2. Relieve fuel system pressure (See: Fuel System Relieving)
  3. Disconnect the negative battery cable
  4. Raise and support the vehicle
  5. Drain the fuel tank in an approved container
  6. Remove or disconnect the following:
    • evaporative emission (EVAP) canister Disconnect fuel lines for single tank gm_trk_sub15_fuel_line_rem_singl_tnk.gif

    • Chassis fuel lines (B) at the fuel tank (A)
      1. Cap the fuel and EVAP lines to prevent possible fuel system contamination
      Disconnect EVAP vent line gm_trk_sub15_evap_vent_line_rem.gif

    • EVAP vent line at the fuel tank clip (E) Disconnect vent hose and filler hose gm_trk_sub15_vent_filler_hoses.gif

    • Vent hose and filler hose clamp (D, B)
    • Vent hose and filler hose from the line
    Fuel tank removal gm_trk_sub15_fuel_tank_rem.gif

  7. With the aid of an assistant or a suitable jack support the fuel tank
  8. Remove or disconnect the following:
    • Fuel tank strap attaching bolts
    • Fuel tank straps
  9. Carefully lower the rear of the fuel tank slightly
  10. Remove or disconnect the following:
    • Fuel sender cover Fuel tank connections gm_trk_sub15_fuel_tank_conn.gif

    • Fuel sender and the fuel pressure sensor electrical connectors
    • Fuel tank
  11. Place the fuel tank in a suitable work area Fuel lines at the tank gm_trk_sub15_fuel_lines_at_tank.gif

  12. Remove or disconnect the following:
    • Fuel feed and return lines (C) from the fuel sender and the retaining clips
    • Fuel pump assembly from the fuel tank
    • EVAP line from the fuel tank roll over valves (B, D) and the retaining clips (A)
    • Fuel fill hose and the vent hose from the fuel tank
    • Fuel tank
To Install:
  1. Install or connect the following:
    • EVAP line to the fuel tank roll over valves and the retaining clips
    • Fuel pump assembly to the fuel tank
    • Fuel feed and return lines to the fuel sender and the retaining clips
    • Fuel fill hose and the vent hose to the fuel tank; torque hose clamps,
      1. Torque to: 22 lb-in. (2.5 Nm)
  2. With the aid of an assistant or a suitable jack support and partially raise the fuel tank front end first
  3. Install or connect the following:
    • Fuel sender and the fuel pressure sensor electrical connectors
    • Fuel sender cover
  4. Fully raise the fuel tank
  5. Install or connect the following:
    • Fuel tank straps
    • Install the fuel tank strap attaching bolts;
      1. Torque to 30 lb-ft. (40 Nm)
    • Fuel fill hose and the vent hose to the lines;
      1. Torque hose clamp to 22 lb-in. (2.5 Nm)
  6. Torque the vent hose clamp,
    • Torque to: 22 lb-in. (2.5 Nm)
  7. Connect the EVAP vent line to the fuel tank clip
  8. Remove the caps from the fuel and EVAP lines
  9. Install or connect the following:
    • chassis fuel lines at the fuel tank
    • EVAP canister
  10. Lower the vehicle to the ground
  11. Fill the fuel tank with clean fuel
  12. Install the fuel filler cap
  13. Connect the negative battery cable
  14. Use the following procedure to inspect for leaks:
    • Turn the ignition on for two seconds
    • Turn the ignition off for 10 seconds
    • Turn the ignition on
    • Inspect for fuel leaks
  15. Install the engine sight shield
  16. Road test the vehicle to check performance

Feb 12, 2011 | 2000 GMC Sierra

1 Answer

Where the fuel filter located on a 2002 Ford explorer


your fuel filter is well hid !! the fuel tank is on the passengers side of your explorer on the fuel filer is located on the front top of your fuel tank ! access to the filter is obtained by removing the heat shield at the front of the fuel tank, there are two bolts retaining the shield to the right frame rail and two bolts retaining the shield to the cross member. once the shield is removed you will see the filter,Be careful removing the fuel lines, the lines have locking clips that DO NOT remove from the lines !! and can be damage if you are not careful (which will result in complete line replacement if the ends are broken. the line clips are released by disengaging the top of the clip then folding the the edge over towards the side its attached to next push both side's in (towards center on top edge) then push clip down part way while pulling line loose .Good luck Thanks for using fix ya

Jan 20, 2011 | 2002 Ford Explorer

1 Answer

Overreving with no power and excessive gas consumption air filter cleaned map sensor replaced fuel pump and filter


usually caused by busted diaphram in fuel pressure regulator allowing fuel to be drawn thru regulator directly to intake manifold. Pull vacuum line off regulator, plug line with golf tee, start car and watch to see if gas comes out of regulator. If yes, turn off car, replace regulator. The regulator sits near the fuel rail on the top of the engine as shown below. I will paste replacement instructions below from autozone.com in case you need to replace the regulator. Please let me know if you have any questions.
jturcotte_421.gif


Removal & Installation

4.2L Engine

  1. Relieve the fuel system pressure.
  2. Remove the air cleaner outlet resonator.
  3. Disconnect the engine wiring harness from the retaining clips at the front of the engine.
  4. Disconnect the fuel pressure regulator vacuum line.
  5. Clean any dirt from the fuel pressure regulator and the surrounding area.
  6. Disconnect the fuel return pipe.
  7. Remove the fuel return pipe retainer.
  8. Remove the fuel pressure regulator retainer.
  9. Remove the fuel pressure regulator.
  10. Inspect the regulator filter screen for contamination. If contaminated, replace the fuel pressure regulator.

