Question about 2010 Jeep Commander

Open Question

How to reset change oil message on a 2010 jeep commander

Message on dash says change oil but it had a oil change already.

Posted by Anonymous on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 206 Answers

SOURCE: how do you reset the perform service message after

http://www.jeep.com/en/owners/manuals/index.html?year=2006&nameplate=Grand%20Cherokee

That should allow you to download a copy of the owner's manual that will detail the reset procedure.

Basically, on Jeep products you

To reset the oil change indicator system (after
performing the scheduled maintenance), refer to the
following procedure:
1. Turn the ignition switch to the ON position (Do not
start the engine).
2. Fully depress the accelerator pedal slowly three
times within 10 seconds.
3. Turn the ignition switch to the OFF/LOCK position.
NOTE: If the indicator message illuminates when you
start the vehicle, the oil change indicator system did not
reset. If necessary repeat this procedure.

Posted on Oct 01, 2009

Ad
  • 2418 Answers

SOURCE: do you have an oil

You have to get under the car. The oil pan is right there in the middle of the car. and it has a bolt (drain plug) sticking out to the rear (hump that hangs down behind the steering cross member). This picture is for a 4 wheel drive. Your drain plug may be on the other side of the engine but you get the idea. ---->>>>>9bd281b.gif

Posted on Oct 18, 2010

  • 2 Answers

SOURCE: 2006 Jeep Commander dash display reports "Service

It cant hurt to check your spare. It may need a bit more air.

:)

Posted on Dec 22, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Change oil change light in 2010 Jeep grand Cherokee


If you are trying to reset it just turn the key from the off position to on and press the gas pedal 5 times completely to the floor in about 10 seconds. Then start the engine.

Mar 14, 2015 | 2010 Jeep Grand Cherokee

1 Answer

I have 2010 Jeep Commander 3.7L V6. I took the spark plug wires off to change them and didn't memorize how they go back on. The problem is there are three coils on the right side of the engine (facing...


click this link, find your engine and click the picture to enlarge it.
https://www.google.com/search?q=2010+jeep+commander+spark+plug+wiring+diagram&client=aff-maxthon-maxthon4&hs=0e0&affdom=maxthon.com&sa=x&channel=t26&biw=925&bih=609&tbm=isch&tbo=u&source=univ&ei=xdy_vidsb4kmggty2ihidq&ved=0cdoq7ak

Jan 21, 2015 | 2010 Jeep Commander

1 Answer

How do I remove my 2010 Jeep Commander dash to get to the heater flap?


the fsm covers this.
controls bad.
damper bad.
or the damp flap stuck
simple tests in the FSM cover this., as does the removal.

Sep 23, 2014 | 2010 Jeep Commander

1 Answer

Keyless remote is not working


Sorry dealer only software

Nov 12, 2012 | 2010 Jeep Commander

1 Answer

How to reset change engine oil light after replace the oil ina ford taurus 2010


Press setup button until you see remaining oil life message (it will say like 9% or something) so the message will kind of look like this

Oil life remaining
9%
Hold reset for new

When you see this, hold the reset button. This will reset the oil life to 100%

Nov 30, 2010 | 2010 Ford Taurus

2 Answers

I have a 2009 Ford Escape XLT. I had an oil change at 1500 miles and have since driven 275 miles since the oil change. I have an oil change advisory allumination notification on the dash now. How do I...


This is how it works on my 2010 Escape. There are 3 buttons to the lower left of your steering column (Info, Setup, and Reset):
1) when it's displaying the "oil change required" message, hit the "reset" button to get rid of the message2) then hit the "Setup" button twice and you'll see the "oil life" screen, which is now at "0%". It tells you what to do next (i.e. "hold reset" until it says 100%).

Oct 01, 2010 | 2009 Ford Escape Hybrid

2 Answers

I need to know how to fix the oil change light after a oil change on 2009 mercury grand marque. The panel on the car always says ''change oil soon'' but the oil has already been changed.


Hi!!

The person that changed the oil should have resetted the light.

Just drive to an AutoZone store, ask for somebody to check your vehicle computer codes, once they check them up, ask them to reset the change oil soon light, they would do this at no charge. This is a free service they offered to all their customers.

Don't forget to rate this post. Good luck!!

May 23, 2010 | 2009 Mercury Grand Marquis

1 Answer

The service system light came on.what does that mean


Time to change the oil !!! service light can be reset for 3000 miles on dash panel.

Jan 08, 2010 | 2006 Jeep Commander

Not finding what you are looking for?
2010 Jeep Commander Logo

Related Topics:

122 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...