To install:
  1. Install the regulator filter.
  2. Install the new O-ring on the fuel pressure regulator.
  3. Lubricate the fuel pressure regulator O-ring with clean engine oil.
  4. Push the fuel pressure regulator into the regulator housing on the fuel rail.
  5. Install the fuel pressure regulator retainer. Tighten the regulator retainer screw to 71 inch lbs. (8 Nm).
  6. Install the fuel return pipe retainer. Tighten the return pipe retainer screw to 71 inch lbs. (8 Nm).
  7. Connect the fuel return pipe.
  8. Connect the fuel pressure regulator vacuum line.
  9. Connect the negative battery cable.
  10. Inspect for leaks:
    1. Turn ON the ignition for 2 seconds.
    2. Turn OFF the ignition for 10 seconds.
    3. Turn ON the ignition.
    4. Inspect for fuel leaks.

  11. Install the engine wiring harness into the retaining clips at the front of the engine.
  12. Install the air intake resonator.

Dec 08, 2010 | 2002 Chevrolet TrailBlazer

1 Answer

2005 toyota corolla. no problems yesterday..this morning it was dead. I can jump it and it turns over but it won't stay running. doesn't seem to be getting any fuel. Which fuse could be causing this...


Fuel Pump-(test for current at the fuel pump using a multimeter or test light while cranking) Removal & Installation To Remove:
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Relieve fuel system pressure.
  3. Disconnect the battery ground cable.
  4. Remove the rear seat cushion.
  5. Remove the rear floor service cover mounting screws and remove the cover (except '02-'04). toy_car_cor-02-04fuelpump2.gif

  6. Remove the butyl tape and remove the floor service cover ('02-'04).
  7. Remove the fuel pump vapor pressure sensor electrical connector ('02-'04).
  8. Remove the fuel line U-clip and remove the fuel line from the fuel pump module.
  9. Squeeze the fuel vent line retainer and remove the vent line from the fuel pump module. toy_car_cor-02-04fuelpump1.gif

  10. Remove the 8 fuel pump module retainer ring mounting screws and remove the retainer ring ('02-'04).
  11. Remove the fuel pump module retainer using special tool 09808- 14020 or equivalent (except '02-'04).
  12. Remove the fuel pump module.
To Install:
  1. Install a new O-ring on the fuel tank.
  2. Install the fuel pump module into the fuel tank.
  3. Use the following procedure to install the fuel pump module retainer ring (except '02-'04). Fuel pump module installation toy_cor-05-18-1203.gif

    1. Align the notch in the fuel tank with the tab in the module.
    2. Matchmark a new retainer with the fuel tank.
    3. Using the special tool install and tighten the retainer ring 2 revolutions.
  4. Use the following procedure to install the fuel tank module retainer ring ('02-'04).
    1. Install the retainer ring on the fuel pump module.
    2. Fasten the retainer with the 8 mounting screws. Tighten 53 in lb (6 Nm).
  5. Install the vent line to the pipe until the fuel vent line connector clicks into place.
  6. Install the fuel line with the U-clip.
  7. Install the fuel pump vapor pressure sensor electrical connector ('02-'04).
  8. Install the floor service cover with butyl tape ('02-'04).
  9. Install and secure the rear floor service cover with the mounting screws (except '02-'04).
  10. Install the rear seat cushion.
  11. Connect the battery ground cable.
  12. Check for fuel leaks.
prev.gif next.gif

Oct 16, 2010 | 2005 Toyota Corolla

1 Answer

My escort has no go power like its getting no gas


Try a fuel filter:
Fuel Filter REMOVAL & INSTALLATION The in-line fuel filter is located in the engine compartment between the fuel tank and the fuel rail.
  1. Properly relieve the fuel system pressure.
  2. Disconnect the negative battery cable.
  3. Position a suitable container below the fuel filter to collect any excess fuel that may leak from the filter and lines. CAUTION
    Observe all applicable safety precautions when working around fuel. Whenever servicing the fuel system, always work in a well ventilated area. Do not allow fuel spray or vapors to come in contact with a spark or open flame. Keep a dry chemical fire extinguisher near the work area. Always keep fuel in a container specifically designed for fuel storage; also, always properly seal fuel containers to avoid the possibility of fire or explosion.
  4. Remove the retaining clip from the fuel filter upper hose.
  5. Disconnect the upper hose from the fuel filter and drain any excess fuel into the container. Plug the hose.
  6. Raise and safely support the vehicle.
  7. Remove the retaining clip from the fuel filter lower hose.
  8. Disconnect the lower hose from the fuel filter and drain any excess fuel into the container. Plug the hose.
  9. Lower the vehicle.
  10. Unfasten the filter retaining clamp screw and remove the fuel filter. Fig. 1: The fuel filter is located in the engine compartment, between the fuel tank and fuel rail — 1.9L engine's underside shown 90981p47.jpg
    Fig. 2: To remove the fuel filter upper hose clip, grasp the clip (arrow) . . . 90981p48.jpg
    Fig. 3: . . . and gently pull the clip from the hose. (Lower hose clip removal is similar) 90981p49.jpg
    Fig. 4: Grasp the hose and pull it from the fuel filter 90981p50.jpg
    Fig. 5: Unfasten the filter retaining clamp screw 90981p51.jpg
    Fig. 6: Grasp the filter and remove it from the vehicle 90981p52.jpg
    To install:
  11. Position the fuel filter and tighten the filter mounting clamp.
  12. Remove the plug, then connect the upper hose to the filter and install the hose retaining clip.
  13. Raise and safely support the vehicle.
  14. Remove the plug, connect the lower hose to the filter and install the hose retaining clip.
  15. Lower the vehicle.
  16. Connect the negative battery cable.
  17. Start the engine and check for leaks.
prev.gif next.gif

Aug 01, 2010 | 1995 Ford Escort

1 Answer

I am trying to change fuel filter on 1995 ford econoline f-350 It appered that the fuel lines were held on by push on retaining clips but after removing the retaining clips I still cannot seem to get the...


Yes you do, The first clips you removed are the secondary clips. The lines have to be released from the inside. Heres the info.. Cobra :-)
Removal
  1. Open safety clip.

    v9067a.gif

  1. Fit Tool T90T-9550-B (5/16 inch) or T90T-9550-C (3/8 inch) to coupling so that tool can enter female fitting.

    v9068a.gif

  1. Push the tool into female fitting to release the retaining fingers from the formed male tube end.
  1. Pull male and female fittings apart.

    v9069a.gif

  1. Remove the tool from the disconnected fitting.
  1. Inspect the fitting for any internal parts that may have been damaged. Fuel tube should be replaced if internal parts are damaged.

Jun 05, 2010 | 1995 Ford Econoline

1 Answer

Where is fuel pressure regulatore located


For 2000 Chevrolet Truck Blazer 4WD 4.3L SFI 6cyl
If your engine is a 4.3L V-6 with CPI (central point injection) it is inside the upper intake manifold. The upper intake manifold is bolted on top of the normal intake manifold.

The throttle body is mounted on it and your fuel lines terminate into the center of this.


Removal & Installation
  1. Relieve the fuel system pressure.
  2. Remove the air cleaner outlet resonator.
  3. Disconnect the engine wiring harness from the retaining clips at the front of the engine.
  4. Disconnect the fuel pressure regulator vacuum line.
  5. Clean any dirt from the fuel pressure regulator and the surrounding area.
  6. Disconnect the fuel return pipe.
  7. Remove the fuel return pipe retainer.
  8. Remove the fuel pressure regulator retainer.
  9. Remove the fuel pressure regulator.
  10. Inspect the regulator filter screen for contamination. If contaminated, replace the fuel pressure regulator.
To install:


aaf5240.jpg
Fig. Fuel pressure regulator-4.2L engine
  1. Install the regulator filter.
  2. Install the new O-ring on the fuel pressure regulator.
  3. Lubricate the fuel pressure regulator O-ring with clean engine oil.
  4. Push the fuel pressure regulator into the regulator housing on the fuel rail.
  5. Install the fuel pressure regulator retainer. Tighten the regulator retainer screw to 71 inch lbs. (8 Nm).
  6. Install the fuel return pipe retainer. Tighten the return pipe retainer screw to 71 inch lbs. (8 Nm).
  7. Connect the fuel return pipe.
  8. Connect the fuel pressure regulator vacuum line.
  9. Connect the negative battery cable.
  10. Inspect for leaks:
    1. Turn ON the ignition for 2 seconds.
    2. Turn OFF the ignition for 10 seconds.
    3. Turn ON the ignition.
    4. Inspect for fuel leaks.
  11. Install the engine wiring harness into the retaining clips at the front of the engine.
  12. Install the air intake resonator.
Hope help with this (remember rated this post).

Feb 26, 2010 | 2000 Chevrolet Blazer

2 Answers

How do i change a fuel filter on a 2001 f150


The clamps are just a secondary lock, special tools are needed to unlock the fuel lines.

Nov 05, 2009 | 2001 Ford F150 Styleside SuperCrew

Not finding what you are looking for?
2005 Ford Freestar Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...